Loose-laid panels - Semi-rigid multilayer modular floor covering (MMF) panels with wear resistant top layer

This European Standard specifies the characteristics of semi-rigid multilayer modular floor covering with a wear-resistant and decorative surface layer supplied in panels (either tile or plank form). The floor panels are considered suitable for domestic and commercial levels of use and designed for floating installation.
This European Standard does not apply to resilient floor panels for loose-laying according to EN 14085, to multilayer wood floorings according to EN 13489, nor to products specified in EN ISO 10581, EN ISO 10582, EN ISO 24011, EN 12104 and ISO 14486.
This European Standard applies to areas which are subject to frequent wetting, e.g. bathrooms, laundry rooms or saunas, only if recommended by the producer.
This European Standard also includes requirements for marking and packaging.

Paneele für schwimmende Verlegung - Halbstarre, mehrlagige, modulare Fußbodenbeläge (MMF) mit abriebbeständiger Decklage

Panneaux pour pose flottante - Panneaux de revêtement de sol semi-rigides, multicouches et modulaires (MMF) avec couche supérieure résistante à l'usure

La présente Norme européenne spécifie les caractéristiques des revêtements de sol semi-rigides multicouches et modulaires, munis d'un parement décoratif et résistant à l'usure, fournis sous forme de panneaux (dalles ou lames). Ces panneaux de revêtement de sol sont considérés comme étant appropriés à des niveaux d’utilisation domestique et commerciale ; ils sont en outre conçus pour être mis en oeuvre en pose flottante.
La présente Norme européenne ne s'applique ni aux panneaux de revêtement de sol résilients pour pose flottante conformes à l'EN 14085, ni aux éléments de parquet contrecollés conformes à l'EN 13489, ni aux produits spécifiés dans les EN ISO 10581, EN ISO 10582, EN ISO 24011, EN 12104 et ISO 14486.
De même, elle ne s’applique aux lieux soumis à une humidification fréquente (par exemple, les salles de bain, les buanderies ou les saunas) que si le fabricant le revendique.
Enfin, la présente Norme européenne comprend également des exigences relatives au marquage et à l’emballage.

Prosto položene plošče - Večslojne poltoge talne obloge plošč z zgornjim delom, odpornim proti obrabi

Ta evropski standard določa lastnosti večplastnih poltogih modularnih talnih oblog z dekorativnim zgornjim delom, odpornim proti obrabi, dobavljenih v panelih (v obliki plošč ali trakov). Talne obloge so primerne za domačo in komercialno uporabo ter so zasnovane za plavajočo namestitev.
Ta evropski standard ne zajema odpornih talnih panelov za prosto polaganje v skladu s standardom EN 14085, večplastnih lesenih oblog v skladu s standardom EN 13489 oziroma izdelkov, opisanih v standardih EN ISO 10581, EN ISO 10582, EN ISO 24011, EN 12104 in ISO 14486.
Ta evropski standard zajema območja, ki so pogosto izpostavljena mokroti, npr. kopalnice, pralnice ali savne, le če tako priporoči proizvajalec.
Ta evropski standard vključuje tudi zahteve za označevanje in pakiranje.

General Information

Status
Withdrawn
Publication Date
09-May-2019
Withdrawal Date
28-May-2023
Current Stage
9900 - Withdrawal (Adopted Project)
Start Date
29-May-2023
Due Date
21-Jun-2023
Completion Date
29-May-2023

Relations

Buy Standard

Standard
EN 16511:2014+A1:2019
English language
11 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 16511:2014+A1:2019
01-junij-2019
Prosto položene plošče - Večslojne poltoge talne obloge plošč z zgornjim delom,
odpornim proti obrabi
Loose-laid panels - Semi-rigid multilayer modular floor covering (MMF) panels with wear
resistant top layer
Paneele für schwimmende Verlegung - Halbstarre, mehrlagige, modulare
Fußbodenbeläge (MMF) mit abriebbeständiger Decklage
Panneaux pour pose flottante - Panneaux de revêtement de sol semi-rigides,
multicouches et modulaires (MMF) avec couche supérieure résistante à l'usure
Ta slovenski standard je istoveten z: EN 16511:2014+A1:2019
ICS:
97.150 Talne obloge Floor coverings
SIST EN 16511:2014+A1:2019 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 16511:2014+A1:2019

---------------------- Page: 2 ----------------------

SIST EN 16511:2014+A1:2019


EN 16511:2014+A1
EUROPEAN STANDARD

NORME EUROPÉENNE

April 2019
EUROPÄISCHE NORM
ICS 97.150 Supersedes EN 16511:2014
English Version

Loose-laid panels - Semi-rigid multilayer modular floor
covering (MMF) panels with wear resistant top layer
Panneaux pour pose flottante - Panneaux de Paneele für schwimmende Verlegung - Halbstarre,
revêtement de sol semi-rigides, multicouches et mehrlagige, modulare Fußbodenbeläge (MMF) mit
modulaires (MMF) avec couche supérieure résistante à abriebbeständiger Decklage
l'usure
This European Standard was approved by CEN on 28 February 2014 and includes Amendment 1 approved by CEN on 8 February
2019.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 16511:2014+A1:2019 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN 16511:2014+A1:2019
EN 16511:2014+A1:2019 (E)
Contents Page
Foreword . 3
1 Scope . 4
2 Normative references . 4
3 Terms and definitions . 5
4 Requirements . 5
4.1 General requirements for the panels . 5
4.2 Classification requirements . 6
5 Marking and packaging . 9
5.1 Marking . 9
5.2 Packaging . 9
Annex A (informative) Optional properties . 10
Bibliography . 11

2

---------------------- Page: 4 ----------------------

SIST EN 16511:2014+A1:2019
EN 16511:2014+A1:2019 (E)
European foreword
This document (EN 16511:2014+A1:2019) has been prepared by Technical Committee CEN/TC 134
“Resilient, textile and laminate floor coverings”, the secretariat of which is held by NBN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by October 2019 and conflicting national standards shall
be withdrawn at the latest by October 2019.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent
rights.
This document includes Amendment 1 approved by CEN on 8 February 2019.
This document supersedes !EN 16511:2014".
The start and finish of text introduced or altered by amendment is indicated in the text by tags !".
According to the CEN-CENELEC Internal Regulations, the national standards organisations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
3

---------------------- Page: 5 ----------------------

SIST EN 16511:2014+A1:2019
EN 16511:2014+A1:2019 (E)
1 Scope
This European Standard specifies the characteristics of semi-rigid multilayer modular floor covering
with a wear-resistant and decorative surface layer supplied in panels (either tile or plank form). The
floor panels are considered suitable for domestic and commercial levels of use and designed for floating
installation.
This European Standard does not apply to resilient floor panels for loose-laying according to EN 14085,
to multilayer wood floorings according to EN 13489, nor to products specified in EN ISO 10581,
EN ISO 10582, EN ISO 24011, EN 12104 and ISO 14486.
This European Standard applies to areas which are subject to frequent wetting, e.g. bathrooms, laundry
rooms or saunas, only if recommended by the producer.
This European Standard also includes requirements for marking and packaging.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
EN 424, Resilient floor coverings - Determination of the effect of simulated movement of a furniture leg
!EN 425:2002", Resilient and laminate floor coverings - Castor chair test
EN 438-2, High-pressure decorative laminates (HPL) - Sheets based on thermosetting resins (usually called
Laminates) - Part 2: Determination of properties
EN 13329:2006+A1:2008, Laminate floor coverings - Elements with a surface layer based on aminoplastic
thermosetting resins - Specifications, requirements and test methods
EN 16094, Laminate floor coverings - Test method for the determination of micro-scratch resistance
!EN 15468:2016", Laminate floor coverings - Elements with directly applied printing and resin
surface layer - Specifications, requirements and test methods
EN ISO 10874, Resilient, textile and laminate floor coverings - Classification (ISO 10874)
EN ISO 23999, Resilient floor coverings - Determination of dimensional stability and curling after exposure
to heat (ISO 23999)
EN ISO 24343-1, Resilient and laminate floor coverings - Determination of indentation and residual
indentation - Part 1: Residual indentation (ISO 24343-1)
ISO 24334, Laminate floor coverings - Determination of locking strength for mechanically assembled
panels
ISO 24336, Laminate floor cov
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.