oSIST prEN ISO/ASTM 52904:2022

Additive manufacturing of metals - Process characteristics and performance - Metal powder bed fusion process to meet critical applications (ISO/ASTM DIS 52904:2022)

1.1 This practice describes the operation and production control of metal powder bed fusion (PBF) machines and processes to meet critical applications such as commercial aerospace components and medical implants. The requirements contained herein are applicable for production components and mechanical test specimens using powder bed fusion (PBF) with both laser and electron beams.
1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appro-priate safety, health, and environmental practices and deter-mine the applicability of regulatory limitations prior to use.
1.3 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for the Development of International Standards, Guides and Recom-mendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Additive Fertigung von Metallen - Prozessanforderungen und Qualifizierung - Pulverbettbasiertes Schmelzen von Metallen für kritische Anwendungen (ISO/ASTM DIS 52904:2022)

Fabrication additive de métaux - Caractéristiques et performances du procédé - Procédé de fusion sur lit de poudre métallique en vue de répondre aux applications critiques (ISO/ASTM DIS 52904:2022)

1.1 La présente pratique décrit le fonctionnement et le contrôle de production des machines et des procédés de fusion sur lit de poudre métallique (PBF) pour répondre à des applications critiques, telles que les composants aérospatiaux commerciaux et les implants médicaux. Les exigences contenues ci-après sont applicables aux composants de production et aux éprouvettes d'essai mécaniques utilisant la fusion sur lit de poudre (PBF) avec des faisceaux laser et électroniques.
1.2 La présente norme ne prétend pas traiter de tous les problèmes de sécurité, s'ils existent, associés à son utilisation. Il est de la responsabilité de l'utilisateur de la présente norme d'établir des pratiques de sécurité, d'hygiène et d'environnement appropriées, et de déterminer l'applicabilité des restrictions réglementaires avant utilisation.
1.3 La présente Norme internationale a été élaborée conformément aux principes internationalement reconnus de normalisation établis dans la Décision sur les principes pour l'élaboration de normes internationales, guides et recommandations publiée par le Comité des obstacles techniques au commerce (OTC) de l'Organisation mondiale du commerce.

Aditivna proizvodnja kovinskih izdelkov - Značilnosti in tehnične lastnosti procesa - Proces spajanja kovinskega prahu v postelji za doseganje kritičnih/zahtevnih aplikacij (ISO/ASTM DIS 52904:2022)

General Information

• Status: Not Published
• Public Enquiry End Date: 02-Jan-2023
• ICS: 25.030 - Additive manufacturing
• Technical Committee: VAR - Welding
• Current Stage: 4020 - Public enquire (PE) (Adopted Project)
• Start Date: 27-Oct-2022
• Due Date: 16-Mar-2023
• Completion Date: 12-Jan-2023
• Ref Project: prEN ISO/ASTM 52904 - Additive manufacturing of metals - Process characteristics and performance - Metal powder bed fusion process to meet critical applications (ISO/ASTM DIS 52904:2022)

Relations

• Revised: SIST EN ISO/ASTM 52904:2020 - Additive manufacturing - Process characteristics and performance - Practice for metal powder bed fusion process to meet critical applications (ISO/ASTM 52904:2019)
• Effective Date: 01-Dec-2022

Standards Content (Sample)

SLOVENSKI STANDARD
oSIST prEN ISO/ASTM 52904:2022
01-december-2022
Aditivna proizvodnja kovin - Značilnosti in tehnične lastnosti procesa - Proces
fuzije plasti kovinskih prašnih delcev za doseganje kritičnih aplikacij (ISO/ASTM
DIS 52904:2022)
Additive manufacturing of metals - Process characteristics and performance - Metal
powder bed fusion process to meet critical applications (ISO/ASTM DIS 52904:2022)
Additive Fertigung von Metallen - Prozessanforderungen und Qualifizierung -
Pulverbettbasiertes Schmelzen von Metallen für kritische Anwendungen (ISO/ASTM DIS
52904:2022)
Fabrication additive de métaux - Caractéristiques et performances du procédé - Procédé
de fusion sur lit de poudre métallique en vue de répondre aux applications critiques
(ISO/ASTM DIS 52904:2022)
Ta slovenski standard je istoveten z: prEN ISO/ASTM 52904
ICS:
25.030 3D-tiskanje Additive manufacturing
oSIST prEN ISO/ASTM 52904:2022 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN ISO/ASTM 52904:2022

---------------------- Page: 2 ----------------------
oSIST prEN ISO/ASTM 52904:2022
DRAFT INTERNATIONAL STANDARD
ISO/ASTM DIS 52904
ISO/TC 261 Secretariat: DIN
Voting begins on: Voting terminates on:
2022-10-12 2023-01-04
Additive manufacturing of metals — Process
characteristics and performance — Metal powder bed
fusion process to meet critical applications
Fabrication additive de métaux — Caractéristiques et performances du procédé — Procédé de fusion sur lit
de poudre métallique en vue de répondre aux applications critiques
ICS: 25.030
This document is circulated as received from the committee secretariat.
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENT AND APPROVAL. IT IS
ISO/CEN PARALLEL PROCESSING
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/ASTM DIS 52904:2022(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION. © ISO/ASTM International 2022

---------------------- Page: 3 ----------------------
oSIST prEN ISO/ASTM 52904:2022
ISO/ASTM DIS 52904:2022(E)
DRAFT INTERNATIONAL STANDARD
ISO/ASTM DIS 52904
ISO/TC 261 Secretariat: DIN
Voting begins on: Voting terminates on:

Additive manufacturing of metals — Process
characteristics and performance — Metal powder bed
fusion process to meet critical applications
Fabrication additive de métaux — Caractéristiques et performances du procédé — Procédé de fusion sur lit
de poudre métallique en vue de répondre aux applications critiques
ICS: 25.030
This document is circulated as received from the committee secretariat.
COPYRIGHT PROTECTED DOCUMENT
© ISO/ASTM International 2022 THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENT AND APPROVAL. IT IS
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
ISO/CEN PARALLEL PROCESSING
THEREFORE SUBJECT TO CHANGE AND MAY
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
NOT BE REFERRED TO AS AN INTERNATIONAL
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below STANDARD UNTIL PUBLISHED AS SUCH.
or ISO’s member body in the country of the requester. In the United States, such requests should be sent to ASTM International.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
ISO copyright office ASTM International
TECHNOLOGICAL, COMMERCIAL AND
CP 401 • Ch. de Blandonnet 8 100 Barr Harbor Drive, PO Box C700
USER PURPOSES, DRAFT INTERNATIONAL
CH-1214 Vernier, Geneva West Conshohocken, PA 19428-2959, USA
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
Phone: [phone] Phone: [phone]
POTENTIAL TO BECOME STANDARDS TO
Fax: [phone]
WHICH REFERENCE MAY BE MADE IN
Reference number
Email: [e-mail] Email: [e-mail]
NATIONAL REGULATIONS.
Website: www.iso.org Website: www.astm.org ISO/ASTM DIS 52904:2022(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
Published in Switzerland
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
ii
  © ISO/ASTM International 2022 – All rights reserved
PROVIDE SUPPORTING DOCUMENTATION. © ISO/ASTM International 2022

---------------------- Page: 4 ----------------------
oSIST prEN ISO/ASTM 52904:2022
ISO/ASTM D
...