SIST EN 301 908-11 V5.2.1:2011
(Main)IMT cellular networks - Harmonized EN covering the essential requirements of article 3.2 of the R&TTE Directive - Part 11: CDMA Direct Spread (UTRA FDD) (Repeaters)
IMT cellular networks - Harmonized EN covering the essential requirements of article 3.2 of the R&TTE Directive - Part 11: CDMA Direct Spread (UTRA FDD) (Repeaters)
The present document applies to the following radio equipment type:
• Repeaters for IMT-2000 CDMA Direct Spread (UTRA FDD).
This radio equipment type is capable of operating in all or any part of the frequency bands given in table 1-1.
The present document covers requirements for UTRA FDD Repeater for Releases 4, 5, 6, 7, 8 and 9. In addition, the present document covers requirements for UTRA Repeater in the operating bands specified in TS 102 735 [i.5].
The present document is intended to cover the provisions of Directive 1999/5/EC [i.6] (R&TTE Directive), article 3.2, which states that "… radio equipment shall be so constructed that it effectively uses the spectrum allocated to terrestrial/space radio communications and orbital resources so as to avoid harmful interference".
In addition to the present document, other ENs that specify technical requirements in respect of essential requirements under other parts of article 3 of the R&TTE Directive [i.6] may apply to equipment within the scope of the present document.
Celična omrežja IMT - Harmonizirani EN, ki zajema bistvene zahteve člena 3.2 direktive R&TTE - 11. del: CDMA z neposrednim razprševanjem (“Direct Spread”) (UTRA FDD) (ponavljalniki (repetitorji))
Ta dokument velja za naslednjo vrsto radijske opreme:
• ponavljalnike za IMT-2000 neposredno razprševanje (UTRA FDD).
Ta vrsta radijske opreme je zmožna delovati v vseh ali katerem koli delu frekvenčnega pasu, kot so navedeni v preglednici 1-1.
Ta dokument zajema zahteve za ponavljalnik UTRA FDD za izdaje 4, 5, 6, 7, 8 in 9. Poleg tega ta dokument zajema zahteve za ponavljalnik UTRA v pasovih delovanja, določenih v TS 102 735 [i.5].
Ta dokument zajema določbe člena 3.2. Direktive 1999/5/ES [i.6] (direktive R&TTE), ki navaja, da » … radijska oprema je narejena tako, da učinkovito izrablja spekter, razporejen za prizemne/vesoljske radiokomunikacije in orbitalne vire, tako da ne pride do škodljivega motenja«.
Poleg tega dokumenta se preostali EN, ki določajo tehnične zahteve v skladu z bistvenimi zahtevami v drugih delih člena 3 direktive R&TTE [i.6], lahko uporabljajo za opremo v okviru uporabe tega dokumenta.
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 301 908-11 V5.2.1:2011
01-september-2011
&HOLþQDRPUHåMD,07+DUPRQL]LUDQL(1NL]DMHPDELVWYHQH]DKWHYHþOHQD
GLUHNWLYH5 77(GHO &'0$]QHSRVUHGQLPUD]SUãHYDQMHP ³'LUHFW6SUHDG´
875$)'' SRQDYOMDOQLNL UHSHWLWRUML
IMT cellular networks - Harmonized EN covering the essential requirements of article 3.2
of the R&TTE Directive - Part 11: CDMA Direct Spread (UTRA FDD) (Repeaters)
Ta slovenski standard je istoveten z: EN 301 908-11 Version 5.2.1
ICS:
33.060.99 Druga oprema za radijske Other equipment for
komunikacije radiocommunications
SIST EN 301 908-11 V5.2.1:2011 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 301 908-11 V5.2.1:2011
---------------------- Page: 2 ----------------------
SIST EN 301 908-11 V5.2.1:2011
ETSI EN 301 908-11 V5.2.1 (2011-07)
Harmonized European Standard
IMT cellular networks;
Harmonized EN covering the essential requirements
of article 3.2 of the R&TTE Directive;
Part 11: CDMA Direct Spread (UTRA FDD) (Repeaters)
---------------------- Page: 3 ----------------------
SIST EN 301 908-11 V5.2.1:2011
2 ETSI EN 301 908-11 V5.2.1 (2011-07)
Reference
REN/MSG-TFES-006-11
Keywords
3G, 3GPP, cellular, digital, IMT, IMT-2000,
mobile, radio, regulation, repeater, testing,
UMTS, UTRA, WCDMA
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
Individual copies of the present document can be downloaded from:
http://www.etsi.org
The present document may be made available in more than one electronic version or in print. In any case of existing or
perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF).
In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive
within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
http://portal.etsi.org/chaircor/ETSI_support.asp
Copyright Notification
No part may be reproduced except as authorized by written permission.
The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2011.
All rights reserved.
TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI
---------------------- Page: 4 ----------------------
SIST EN 301 908-11 V5.2.1:2011
3 ETSI EN 301 908-11 V5.2.1 (2011-07)
Contents
Intellectual Property Rights . 5
Foreword . 5
Introduction . 6
1 Scope . 7
2 References . 7
2.1 Normative references . 7
2.2 Informative references . 8
3 Definitions, symbols and abbreviations . 8
3.1 Definitions . 8
3.2 Symbols . 9
3.3 Abbreviations . 9
4 Technical requirements specifications . 10
4.1 Environmental profile . 10
4.2 Conformance requirements . 10
4.2.1 Introduction. 10
4.2.2 Operating band unwanted emissions . 11
4.2.2.1 Definition . 11
4.2.2.2 Limit . 11
4.2.2.2.1 General operating band unwanted emission requirements . 11
4.2.2.2.2 Operating band emission mask requirements . 11
4.2.2.2.3 Protection of the BS receiver in the operating band . 13
4.2.2.2.4 Co-existence with services in adjacent frequency bands . 13
4.2.2.2.5 Protection of DTT. 13
4.2.2.3 Conformance . 14
4.2.3 Spurious emissions . 14
4.2.3.1 Definition . 14
4.2.3.2 Limit . 14
4.2.3.2.1 Spurious emissions . 15
4.2.3.2.2 Co-existence with other systems . 15
4.2.3.3 Conformance . 16
4.2.4 Maximum output power . 16
4.2.4.1 Definition . 16
4.2.4.2 Limit . 16
4.2.4.3 Conformance . 17
4.2.5 Input intermodulation . 17
4.2.5.1 Definition . 17
4.2.5.2 Limit . 17
4.2.5.2.1 General input intermodulation requirement . 17
4.2.5.2.2 Co-existence with other systems . 18
4.2.5.3 Conformance . 19
4.2.6 Out of band gain . 19
4.2.6.1 Definition . 19
4.2.6.2 Limits . 19
4.2.6.3 Conformance . 19
4.2.7 Adjacent Channel Rejection Ratio . 19
4.2.7.1 Definition . 19
4.2.7.2 Limit . 20
4.2.7.3 Conformance . 20
4.2.8 Output intermodulation . 20
4.2.8.1 Definition . 20
4.2.8.2 Limit . 20
4.2.8.3 Conformance . 20
5 Testing for compliance with technical requirements . 20
ETSI
---------------------- Page: 5 ----------------------
SIST EN 301 908-11 V5.2.1:2011
4 ETSI EN 301 908-11 V5.2.1 (2011-07)
5.1 Environmental conditions for testing . 20
5.2 Interpretation of the measurement results . 21
5.3 Essential radio test suites . 22
5.3.1 Operating band unwanted emission . 22
5.3.1.1 Initial conditions . 22
5.3.1.2 Procedures . 23
5.3.2 Spurious emissions . 23
5.3.2.1 Initial conditions . 23
5.3.2.2 Procedure . 23
5.3.3 Maximum output power . 24
5.3.3.1 Initial conditions . 24
5.3.3.2 Procedure . 24
5.3.4 Input intermodulation . 24
5.3.4.1 Initial conditions . 24
5.3.4.2 Procedures . 25
5.3.5 Out of band gain . 25
5.3.5.1 Initial conditions . 25
5.3.5.2 Procedure . 25
5.3.6 Adjacent Channel Rejection Ratio . 25
5.3.6.1 Initial conditions . 25
5.3.6.2 Procedures . 26
5.3.7 Output intermodulation . 26
5.3.7.1 Initial conditions . 26
5.3.7.2 Procedures . 26
Annex A (normative): HS Requirements and conformance Test specifications Table
(HS-RTT) . 28
Annex B (normative): Repeater configurations . 30
B.1 Power supply . 30
B.2 Power supply options . 30
B.3 Combining of Repeaters . 30
Annex C (informative): Environmental profile specification . 31
Annex D (informative): The EN title in the official languages . 32
Annex E (informative): Bibliography . 33
History . 34
ETSI
---------------------- Page: 6 ----------------------
SIST EN 301 908-11 V5.2.1:2011
5 ETSI EN 301 908-11 V5.2.1 (2011-07)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (http://ipr.etsi.org).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This Harmonized European Standard (EN) has been produced by ETSI Technical Committee Mobile Standards Group
(MSG).
The present document has been produced by ETSI in response to mandate M/284 from the European Commission
issued under Council Directive 98/34/EC [i.1] (as amended) laying down a procedure for the provision of information
in the field of technical standards and regulations.
The title and reference to the present document are intended to included in the publication in the Official Journal of the
European Union of titles and references of Harmonized Standard under the Directive 1999/5/EC [i.6].
See article 5.1 of Directive 1999/5/EC [i.6] for information on presumption of conformity and Harmonised Standards or
parts thereof the references of which have been published in the Official Journal of the European Union.
The requirements relevant to Directive 1999/5/EC [i.6] are summarised in annex A.
The present document is part 11 of a multi-part deliverable covering the essential requirements under article 3.2 of
Directive 1999/5/EC [i.6] (R&TTE Directive) for Base Stations (BS), Repeaters and User Equipment (UE) for IMT
cellular networks, as identified below:
Part 1: "Introduction and common requirements";
Part 2: "CDMA Direct Spread (UTRA FDD) User Equipment (UE)";
Part 3: "CDMA Direct Spread (UTRA FDD) Base Stations (BS)";
Part 4: "CDMA Multi-Carrier (cdma2000) User Equipment (UE)";
Part 5: "CDMA Multi-Carrier (cdma2000) Base Stations (BS)";
Part 6: "CDMA TDD (UTRA TDD) User Equipment (UE)";
Part 7: "CDMA TDD (UTRA TDD) Base Stations (BS)";
Part 8: "Harmonized EN for IMT-2000, TDMA Single-Carrier (UWC 136) (UE) covering essential requirements
of article 3.2 of the R&TTE Directive";
Part 9: "Harmonized EN for IMT-2000, TDMA Single-Carrier (UWC 136) (BS) covering essential requirements
of article 3.2 of the R&TTE Directive";
Part 10: "Harmonized EN for IMT-2000, FDMA/TDMA (DECT) covering essential requirements of article 3.2 of
the R&TTE Directive";
Part 11: "CDMA Direct Spread (UTRA FDD) (Repeaters)";
Part 12: "Harmonized EN for IMT-2000, CDMA Multi-Carrier (cdma2000) (Repeaters) covering the essential
requirements of article 3.2 of the R&TTE Directive";
Part 13: "Evolved Universal Terrestrial Radio Access (E-UTRA) User Equipment (UE)";
ETSI
---------------------- Page: 7 ----------------------
SIST EN 301 908-11 V5.2.1:2011
6 ETSI EN 301 908-11 V5.2.1 (2011-07)
Part 14: "Evolved Universal Terrestrial Radio Access (E-UTRA) Base Stations (BS)";
Part 15: "Evolved Universal Terrestrial Radio Access (E-UTRA FDD) (Repeaters)";
Part 16: "Harmonized EN for IMT-2000, Evolved CDMA Multi-Carrier Ultra Mobile Broadband (UMB) (UE)
covering the essential requirements of article 3.2 of the R&TTE Directive";
Part 17: "Harmonized EN for IMT-2000, Evolved CDMA Multi-Carrier Ultra Mobile Broadband (UMB) (BS)
covering the essential requirements of article 3.2 of the R&TTE Directive";
Part 18: "E-UTRA, UTRA and GSM/EDGE Multi-Standard Radio (MSR) Base Station (BS)";
Part 19: "OFDMA TDD WMAN (Mobile WiMAX) TDD User Equipment (UE)";
Part 20: "OFDMA TDD WMAN (Mobile WiMAX) TDD Base Stations (BS)";
Part 21: "OFDMA TDD WMAN (Mobile WiMAX) FDD User Equipment (UE)";
Part 22: "OFDMA TDD WMAN (Mobile WiMAX) FDD Base Stations (BS)".
National transposition dates
Date of adoption of this EN: 4 July 2011
Date of latest announcement of this EN (doa): 31 October 2011
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 30 April 2012
Date of withdrawal of any conflicting National Standard (dow): 30 April 2013
Introduction
The present document is part of a set of standards developed by ETSI and is designed to fit in a modular structure to
cover all radio and telecommunications terminal equipment within the scope of the R&TTE Directive [i.6]. The
modular structure is shown in EG 201 399 [i.2].
ETSI
---------------------- Page: 8 ----------------------
SIST EN 301 908-11 V5.2.1:2011
7 ETSI EN 301 908-11 V5.2.1 (2011-07)
1 Scope
The present document applies to the following radio equipment type:
• Repeaters for IMT-2000 CDMA Direct Spread (UTRA FDD).
This radio equipment type is capable of operating in all or any part of the frequency bands given in table 1-1.
Table 1-1: UTRA Repeater operating bands
UTRA FDD Direction of transmission UTRA Repeater operating bands
Band
I Downlink 2 110 MHz to 2 170 MHz
Uplink 1 920 MHz to 1 980 MHz
III Downlink 1 805 MHz to 1 880 MHz
Uplink 1 710 MHz to 1 785 MHz
VII Downlink 2 620 MHz to 2 690 MHz
Uplink 2 500 MHz to 2 570 MHz
VIII Downlink 925 MHz to 960 MHz
Uplink 880 MHz to 915 MHz
XV Downlink 2 600 MHz to 2 620 MHz
Uplink 1 900 MHz to 1 920 MHz
XVI Downlink 2 585 MHz to 2 600 MHz
Uplink 2 010 MHz to 2 025 MHz
XX Downlink 791 MHz to 821 MHz
Uplink 832 MHz to 862 MHz
The present document covers requirements for UTRA FDD Repeater for Releases 4, 5, 6, 7, 8 and 9. In addition, the
present document covers requirements for UTRA Repeater in the operating bands specified in TS 102 735 [i.5].
The present document is intended to cover the provisions of Directive 1999/5/EC [i.6] (R&TTE Directive), article 3.2,
which states that "… radio equipment shall be so constructed that it effectively uses the spectrum allocated to
terrestrial/space radio communications and orbital resources so as to avoid harmful interference".
In addition to the present document, other ENs that specify technical requirements in respect of essential requirements
under other parts of article 3 of the R&TTE Directive [i.6] may apply to equipment within the scope of the present
document.
NOTE: A list of such ENs is included on the web site http://www.newapproach.org
2 References
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
reference document (including any amendments) applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
http://docbox.etsi.org/Reference.
NOTE: While any hyperlinks included in this clause were valid at the time of publication ETSI cannot guarantee
their long term validity.
2.1 Normative references
The following referenced documents are necessary for the application of the present document.
[1] Void.
[2] Void.
ETSI
---------------------- Page: 9 ----------------------
SIST EN 301 908-11 V5.2.1:2011
8 ETSI EN 301 908-11 V5.2.1 (2011-07)
[3] ETSI TS 125 143 (V9.2.0): "Universal Mobile Telecommunications System (UMTS); UTRA
repeater conformance testing (3GPP TS 25.143 version 9.2.0 Release 9)".
[4] ITU-R Recommendation SM.329-11 (2011): "Unwanted emissions in the spurious domain".
[5] ETSI TS 125 141 (V9.7.0): "Universal Mobile Telecommunications System (UMTS); Base
Station (BS) conformance testing (FDD) (3GPP TS 25.141 version 9.7.0 Release 9)".
[6] IEC 60068-2-1 (2007): "Environmental testing - Part 2-1: Tests - Test A: Cold".
[7] IEC 60068-2-2 (2007): "Environmental testing - Part 2-2: Tests - Test B: Dry heat".
[8] ETSI EN 301 908-1 (V5.2.1): "IMT cellular networks; Harmonized EN covering the essential
requirements of article 3.2 of the R&TTE Directive; Part 1: Introduction and common
requirements".
[9] ETSI EN 301 908-15 (V5.2.1): "IMT cellular networks; Harmonized EN covering the essential
requirements of article 3.2 of the R&TTE Directive; Part 15: Evolved Universal Terrestrial Radio
Access (E-UTRA FDD) (Repeaters)".
[10] ETSI TS 125 104 (V9.6.0): "Universal Mobile Telecommunications System (UMTS); Base
Station (BS) radio transmission and reception (FDD) (3GPP TS 25.104 version 9.6.0 Release 9)".
2.2 Informative references
The following referenced documents are not necessary for the application of the present document but they assist the
user with regard to a particular subject area.
[i.1] Directive 98/34/EC of the European Parliament and of the Council of 22 June 1998 laying down a
procedure for the provision of information in the field of technical standards and regulations.
[i.2] ETSI EG 201 399 (V2.2.1): "Electromagnetic compatibility and Radio spectrum Matters (ERM);
A guide to the production of Harmonized Standards for application under the R&TTE Directive".
[i.3] ETSI TR 102 215 (V1.3.1): "Electromagnetic compatibility and Radio spectrum Matters (ERM);
Recommended approach, and possible limits for measurement uncertainty for the measurement of
radiated electromagnetic fields above 1 GHz".
[i.4] ETSI TR 100 028 (all parts) (V1.4.1): "Electromagnetic compatibility and Radio spectrum Matters
(ERM); Uncertainties in the measurement of mobile radio equipment characteristics".
[i.5] ETSI TS 102 735 (V7.1.0): "Universal Mobile Telecommunications System (UMTS);
Band-specific requirements for UMTS Frequency Division Duplex (FDD) operation in the bands
1 900 MHz to 1 920 MHz paired with 2 600 MHz to 2 620 MHz and 2 010 MHz to 2 025 MHz
paired with 2 585 MHz to 2 600 MHz".
[i.6] Directive 1999/5/EC of the European Parliament and of the Council of 9 March 1999 on radio
equipment and telecommunications terminal equipment and the mutual recognition of their
conformity (R&TTE Directive).
3 Definitions, symbols and abbreviations
3.1 Definitions
For the purposes of the present document, the following terms and definitions apply:
donor coupling loss: coupling loss between the Repeater and the donor Base Station
downlink: signal path where Base Station transmits and mobile receives
downlink operating band: part of the operating band designated for downlink (BS transmit)
ETSI
---------------------- Page: 10 ----------------------
SIST EN 301 908-11 V5.2.1:2011
9 ETSI EN 301 908-11 V5.2.1 (2011-07)
maximum output power (Pmax): mean power level per carrier measured at the antenna connector of the Repeater in
specified reference condition
maximum rated output power: maximum rated output power of the repeater is the mean power level per carrier that
the manufacturer has declared to be available at the antenna connector
operating band: frequency range that is defined with a specific set of technical requirements, in which UTRA FDD
operates
NOTE: The operating band(s) for an UTRA FDD repeater is declared by the manufacturer according to the
designations in table 1-1. Operating bands for UTRA are designated with Roman numerals, while the
corresponding operating bands for E-UTRA are designated with Arabic numerals.
pass band: frequency range that the Repeater operates in with operational configuration
NOTE 1: This frequency range can correspond to one or several consecutive nominal 5 MHz channels. If they are
not consecutive each subset of channels has to be considered as an individual pass band.
NOTE 2: The Repeater can have one or several pass bands.
repeater: device that receives, amplifies and transmits the radiated or conducted RF carrier both in the downlink
direction (from the Base Station to the mobile area) and in the uplink direction (from the mobile to the Base Station)
uplink: signal path where mobile transmits and Base Station receives
uplink operating band: part of the operating band designated for downlink (BS transmit)
3.2 Symbols
For the purposes of the present document, the following symbols apply:
Δf The separation between the centre frequency of first or last 5 MHz channel used in the pass band
and the nominal -3 dB point of the measuring filter closest to the carrier frequency
Δf The largest value of Δf used for defining the requirement
max
F Filter centre frequency
filter
P Declared emission level for channel N
EM,
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.