iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
SIST

oSIST prEN ISO 19085-4:2021

(Main)

Woodworking machines - Safety - Part 4: Vertical panel circular sawing machines (ISO/DIS 19085-4:2021)

Woodworking machines - Safety - Part 4: Vertical panel circular sawing machines (ISO/DIS 19085-4:2021)

DPW = DAV + 24

Holzbearbeitungsmaschinen - Sicherheit - Teil 4: Vertikalplattenkreissägemaschinen (ISO/DIS 19085-4:2021)

Dieses Dokument beschreibt Sicherheitsanforderungen und Maßnahmen für Vertikalplattenkreissäge-maschinen mit Handbeschickung und Handentnahme, wie in 3.1 definiert, die für den dauerhaften Einsatz in der Produktion geeignet sind und im Folgenden als "Maschinen" bezeichnet werden.
Es behandelt alle im Anhang A aufgeführten signifikanten Gefährdungen, Gefährdungssituationen und Gefährdungsereignisse, die auf die Maschinen zutreffen, wenn sie bestimmungsgemäß und entsprechend den vom Hersteller vorhergesehenen Bedingungen verwendet, eingestellt und gewartet werden, einschließlich des vernünftigerweise vorhersehbaren Fehlgebrauchs. Ferner wurden die Phasen Transport, Montage, Demontage, Rückbau und Verschrottung berücksichtigt.
Es gilt auch für Maschinen, die mit einer oder mehrerer der folgenden Einrichtungen/zusätzlichen Arbeitsaggregaten, deren Gefährdungen behandelt wurden, ausgerüstet sind:
- eine mechanische Vorschubeinrichtung;
- eine Einrichtung zum Ritzsägen;
- eine Winkelschnitteinrichtung;
- eine Mittenauflage;
- programmierbare Endanschläge für senkrechte Parallelschnitte;
- eine Einrichtung zum Nuten bis zu einer Breite von höchstens 20 mm in einem Durchgang unter Verwendung eines Fräswerkzeugs; und
- ein Plattenschieber.
Die Maschinen sind gestaltet zum Schneiden von Platten bestehend aus:
a) Massivholz;
b) Werkstoffen mit ähnlichen physikalischen Eigenschaften wie Holz (siehe ISO 19085-1:2021, 3.2);
c) Verbundwerkstoffen mit einem Kern zum Beispiel aus Polyurethan oder mineralischem Werkstoff, mit Leichtmetallbeschichtung;
d) Polymer-Matrix-Verbundwerkstoffe und faserverstärkte Thermoplast-/Duroplast-/Elastomer-Werkstoffe;
e) Gipskartonplatten, gipsgebundene Faserplatten.
Dieses Dokument gilt nicht für Maschinen
- mit Druckbalken, bei denen das Sägeaggregat hinter der Werkstückauflage angeordnet ist;
- bei denen die Führungsschienen, auf denen sich das Sägeaggregat senkrecht bewegt, am Maschinengestell befestigt sind und der waagerechte Schnitt nur durch Zuführen der Platte von Hand erfolgen kann;
- die nur zum Schneiden in senkrechter Richtung gestaltet sind;
- die zwei oder mehr Schnittzyklen automatisch in Folge durchführen;
- die zur bestimmungsgemäßen Verwendung in potentiell explosiver Atmosphäre vorgesehen sind; und
- die vor dem Datum seiner Veröffentlichung hergestellt wurden.

Machines à bois - Sécurité - Partie 4: Scies circulaires à panneaux verticales (ISO/DIS 19085-4:2021)

Lesnoobdelovalni stroji - Varnost - 4. del: Krožne žage z vertikalno ploščo (ISO/DIS 19085-4:2021)

General Information

Status
Not Published
Public Enquiry End Date
19-Sep-2021
ICS
13.110 - Safety of machinery
25.080.60 - Sawing machines
79.120.10 - Woodworking machines
Technical Committee
VSN - Safety of machinery
Current Stage
5020 - Formal vote (FV) (Adopted Project)
Start Date
06-Mar-2024
Due Date
24-Apr-2024
Directive
2006/42/EC - Directive 2006/42/EC of the European Parliament and of the Council of 17 May 2006 on machinery, and amending Directive 95/16/EC (recast)
Mandate
M/396 - Mandate to CEN and Cenelec for standardisation in the field of machinery
Ref Project
FprEN ISO 19085-4 - Woodworking machines - Safety - Part 4: Vertical panel circular sawing machines (ISO/FDIS 19085-4:2024)

Relations

Revised
SIST EN ISO 19085-4:2018 - Woodworking machines - Safety - Part 4: Vertical panel circular sawing machines (ISO 19085-4:2018)
Effective Date
19-Jan-2023
Revised
SIST EN ISO 19085-4:2018 - Woodworking machines - Safety - Part 4: Vertical panel circular sawing machines (ISO 19085-4:2018)
Effective Date
18-Jan-2023
Revised
SIST EN ISO 19085-4:2018 - Woodworking machines - Safety - Part 4: Vertical panel circular sawing machines (ISO 19085-4:2018)
Effective Date
05-May-2021

Buy Standard

prEN ISO 19085-4:2021prEN ISO 19085-4:2021
PreviousNext
Draft
prEN ISO 19085-4:2021
English language
41 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
oSIST prEN ISO 19085-4:2021
01-september-2021
Lesnoobdelovalni stroji - Varnost - 4. del: Krožne žage z vertikalno ploščo (ISO/DIS
19085-4:2021)
Woodworking machines - Safety - Part 4: Vertical panel circular sawing machines
(ISO/DIS 19085-4:2021)
Holzbearbeitungsmaschinen - Sicherheit - Teil 4: Vertikalplattenkreissägemaschinen
(ISO/DIS 19085-4:2021)
Machines à bois - Sécurité - Partie 4: Scies circulaires à panneaux verticales (ISO/DIS
19085-4:2021)
Ta slovenski standard je istoveten z: prEN ISO 19085-4
ICS:
13.110 Varnost strojev Safety of machinery
25.080.60 Strojne žage Sawing machines
79.120.10 Lesnoobdelovalni stroji Woodworking machines
oSIST prEN ISO 19085-4:2021 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN ISO 19085-4:2021

---------------------- Page: 2 ----------------------
oSIST prEN ISO 19085-4:2021
DRAFT INTERNATIONAL STANDARD
ISO/DIS 19085-4
ISO/TC 39/SC 4 Secretariat: UNI
Voting begins on: Voting terminates on:
2021-07-06 2021-09-28
Woodworking machines — Safety —
Part 4:
Vertical panel circular sawing machines
Machines à bois — Sécurité —
Partie 4: Scies circulaires à panneaux verticales
ICS: 13.110; 79.120.10
THIS DOCUMENT IS A DRAFT CIRCULATED
This document is circulated as received from the committee secretariat.
FOR COMMENT AND APPROVAL. IT IS
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
ISO/CEN PARALLEL PROCESSING
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/DIS 19085-4:2021(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
©
PROVIDE SUPPORTING DOCUMENTATION. ISO 2021

---------------------- Page: 3 ----------------------
oSIST prEN ISO 19085-4:2021
ISO/DIS 19085-4:2021(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2021
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2021 – All rights reserved

---------------------- Page: 4 ----------------------
oSIST prEN ISO 19085-4:2021
ISO/DIS 19085-4:2021(E)

Contents Page
Foreword .v
Introduction .vi
1 Scope . 1
2 Normative references . 2
3 Terms and definitions . 2
4 Safety requirements and measures for controls . 5
4.1 Safety and reliability of control systems . 5
4.2 Control devices . 5
4.3 Start . 5
4.3.1 Direct start .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

SIST
SIST EN ISO 19085-16:2022(Main)
Woodworking machines - Safety - Part 16: Table band saws and band re-saws (ISO 19085-16:2021)
EN ISO 19085-16:2021

This document gives the safety requirements and measures for stationary and displaceable table band saws and band resaws with manual loading and/or unloading, designed to cut wood and materials with similar physical characteristics to wood, hereinafter referred to as “machines”.
NOTE 1   For the definition of displaceable machine, see ISO 19085-1:2017, 3.5.
It deals with all significant hazards, hazardous situations and events as listed in Clause 4, relevant to the machines, when operated, adjusted and maintained as intended and under the conditions foreseen by the manufacturer including reasonably foreseeable misuse. Also, transport, assembly, dismantling, disabling and scrapping phases have been taken into account.
NOTE 2   For relevant but not significant hazards, e.g. sharp edges of the machine frame, see ISO 12100:2010.
It is also applicable to machines fitted with one or more of the following devices/additional working units, whose hazards have been dealt with:
a)   device to tilt the table;
b)   device to tilt the saw unit.
This document does not apply to:
1)   machines driven by combustion engines or power take offs (PTO);
2)   log band sawing machines;
NOTE 3   Log band sawing machines are covered by EN 1807-2.
3)   machines designed for cross-cutting round or irregular shaped work-pieces;
4)   transportable / displaceable machines with a maximum length of the band saw blade of ≤ 2700 mm and a maximum diameter of the powered wheel of ≤ 350 mm;
NOTE 4    Transportable electrically driven machines are covered by the requirements of EN 61029-1:2009 together with EN 61029-2-5:2015.

  • Standard
    45 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    45 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 19085-2:2022(Main)
Woodworking machines - Safety - Part 2: Horizontal beam panel circular sawing machines (ISO 19085-2:2021)
EN ISO 19085-2:2021

This document gives the safety requirements and measures for horizontal beam panel circular sawing machines with the saw carriage of the front cutting line mounted below the workpiece support, which are manually and/or powered loaded and manually unloaded, capable of continuous production use, as defined in 3.1 and hereinafter referred to as “machines”.
This document deals with all significant hazards, hazardous situations and events as listed in Annex A, relevant to the machines, when operated, adjusted and maintained as intended and under the conditions foreseen by the manufacturer including reasonably foreseeable misuse. Also, transport, assembly, dismantling, disabling and scrapping phases have been taken into account.
It is also applicable to machines fitted with one or more of the following devices/additional working units, whose hazards have been dealt with:
—    side pressure device;
—    device for powered unloading;
—    unit for scoring;
—    unit for post-formed/soft-formed edge pre-cutting;
—    panel turning device;
—    front side turn table;
—    pushing out device;
—    pneumatic clamping of the saw blade;
—    powered panel loading device;
—    device for grooving by milling tool;
—    one or more additional cutting lines inside the machine for longitudinal and/or head cut (before the transversal cutting line);
—    workpiece vacuum clamping as part of a front side turn table or of a panel loading device;
—    panel pusher;
—    independent panel pushers;
—    additional panel pushers mounted on the panel pusher carriage;
—    additional panel pusher with integrated label printer device;
—    lifting platform;
—    device for automatic loading of thin panels;
—    device for base board unloading by gravity;
—    device for base board powered unloading;
—    device for panel unloading in limited space condition;
—    loading or pre-loading roller conveyors;
—    pressure beam with additional flaps to increase dust extraction efficiency;
—    saw blade cooling system by air or water-air or oil-air;
—    vibrating conveyor with/without trimming unit for offcuts management;
—    predisposition for top loading/unloading by an external system directly on the machine table and/or on the machine preloading roller conveyor and/or on the machine lifting table.
NOTE      base board is a support panel underlying the panel stack, to protect the panels from damages during transportation.
The machines are designed for cutting panels consisting of:
a) solid wood;
b) material with similar physical characteristics to wood (see ISO19085‑1:2021, 2);
c) gypsum boards, gypsum bounded fibreboards;
d) composite materials, with core consisting of e.g. polyurethane or mineral material, laminated with light alloy;
e) cardboard;
f) foam board;
g) matrix engineered mineral boards, silicate boards;
h) polymer‐matrix composite materials and reinforced thermoplastic/thermoset/elastomeric materials;
i) aluminium light alloy plates with a maximum thickness of 10 mm;
j) composite boards made from the materials listed above.
This document does not deal with hazards related to:
—    specific features different from those listed above;
—    the machining of panels with milling tools for grooving;
—    powered unloading of panels;
—    rear half of split pressure beam on the front cutting line;
—    the combination of a single machine being used with any other machine (as part of a line).
It is not applicable to:
—    machines intended for use in potentiall

  • Standard
    56 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    50 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 19085-10:2019/A11:2021(Amendment)
Woodworking machines - Safety - Part 10: Building site saws (contractor saws) (ISO 19085-10:2018, including Corrected version 2019-12)
EN ISO 19085-10:2019/A11:2020

2020-07-20 JF: Through the decision C132/2020 taken on 2020-07-08, the CEN Technical Board approved the revised Annex ZA and therefore, the European Amendment, of EN ISO 19085-10:2019. European amendment is under publication.

  • Amendment
    6 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 19085-13:2020(Main)
Woodworking machines - Safety - Part 13: Multi-blade rip sawing machines with manual loading and/or unloading (ISO 19085-13:2020)
EN ISO 19085-13:2020

This international standard deals with all significant hazards, hazardous situations and events relevant to stationary multi-blade rip sawing machines, hereinafter referred to as “machines”, designed to cut solid wood and material with similar physical characteristics as wood, when operated, adjusted and maintained as intended and under the conditions foreseen by the manufacturer including reasonably foreseeable misuse. Also transport, assembly, dismantling, disabling and scrapping phases are taken into account.
This international standard does not apply to machines with vertical roller feed or vertical chain conveyor feed or machines designed to make the first rip cut on a log.
This international standard does not deal with specific hazards related to the combination of single machines with any other machine as part of a line.

  • Standard
    52 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    54 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 19085-9:2020(Main)
Woodworking machines - Safety - Part 9: Circular saw benches (with and without sliding table) (ISO 19085-9:2019)
EN ISO 19085-9:2020

This international standard deals with all significant hazards, hazardous situations and events as listed in Clause 4 which are relevant to stationary and displaceable circular saw benches (with or without sliding table and/or demountable power feed unit), also known as “table saws” (in the USA), hereinafter referred to as “machines”, designed to cut wood and material with similar physical characteristics to wood, when they are operated, adjusted and maintained as intended and under the conditions foreseen by the manufacturer including reasonably foreseeable misuse. Also transport, assembly, dismantling, disabling and scrapping phases are taken into account.

  • Standard
    60 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
oSIST prEN ISO 19085-9:2022(Main)
Woodworking machines - Safety - Part 9: Circular saw benches (with and without sliding table) (ISO/DIS 19085-9:2022)
prEN ISO 19085-9

This document specifies the safety requirements and measures for circular saw benches with or without sliding table and/or demountable power feed unit and capable of continuous production use, also known as “table saws” (in the USA), hereinafter referred to also as “machines”.
The machines are designed to cut wood and material with similar physical characteristics to wood.
It deals with all significant hazards, hazardous situations and events as listed in Annex A relevant to the machines when operated, adjusted and maintained as intended and under the conditions foreseen by the manufacturer; reasonably foreseeable misuse has been considered too. Transport, assembly, dismantling, disabling and scrapping phases have also been taken into account.
It is also applicable to machines fitted with one or more of the following devices, or working unit, whose hazards have been dealt with:
— device for the main saw blade and scoring saw blade to be raised and lowered through the table;
— device to tilt the main saw blade and scoring saw blade for angled cutting;
— device for scoring;
— device for grooving with milling tool with a width not exceeding 20 mm in one pass;
— demountable power feed unit;
— additional manually operated sliding table;
— powered workpiece clamping device.
This document does not apply to:
a) machines intended for outdoor use on building sites;
NOTE 1   Building site saws (contractor saws) are covered by the requirements of ISO 19085 10:2018.
b) handheld woodworking machines including any adaptation permitting their use in a different mode, i.e., bench mounting;
c) machines intended for use in a potentially explosive atmosphere;
d) machines manufactured prior to the date of its publication as an International Standard.

  • Draft
    59 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
oSIST prEN ISO 19085-13:2023(Main)
Woodworking machines - Safety - Part 13: Multi-blade rip sawing machines with manual loading and/or unloading (ISO/DIS 19085-13:2022)
prEN ISO 19085-13

This document specifies the safety requirements and measures for multi-blade rip sawing machines with manual loading and/or unloading (defined in 3.1) capable of continuous production use, hereinafter referred to also as “machines”, designed to cut solid wood and materials with similar physical characteristics to wood.
It deals with all significant hazards, hazardous situations and events as listed in Annex A, relevant to the machines, when operated, adjusted and maintained as intended and under the conditions foreseen by the manufacturer including reasonably foreseeable misuse. Transport, assembly, dismantling, disabling and scrapping phases are also taken into account.
This document does not deal with specific hazards related to the combination of single machines with any other machine as part of a line.
It is not applicable to machines:
— with all saw blades spindles mounted below the workpiece support/level only;
— intended for use in potentially explosive atmosphere;
— manufactured prior to its publication.

  • Draft
    51 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
kSIST FprEN ISO 19085-5:2024(Main)
Woodworking machines - Safety - Part 5: Dimension saws (ISO/FDIS 19085-5:2024)
FprEN ISO 19085-5

DOW = DAV + 24

  • Draft
    66 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 19085-16:2022(Main)
Woodworking machines - Safety - Part 16: Table band saws and band re-saws (ISO 19085-16:2021)
EN ISO 19085-16:2021

This document gives the safety requirements and measures for stationary and displaceable table band saws and band resaws with manual loading and/or unloading, designed to cut wood and materials with similar physical characteristics to wood, hereinafter referred to as “machines”.
NOTE 1   For the definition of displaceable machine, see ISO 19085-1:2017, 3.5.
It deals with all significant hazards, hazardous situations and events as listed in Clause 4, relevant to the machines, when operated, adjusted and maintained as intended and under the conditions foreseen by the manufacturer including reasonably foreseeable misuse. Also, transport, assembly, dismantling, disabling and scrapping phases have been taken into account.
NOTE 2   For relevant but not significant hazards, e.g. sharp edges of the machine frame, see ISO 12100:2010.
It is also applicable to machines fitted with one or more of the following devices/additional working units, whose hazards have been dealt with:
a)   device to tilt the table;
b)   device to tilt the saw unit.
This document does not apply to:
1)   machines driven by combustion engines or power take offs (PTO);
2)   log band sawing machines;
NOTE 3   Log band sawing machines are covered by EN 1807-2.
3)   machines designed for cross-cutting round or irregular shaped work-pieces;
4)   transportable / displaceable machines with a maximum length of the band saw blade of ≤ 2700 mm and a maximum diameter of the powered wheel of ≤ 350 mm;
NOTE 4    Transportable electrically driven machines are covered by the requirements of EN 61029-1:2009 together with EN 61029-2-5:2015.

  • Standard
    45 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    45 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 19085-2:2022(Main)
Woodworking machines - Safety - Part 2: Horizontal beam panel circular sawing machines (ISO 19085-2:2021)
EN ISO 19085-2:2021

This document gives the safety requirements and measures for horizontal beam panel circular sawing machines with the saw carriage of the front cutting line mounted below the workpiece support, which are manually and/or powered loaded and manually unloaded, capable of continuous production use, as defined in 3.1 and hereinafter referred to as “machines”.
This document deals with all significant hazards, hazardous situations and events as listed in Annex A, relevant to the machines, when operated, adjusted and maintained as intended and under the conditions foreseen by the manufacturer including reasonably foreseeable misuse. Also, transport, assembly, dismantling, disabling and scrapping phases have been taken into account.
It is also applicable to machines fitted with one or more of the following devices/additional working units, whose hazards have been dealt with:
—    side pressure device;
—    device for powered unloading;
—    unit for scoring;
—    unit for post-formed/soft-formed edge pre-cutting;
—    panel turning device;
—    front side turn table;
—    pushing out device;
—    pneumatic clamping of the saw blade;
—    powered panel loading device;
—    device for grooving by milling tool;
—    one or more additional cutting lines inside the machine for longitudinal and/or head cut (before the transversal cutting line);
—    workpiece vacuum clamping as part of a front side turn table or of a panel loading device;
—    panel pusher;
—    independent panel pushers;
—    additional panel pushers mounted on the panel pusher carriage;
—    additional panel pusher with integrated label printer device;
—    lifting platform;
—    device for automatic loading of thin panels;
—    device for base board unloading by gravity;
—    device for base board powered unloading;
—    device for panel unloading in limited space condition;
—    loading or pre-loading roller conveyors;
—    pressure beam with additional flaps to increase dust extraction efficiency;
—    saw blade cooling system by air or water-air or oil-air;
—    vibrating conveyor with/without trimming unit for offcuts management;
—    predisposition for top loading/unloading by an external system directly on the machine table and/or on the machine preloading roller conveyor and/or on the machine lifting table.
NOTE      base board is a support panel underlying the panel stack, to protect the panels from damages during transportation.
The machines are designed for cutting panels consisting of:
a) solid wood;
b) material with similar physical characteristics to wood (see ISO19085‑1:2021, 2);
c) gypsum boards, gypsum bounded fibreboards;
d) composite materials, with core consisting of e.g. polyurethane or mineral material, laminated with light alloy;
e) cardboard;
f) foam board;
g) matrix engineered mineral boards, silicate boards;
h) polymer‐matrix composite materials and reinforced thermoplastic/thermoset/elastomeric materials;
i) aluminium light alloy plates with a maximum thickness of 10 mm;
j) composite boards made from the materials listed above.
This document does not deal with hazards related to:
—    specific features different from those listed above;
—    the machining of panels with milling tools for grooving;
—    powered unloading of panels;
—    rear half of split pressure beam on the front cutting line;
—    the combination of a single machine being used with any other machine (as part of a line).
It is not applicable to:
—    machines intended for use in potentiall

  • Standard
    56 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    50 pages
    English language
    sale 10% off
    e-Library read for
    1 day