SIST EN ISO 3037:1996

Corrugated fibreboard - Determination of edgewise crush resistance (Unwaxed edge method) (ISO 3037:1994)

Wellpappe - Bestimmung des Kantenstauchwiderstandes (Verfahren für ungewachste Kanten) (ISO 3037:1994)

Diese Internationale Norm beschreibt ein Verfahren für die Bestimmung des Kantenstauchwiderstandes von Wellpappe. Es ist anwendbar für alle Wellpappe- Klassen.

Carton ondulé - Détermination de la résistance a la compression sur chant (Méthode sans enduction de cire) (ISO 3037:1994)

L’IEC 62969-4:2018 spécifie une méthode d’essai par injection directe de défaut pour l’interface à semiconducteurs des capteurs de véhicules automobiles, pouvant être utilisée pour assurer la conformité de l’interface de communication du véhicule.

Valoviti karton - Določanje robne odpornosti (metoda ECT)

General Information

• Status: Withdrawn
• Publication Date: 31-Mar-1996
• Withdrawal Date: 04-Jul-2007
• ICS: 85.060 - Paper and board
• Technical Committee: VPK - Pulp, paper, board and products
• Current Stage: 9900 - Withdrawal (Adopted Project)
• Start Date: 05-Jul-2007
• Due Date: 28-Jul-2007
• Completion Date: 05-Jul-2007
• Ref Project: EN ISO 3037:1996 - Corrugated fibreboard - Determination of edgewise crush resistance (Unwaxed edge method) (ISO 3037:1994)

Relations

• Replaced By: SIST EN ISO 3037:2007 - Corrugated fibreboard - Determination of edgewise crush resistance (unwaxed edge method) (ISO 3037:2007)
• Effective Date: 01-Jul-2007

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 3037:1996
01-april-1996
9DORYLWLNDUWRQ'RORþDQMHUREQHRGSRUQRVWLPHWRGD(&7
Corrugated fibreboard - Determination of edgewise crush resistance (Unwaxed edge
method) (ISO 3037:1994)
Wellpappe - Bestimmung des Kantenstauchwiderstandes (Verfahren für ungewachste
Kanten) (ISO 3037:1994)
Carton ondulé - Détermination de la résistance a la compression sur chant (Méthode
sans enduction de cire) (ISO 3037:1994)
Ta slovenski standard je istoveten z: EN ISO 3037:1996
ICS:
85.060 Papir, karton in lepenka Paper and board
SIST EN ISO 3037:1996 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

INTERNATIONAL
STANDARD
Third edition
1994-11-15
Corrugated fibreboard - Determination of
edgewise crush resistance (Unwaxed edge
method)
Carton onduk - Dgtermination de la rksistance 2 la compression sur
chant (M&hode sans enduction de tire)
Reference number
IS0 3037:1994(E)

---------------------- Page: 2 ----------------------

IS0 3037:1994(E)
Foreword
IS0 (the International Organization for Standardization) is a worldwide
federation of national standards bodies (IS0 member bodies). The work
of preparing International Standards is normally carried out through IS0
technical committees. Each member body interested in a subject for
which a technical committee has been established has the right to be
represented on that committee. International organizations, governmental
and non-governmental, in liaison with ISO, also take part in the work. IS0
collaborates closely with the International Electrotechnical Commission
(I EC) on all matters of electrotechnical standardization.
Draft International Standards adopted by the technical committees are
circulated to the member bodies for voting. Publication as an International
Standard requires approval by at least 75 % of the member bodies casting
a vote.
International Standard IS0 3037 was prepared by Technical Committee
ISOnC 6, Paper, board and pulps, Subcommittee SC 2, Test methods
and quality specifications for paper and board.
This third edition cancels and replaces the second edition (IS0 3037:1982),
of which it constitutes a technical revision.
0 IS0 1994
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced
or utilized in any form or by any means, electronic or mechanical, including photocopying and
microfilm, without permission in writing from the publisher.
International Organization for Standardization
Case Postale 56 l CH-1211 Geneve 20 l Switzerland
Printed in Switzerland
ii

---------------------- Page: 3 ----------------------

0 IS0
IS0 3037: 1994(E)
Introduction
A variety of methods for the determination of edgewise crush resistance
are in use in different parts of the world. These can be classified into three
groups as follows:
Those in which a carefully cut rectangular test piece is tested without
a)
any special treatment or modification.
Those in which the edges of the test piece to which the force is ap-
b)
plied are waxed to prevent the test result being influenced by “edge
effects “.
Those in which the test piece edges are not waxed but the shape of
d
the test piece is such that the length is substantially reduced at a point
midway between the loaded edges in order to induce the failure to
occur away from those edges.
The dimensions of the test piece vary from one group to the other and, in
group c), the methods vary in the shape and method of reducing the
length and in whether or not the test piece is held in a clamp during
crushing.
The methods may not give the same numerical results, but it can be
shown that most of them can be used to predict the top-to-bottom com-
pression strength which will be achieved when the board is properly con-
verted into a transport package.
This International Standard describes a method from group a). It is in-
tended as a method for quality measurement and quality specification
purposes and is selected because it correlates with the top-to-bottom
compression strength of the final transport package and because it is the
simplest and most operationally convenient method, an important factor
when large numbers of tests need to be conducted. However, it does not
measure the actual intrinsic compressive strength of the corrugated
fibreboard, giving lower results than most of the methods of groups b) and
c). This systematic difference is due to edge effects.
Other methods may be used for other purposes, particularly when the
object of the test is to study fundamental structural characteristics of the
package.
There are methods available for calculating the edgewise crush resistance
from the compression strength of the component papers.

---------------------- Page: 4 ----------------------

This page intentionally left blank

---------------------- Page: 5 ----------------------

IS0 3037: 1994(E)
INTERNATIONAL STANDARD 0 IS0
- Determination of edgewise
Corrugated fibreboard
crush resistance (Unwaxed edge method)
4 Apparatus
1 Scope
This International Standard specifies a method for the
4.1 Motor-driven, platen-type, crush tester
determination of edgewise crush resistance of corru-
gated fibreboard. It is applicable to all corrugated
The platens shall be large enough to take a test piece
fibreboard grades.
of the required size (see 7.2) and the guide blocks
(4.3) without any part of the test piece projecting be-
yond the edges of the platens.
2 Normative references
They shall be flat and also meet the following re-
quirements:
The following standards contain provisions which,
through reference in this text, constitute provisions
- deviation from parallel shall not be greater than
of this International Standard. At the time of publi-
1 :I 000 of the dimensions;
cation, the editions indicated were valid. All standards
are subject to revision, and parties to agreements
- lateral play shall not exceed 0,05 mm.
based on this International Standard are encouraged
to investigate the possibility of applying the most re-
NOTE 1 Because it is a requirement of other crush
cent editions of the standards indicated below.
methods, the platens may be faced with very fine emery
Members of IEC and IS0 maintain registers of cur-
paper, but where this is done, due regard should be paid to
rently valid International Standards.
maintaining the flatness and parallelism requirements pre-
scribed for the faces. However, it is preferable to use clean
unfaced platens when testing in accordance with this Inter-
IS0 186: 1994, Paper and board - Sampling to deter-
national Standard, and therefore it is advisable to provide
mine average quality.
two sets of platens, one unfaced and one faced with fine
emery paper, and to use whichever set is appropriate to the
IS0 187: 1990, Paper, board and pulps - Standard
test to be carried out.
atmosphere for conditioning and testing and pro-
cedure for monitoring the atmosphere and condition-
ing of samples.
4.1.1 If the tester operates with one fixed platen,
the other having a direct positive drive, the rate at
which platens approach each other shall be
12,5 mm/min + 2,5 mm/min. The tester shall be pro-
3 Principle
vided with a means of measuring the true peak force
to within 1 N.
Subjection of a rectangular test piece of the corru-
gated fibreboard, placed between the platens of a
4.1.2 If the tester operates on the principle of beam
crush tester with the flutes perpendicular to the sur-
deflection, the force applied by the platens shall be
faces of the platens, to a compressive force until fail-
developed at a rate of 110 N/s + 10 N/s when the
...