oSIST prEN ISO 8746:2024
(Main)Fasteners - Grooved pins with round head - Full-length diamond grooves (ISO/DIS 8746:2023)
Fasteners - Grooved pins with round head - Full-length diamond grooves (ISO/DIS 8746:2023)
Verbindungselemente - Halbrundkerbnägel (ISO/DIS 8746:2023)
Fixations - Clous cannelés à tête ronde - Cannelures diamant sur toute la longueur (ISO/DIS 8746:2023)
La présente Norme internationale prescrit les caractéristiques des clous cannelés à tête ronde, à trois cannelures constantes sur toute leur longueur, débouchantes d'un côté et régulièrement espacées, de diamètre nominal, d1, de 1,4 mm à 20 mm inclus. Le matériau refoulé de chaque côté des cannelures forme un renflement dont le diamètre d2, supérieur au diamètre nominal d1, permet un ajustement serré de ces clous cannelés lorsqu'ils sont emmanchés en force dans un trou de diamètre de perçage égal au diamètre nominal du clou d1 (voir article 4).
Vezni elementi - Zasekani zatiči z okroglo glavo - Diamantni utori po celotni dolžini (ISO/DIS 8746:2023)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
oSIST prEN ISO 8746:2024
01-februar-2024
Vezni elementi - Zasekani zatiči z okroglo glavo - Diamantni utori po celotni dolžini
(ISO/DIS 8746:2023)
Fasteners - Grooved pins with round head - Full-length diamond grooves (ISO/DIS
8746:2023)
Verbindungselemente - Halbrundkerbnägel (ISO/DIS 8746:2023)
Fixations - Clous cannelés à tête ronde - Cannelures diamant sur toute la longueur
(ISO/DIS 8746:2023)
Ta slovenski standard je istoveten z: prEN ISO 8746
ICS:
21.060.50 Zatiči, žeblji Pins, nails
oSIST prEN ISO 8746:2024 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN ISO 8746:2024
---------------------- Page: 2 ----------------------
oSIST prEN ISO 8746:2024
DRAFT INTERNATIONAL STANDARD
ISO/DIS 8746
ISO/TC 2 Secretariat: DIN
Voting begins on: Voting terminates on:
2023-11-29 2024-02-21
Fasteners — Grooved pins with round head — Full-length
diamond grooves
ICS: 21.060.50
This document is circulated as received from the committee secretariat.
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENT AND APPROVAL. IT IS
ISO/CEN PARALLEL PROCESSING
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/DIS 8746:2023(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION. © ISO 2023
---------------------- Page: 3 ----------------------
oSIST prEN ISO 8746:2024
ISO/DIS 8746:2023(E)
DRAFT INTERNATIONAL STANDARD
ISO/DIS 8746
ISO/TC 2 Secretariat: DIN
Voting begins on: Voting terminates on:
Fasteners — Grooved pins with round head — Full-length
diamond grooves
ICS: 21.060.50
This document is circulated as received from the committee secretariat.
COPYRIGHT PROTECTED DOCUMENT
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENT AND APPROVAL. IT IS
© ISO 2023
ISO/CEN PARALLEL PROCESSING
THEREFORE SUBJECT TO CHANGE AND MAY
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
NOT BE REFERRED TO AS AN INTERNATIONAL
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on STANDARD UNTIL PUBLISHED AS SUCH.
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
IN ADDITION TO THEIR EVALUATION AS
or ISO’s member body in the country of the requester. BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
ISO copyright office
USER PURPOSES, DRAFT INTERNATIONAL
CP 401 • Ch. de Blandonnet 8
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
CH-1214 Vernier, Geneva
POTENTIAL TO BECOME STANDARDS TO
Phone: +41 22 749 01 11
WHICH REFERENCE MAY BE MADE IN
Reference number
Email: copyright@iso.org
NATIONAL REGULATIONS.
Website: www.iso.org ISO/DIS 8746:2023(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
Published in Switzerland
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
ii
© ISO 2023 – All rights reserved
PROVIDE SUPPORTING DOCUMENTATION. © ISO 2023
---------------------- Page: 4 ----------------------
oSIST prEN ISO 8746:2024
ISO/DIS 8746:2023(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Principles of grooved pins and assembly . 2
5 Dimensions .
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.