SIST EN ISO 14344:2005
(Main)Welding and allied processes - Flux and gas shielded electrical welding processes - Procurement guidelines for consumables (ISO 14344:2002)
Welding and allied processes - Flux and gas shielded electrical welding processes - Procurement guidelines for consumables (ISO 14344:2002)
This standard is a tool for communication between a purchaser and a supplier of welding consumables within quality system as might, for example, be based upon EN ISO 9000.
Schweißen und verwandte Prozesse - Pulver- und gasgeschützte Schweißprozesse - Richtlinien zur Beschaffung von Schweißzusätzen (ISO 14344:2002)
Soudage et techniques connexes - Procédés de soudage électrique sous protection gazeuse et par flux - Lignes directrices relatives a l'approvisionnement en produits consommables (ISO 14344:2002)
Varjenje in sorodni postopki - Načini električnega varjenja pod praškom in v zaščitnih plinih - Smernice za nabavo dodajnih materialov (ISO 14344:2002)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 14344:2005
01-maj-2005
9DUMHQMHLQVRURGQLSRVWRSNL1DþLQLHOHNWULþQHJDYDUMHQMDSRGSUDãNRPLQY
]DãþLWQLKSOLQLK6PHUQLFH]DQDEDYRGRGDMQLKPDWHULDORY ,62
Welding and allied processes - Flux and gas shielded electrical welding processes -
Procurement guidelines for consumables (ISO 14344:2002)
Schweißen und verwandte Prozesse - Pulver- und gasgeschützte Schweißprozesse -
Richtlinien zur Beschaffung von Schweißzusätzen (ISO 14344:2002)
Soudage et techniques connexes - Procédés de soudage électrique sous protection
gazeuse et par flux - Lignes directrices relatives a l'approvisionnement en produits
consommables (ISO 14344:2002)
Ta slovenski standard je istoveten z: EN ISO 14344:2005
ICS:
25.160.20 Potrošni material pri varjenju Welding consumables
SIST EN ISO 14344:2005 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 14344:2005
---------------------- Page: 2 ----------------------
SIST EN ISO 14344:2005
EUROPEAN STANDARD
EN ISO 14344
NORME EUROPÉENNE
EUROPÄISCHE NORM
March 2005
ICS 25.160.20
English version
Welding and allied processes - Flux and gas shielded electrical
welding processes - Procurement guidelines for consumables
(ISO 14344:2002)
Soudage et techniques connexes - Procédés de soudage Schweißen und verwandte Prozesse - Pulver- und
électrique sous protection gazeuse et par flux - Lignes gasgeschützte Schweißprozesse - Richtlinien zur
directrices relatives à l'approvisionnement en produits Beschaffung von Schweißzusätzen (ISO 14344:2002)
consommables (ISO 14344:2002)
This European Standard was approved by CEN on 7 February 2005.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Central Secretariat or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2005 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 14344:2005: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 14344:2005
EN ISO 14344:2005 (E)
Foreword
The text of ISO 14344:2002 has been prepared by Technical Committee ISO/TC 44 "Welding
and allied processes" of the International Organization for Standardization (ISO) and has been
taken over as EN ISO 14344:2005 by Technical Committee CEN/TC 121 "Welding" the
secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of
an identical text or by endorsement, at the latest by September 2005, and conflicting national
standards shall be withdrawn at the latest by September 2005.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of
the following countries are bound to implement this European Standard: Austria, Belgium,
Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary,
Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Endorsement notice
The text of ISO 14344:2002 has been approved by CEN as EN ISO 14344:2005 without any
modifications.
2
---------------------- Page: 4 ----------------------
SIST EN ISO 14344:2005
INTERNATIONAL ISO
STANDARD 14344
First edition
2002-07-15
Welding and allied processes — Flux and
gas shielded electrical welding
processes — Procurement guidelines for
consumables
Soudage et techniques connexes — Procédés de soudage électrique sous
protection gazeuse et par flux — Lignes directrices relatives à
l'approvisionnement en produits consommables
Reference number
ISO 14344:2002(E)
©
ISO 2002
---------------------- Page: 5 ----------------------
SIST EN ISO 14344:2005
ISO 14344:2002(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not
be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this
file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this
area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters
were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event
that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2002
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic
or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body
in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.ch
Web www.iso.ch
Printed in Switzerland
ii © ISO 2002 – All rights reserved
---------------------- Page: 6 ----------------------
SIST EN ISO 14344:2005
ISO 14344:2002(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO
member bodies). The work of preparing International Standards is normally carried out through ISO technical
committees. Each member body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, governmental and non-governmental, in
liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical
Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3.
The main task of technical committees is to prepare International Standards. Draft International Standards adopted
by the technical committees are circulated to the member bodies for voting. Publication as an International
Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this International Standard may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights.
International Standard ISO 14344 was prepared in collaboration with the International Institute of Welding which
has been approved by the ISO Council as an international standardizing body in the field of welding.
© ISO 2002 – All rights reserved iii
---------------------- Page: 7 ----------------------
SIST EN ISO 14344:2005
---------------------- Page: 8 ----------------------
SIST EN ISO 14344:2005
INTERNATIONAL STANDARD ISO 14344:2002(E)
Welding and allied processes — Flux and gas shielded electrical
welding processes — Procurement guidelines for consumables
1 Scope
This International Standard is a tool for communication between a purchaser and a supplier of welding
consumables within quality systems as might, for example, be based upon ISO 9001. This International Standard,
together with an ISO or other recognized welding consumable standard, provides a method for preparing those
specific details needed for welding consumable procurement which consist of the following:
a) the welding consumable classification (selected from the pertinent ISO or other welding consumable standard);
b) the lot classification (selected from Clause 5 of this International Standard);
c) the testing schedule (selected from Clause 6 of this International Standard).
Selection of the specific welding consumable classification, lot classification and testing schedule will depend upon
the requirements of the application for which the welding consumable is being procured.
2 Normative reference
The following normative document contains provisions which, through reference in this text, constitute provisions of
this International Standard. For dated references, subsequent amendments to, or revisions of, any of this
publication do not apply. However, parties to agreements based on this International Standard are encouraged to
investigate the possibility of applying the most recent edition of the normative document indicated below. For
undated references, the latest edition of the normative document referred to applies. Members of ISO and IEC
maintain registers of currently valid International Standards.
ISO 9001, Quality management systems — Requirements
3 Terms and definitions
In production, the components of welding consumables are divided into discrete, predetermined quantities so that
satisfactory tests with a sample from that quantity will establish that the entire quantity meets specification
requirements. These quantities, known by such terms as heats, lots, blends, batches and mixes, vary in size
according to the manufacturer. For identification purposes, each manufacturer assigns a unique designation to
each quantity. This designation usually consists of a series of numbers or letters, or combinations thereof, which
will enable the manufacturer to determine the date and time (or shift) of manufacture, the type and source of the
raw materials used, and the details of the procedures used in producing the welding consumable. This designation
stays with the welding consumable and can be used to identify the material later, in those cases in which
identification is necessary.
For the purposes of this International Standard, the following terms and definitions apply.
3.1
dry batch
quantity of dry ingredients mixed at one time in one mixing vessel
© ISO 2002 – All rights reserved 1
---------------------- Page: 9 ----------------------
SIST EN ISO 14344:2005
ISO 14344:2002(E)
NOTE Liquid binder, when added to a dry batch, produces a wet mix. A dry batch may be divided into smaller quantities, in
which case addition of the liquid binder produces as many wet mixes as there were smaller quantities.
3.2
dry blend
two or more dry batches from which quantities of each are combined proportionately, then mixed in a mixing vessel
to produce a larger quantity in which the ingredients are as uniformly dispersed as they would have been had the
entire quantity been mixed together at one time in one large mixer
NOTE A dry blend, as in the case of a dry batch, may be used singly or divided into smaller quantities which, when the
liquid binder is added, produce one or more wet mixes.
3.3
wet mix
combination of liquid binder and a dry batch or dry blend, or a portion thereof, mixed at one time in one mixing
vessel
3.4
heat
for consumable inserts, solid electrodes and rods, core wire for covered electrodes, and the sheath (strip or tubing
of tubular cored electrode wire and rod), one of the following, depending on the method of melting and refining of
the metal:
the material obtained from one furnace melt, where slag-metal or gas-metal reactions occur in producing the
metal (e.g., open hearth, electric arc, basic oxygen, argon-oxygen processes);
an uninterrupted series of melts from one controlled batch of metals and alloying ingredients in one melting
furnace under the same melting conditions, each melt conforming to the chemical composition range approved
by the purchaser of the material (i.e., the producer of the welding consumable) where significant chemical
reactions do not occur in producing the metal (e.g., induction melting in a controlled atmosphere or in a
vacuum);
an uninterrupted series of remelts in one furnace under the same remelting conditions using one or more
consumable electrodes produced from a heat, as defined, each remelt conforming to the chemical composition
range approved by the purchaser of the material (i.e., the producer of the welding consumable) in processes
involving continuous melting and casting (e.g., consumable electrode remelt).
4 Identification
4.1 General
Identification of consumable inserts, solid electrode wire and strip, rods, core wire for covered electrodes, and the
sheath (strip or tubing) of tubular cored electrodes and rods shall be applied as listed in 4.2 to 4.5.
4.2 Heat Number
Solid wire, electrode core wire, rod, strip and consumable inserts, identified by heat number, shall consist of
material from a single heat of metal.
4.3 Controlled chemical composition
Solid wire, electrode core wire, rod, strip and consumable inserts identified by controlled chemical composition,
rather than by heat number, shall consist of mill coils of one or more heats from which samples have been taken for
chemical analysis. The results of the analysis of each sample shall be within the
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.