SIST EN 4425:2009
(Main)Aerospace series - Washers, tab in corrosion resisting steel for flight control rods - Dimensions
Aerospace series - Washers, tab in corrosion resisting steel for flight control rods - Dimensions
This standard specifies the characteristics of tab washers for flight control rods.
These tab washers are intended to immobilise the rod end in relation to the rod body, whilst allowing a positional adjustment.
Luft- und Raumfahrt - Sicherungsbleche aus korrosionsbeständigem Stahl, für Bediengestänge von Flugsteuerungen - Maße
Diese Norm legt die Eigenschaften von Sicherungsblechen für Bediengestänge von Flugsteuerungen fest.
Diese Sicherungsbleche dienen dazu, den Stangenkopf gegenüber dem Rohrkörper zu arretieren und gleichzeitig eine Lageeinstellung zu ermöglichen.
Série aérospatiale - Freins d'écrous en acier résistant à la corrosion pour bielles de commandes de vol - Dimensions
Aeronavtika - Podložke z zavihkom iz korozijsko odpornega jekla za kontrolne palice pri krmiljenju - Mere
General Information
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Aeronavtika - Podložke z zavihkom iz korozijsko odpornega jekla za kontrolne palice pri krmiljenju - MereLuft- und Raumfahrt - Sicherungsbleche aus korrosionsbeständigem Stahl, für Bediengestänge von Flugsteuerungen - MaßeSérie aérospatiale - Freins d'écrous en acier résistant à la corrosion pour bielles de commandes de vol - DimensionsAerospace series - Washers, tab in corrosion resisting steel for flight control rods - Dimensions49.030.50Podložke in drugi blokirni elementiWashers and other locking elementsICS:Ta slovenski standard je istoveten z:EN 4425:2006SIST EN 4425:2009en,de01-junij-2009SIST EN 4425:2009SLOVENSKI
STANDARD
SIST EN 4425:2009
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 4425June 2006ICS 49.030.50 English VersionAerospace series - Washers, tab in corrosion resisting steel forflight control rods - DimensionsSérie aérospatiale - Freins d'écrous en acier résistant à lacorrosion pour bielles de commandes de vol - DimensionsLuft- und Raumfahrt - Sicherungsbleche auskorrosionsbeständigem Stahl, für Bediengestänge vonFlugsteuerungen - MaßeThis European Standard was approved by CEN on 20 April 2006.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2006 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 4425:2006: ESIST EN 4425:2009
EN 4425:2006 (E) 2 Contents Page Foreword.3 1 Scope.4 2 Normative references.4 3 Required characteristics.4 4 Designation.6 5 Marking.6 6 Qualification.6
SIST EN 4425:2009
EN 4425:2006
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.