SIST EN 15386:2008
Packaging - Flexible laminate and plastic tubes - Test method to determine the print adhesion
Packaging - Flexible laminate and plastic tubes - Test method to determine the print adhesion
This standard specifies a method for the determination of the print adhesion on flexible laminate and plastic tubes. It is applicable to flexible laminate and plastic tubes used for packing pharmaceutical, cosmetic, hygiene, food and other household products.
Verpackung - Laminat- und Kunststofftuben - Prüfverfahren zur Bestimmung der Haftfestigkeit der Bedruckung
Emballage - Tubes souples plastiques et tubes souples laminés - Méthode d'essai pour déterminer l'adhérence de l'impression
Embalaža - Prožne laminatne in plastične tube - Preskusna metoda za ugotavljanje adhezije
General Information
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Packaging - Flexible laminate and plastic tubes - Test method to determine the print adhesionDGKH]LMHEmballage - Tubes souples plastiques et tubes souples laminés - Méthode d'essai pour déterminer l'adhérence de l'impressionVerpackung - Laminat- und Kunststofftuben - Prüfverfahren zur Bestimmung der Haftfestigkeit der BedruckungTa slovenski standard je istoveten z:EN 15386:2007SIST EN 15386:2008en,fr,de55.120ICS:SLOVENSKI
STANDARDSIST EN 15386:200801-februar-2008
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 15386November 2007ICS 55.120 English VersionPackaging - Flexible laminate and plastic tubes - Test method todetermine the print adhesionEmballage - Tubes souples plastiques et tubes soupleslaminés - Méthode d'essai pour déterminer l'adhérence del'impressionPackmittel - Laminat- und Kunststofftuben - Prüfverfahrenzur Bestimmung der Haftfestigkeit der BedruckungThis European Standard was approved by CEN on 30 September 2007.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2007 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 15386:2007: E
EN 15386:2007 (E) 2 Contents.page Foreword.3 1 Scope.4 2 Principle.4 3 Apparatus.4 4 Procedure.4 5 Test report.5 Annex A (normative)
Peel adhesion (180 °) at 300 mm/min.6
EN 15386:2007 (E) 3 Foreword This document (EN 15386:2007) has been prepared by Technical Committee CEN/TC 261 “Packaging”, the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by May 2008, and conflicting national standards shall be withdrawn at the latest by May 2008. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights. This standard is based on the professional recommendations of the European Tube Manufacturers Association (etma). According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom.
EN 15386:2007 (E) 4 1 Scope This standard specifies a method for the determination of the print adhesion on flexible laminate and plastic tubes. It is applicable to flexible laminate and plastic tubes used for packing pharmaceutical, cosmetic, hygiene, food and other household products. 2 Principle The adhesive tape test serves to gauge the adhesion properties of printing ink films on flexible laminate and plastic tubes.
The printing ink film is tested by rapidly tearing-off a previously applied adhesive tape. After the tape has been torn off, the divided surfaces are judged by pre-established criteria. 3 Apparatus An adhesive tape of commercial quality equipped with an upper surface made of tear-proof plastic and a pressure sensitive adhesive coating, of which the adhesive power is: minimum 5 N/25 mm and maximum 7 N/25 mm, tested according to Annex A against a glass testing surface. 4 Procedure
Place the printed sample on an even surface. Apply the adhesive tape on the sample and press it on manually across the length of the decoration.
It is important that there is full contact with the surface over the whole area and that no air bubbles remain between adhesive tape and sample surface. Approximately 10 s to 30 s after pressing-on, manually tear off the free end of the adhesive tape in one go from the surface at an angle of about 150 °.
Examine the divided surfaces (printing surface and reverse sid
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.