SIST EN 3783:2014
(Main)Aerospace series - Fibre composite materials - Normalisation of fibre dominated mechanical properties
Aerospace series - Fibre composite materials - Normalisation of fibre dominated mechanical properties
This standard describes the procedure for normalisation of fibre dominated mechanical properties. The procedure is valid for carbon, glass and aramid reinforced laminates.
Luft- und Raumfahrt - Faserverbundwerkstoffe - Normierung von faserabhängigen mechanischen Eigenschaften
Diese Norm beschreibt das Verfahren für die Normierung von faserabhängigen mechanischen Eigenschaften. Das Verfahren gilt für kohlenstofffaser , glasfaser und aramidfaserverstärkte Laminate.
Série aérospatiale - Matériaux composites à base de fibres - Standardisation des caractéristiques mécaniques liées aux fibres
Aeronavtika - Kompozitni materiali z vlakni - Standardizacija mehanskih lastnosti materialov z večinskim deležem vlaken
General Information
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Luft- und Raumfahrt - Faserverbundwerkstoffe - Normierung von faserabhängigen mechanischen EigenschaftenSérie aérospatiale - Matériaux composites à base de fibres - Standardisation des caractéristiques mécaniques liées aux fibresAerospace series - Fibre composite materials - Normalisation of fibre dominated mechanical properties49.025.40Guma in polimerni materialiRubber and plasticsICS:Ta slovenski standard je istoveten z:EN 3783:2013SIST EN 3783:2014en01-marec-2014SIST EN 3783:2014SLOVENSKI
STANDARD
SIST EN 3783:2014
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 3783
August 2013 ICS 49.025.40 English Version
Aerospace series - Fibre composite materials - Normalisation of fibre dominated mechanical properties
Série aérospatiale - Matériaux composites à base de fibres - Standardisation des caractéristiques mécaniques liées aux fibres
Luft- und Raumfahrt - Faserverbundwerkstoffe - Normierung von faserabhängigen mechanischen Eigenschaften This European Standard was approved by CEN on 8 May 2013.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2013 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 3783:2013: ESIST EN 3783:2014
EN 3783:2013 (E) 2 Contents Page Foreword .3 1 Scope and field of application .4 2 Normative references .4 3 Principle .4 4 Designation .4 5 Procedure .5 6 Test report .6
SIST EN 3783:2014
EN 3783:2013 (E) 3 Foreword This document (EN 3783:2013) has been prepared by the Aerospace and Defence Industries Association of Europe - Standardization (ASD-STAN). After enquiries and votes carried out in accordance with the rules of this Association, this Standard has received the approval of the National Associations and the Official Services of the member countries of ASD, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by February 2014, and conflicting national standards shall be withdrawn at the latest by February 2014. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, R
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.