SIST EN 3711:2008

Aerospace series - Wrench-double ended, bi-hexagonal - Straight, cranked, offset

This standard specifies the properties of the following types of double end box wrenches: double head flat, double head offset and double end modified offset.

Luft- und Raumfahrt - Doppelringschlüssel, Doppelsechskant - Gerade, abgewinkelt, flach gekröpft

Diese Norm legt die Eigenschaften der folgenden Ausführungen von Doppelringschlüsseln fest: gerade, abgewinkelt und flach gekröpft.

Série aérospatiale - Clé bihexagonale, double, droite, inclinée, contre coudée

Aeronavtika - Ključi za vijake - Obojestranski, biheksagonalni - Ravni, kolenasti, zviti

General Information

• Status: Published
• Publication Date: 26-May-2008
• ICS: 49.030.99 - Other fasteners
• Technical Committee: I13 - Imaginarni 13
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 09-May-2008
• Due Date: 14-Jul-2008
• Completion Date: 27-May-2008
• Ref Project: EN 3711:2008 - Aerospace series - Wrench-double ended, bi-hexagonal - Straight, cranked, offset

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.]YLWLLuft- und Raumfahrt - Doppelringschlüssel, Doppelsechskant - Gerade, abgewinkelt, flach gekröpftSérie aérospatiale - Clé bihexagonale, double, droite, inclinée, contre coudéeAerospace series - Wrench-double ended, bi-hexagonal - Straight, cranked, offset49.030.99Drugi vezni elementiOther fastenersICS:Ta slovenski standard je istoveten z:EN 3711:2008SIST EN 3711:2008en01-julij-2008SIST EN 3711:2008SLOVENSKI
STANDARD



SIST EN 3711:2008



EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 3711April 2008ICS 25.140.30 English VersionAerospace series - Wrench-double ended, bi-hexagonal -Straight, cranked, offsetSérie aérospatiale - Clé bihexagonale, double, droite,inclinée, contre coudéeLuft- und Raumfahrt - Doppelringschlüssel,Doppelsechskant - Gerade, abgewinkelt, flach gekröpftThis European Standard was approved by CEN on 21 December 2007.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2008 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 3711:2008: ESIST EN 3711:2008



EN 3711:2008 (E) 2 Contents Page Foreword.3 1 Scope.4 2 Normative references.4 3 Requirements.4 3.1 Configuration, dimensions, tolerances.4 3.2 Material.4 3.3 Hardness.4 3.4 Surface treatment.4 4 Designation.6 5 Marking.7 6 Technical specification.7
Figures Figure 1 — Box wrench flat.5 Figure 2 — Box wrench 15° offset.
...