SIST ISO 16000-3:2012
Indoor air - Part 3: Determination of formaldehyde and other carbonyl compounds in indoor air and test chamber air - Active sampling method
Indoor air - Part 3: Determination of formaldehyde and other carbonyl compounds in indoor air and test chamber air - Active sampling method
This part of ISO 16000 specifies a determination of formaldehyde (HCHO) and other carbonyl compounds (aldehydes and ketones) in air. The method is specific to formaldehyde but, with modification, at least 12 other aromatic as well as saturated and unsaturated aliphatic carbonyl compounds (see last paragraph) can be detected and quantified. It is suitable for determination of formaldehyde and other carbonyl compounds in the approximate concentration range 1 µg/m3 to 1 mg/m3. The sampling method gives a time-weighted average (TWA) sample. It can be used for long-term (1 h to 24 h) or short-term (5 min to 60 min) sampling of air for formaldehyde.
This part of ISO 16000 specifies a sampling and analysis procedure for formaldehyde and other carbonyl compounds that involves collection from air on to adsorbent cartridges coated with 2,4-dinitrophenylhydrazine (DNPH) and subsequent analysis of the hydrazones formed by high performance liquid chromatography (HPLC) with detection by ultraviolet absorption.
This part of ISO 16000 applies to the determination of: formaldehyde; acetaldehyde; acetone; benzaldehyde; butyraldehyde; valeraldehyde; 2,5-dimethylbenzaldehyde; capronaldehyde; isovaleraldehyde; propionaldehyde; o-tolualdehyde; m-tolualdehyde; p-tolualdehyde.
Air intérieur - Partie 3: Dosage du formaldéhyde et d'autres composés carbonylés dans l'air intérieur et dans l'air des chambres d'essai - Méthode par échantillonnage actif
L'ISO 16000-3:2011 spécifie un dosage du formaldéhyde (HCHO) et d'autres composés carbonylés (aldéhydes et cétones) dans l'air. La méthode est spécifique au formaldéhyde. Toutefois, si elle est modifiée, au moins 12 autres composés carbonylés (voir dernier alinéa) peuvent être détectés et quantifiés. Elle convient au dosage du formaldéhyde et d'autres composés carbonylés dans la plage de concentration comprise entre environ 1 µg/m3 et 1 mg/m3. La méthode d'échantillonnage fournit un résultat moyen pondéré dans le temps (TWA). Elle peut être utilisée pour l'échantillonnage du formaldéhyde dans l'air à long terme (1 h à 24 h) ou à court terme (5 min à 60 min).
L'ISO 16000-3:2011 spécifie un mode opératoire d'échantillonnage et d'analyse pour le formaldéhyde et d'autres composés carbonylés qui implique un prélèvement de l'air sur des cartouches imprégnées de 2,4-dinitrophénylhydrazine (DNPH) et une analyse ultérieure par chromatographie en phase liquide à haute performance (CLHP) avec détection par absorption ultraviolette.
L'ISO 16000-3:2011 est applicable au dosage des composés suivants: formaldéhyde, acétaldéhyde, acétone, benzaldéhyde, butyraldéhyde, valéraldéhyde, 2,5-diméthylbenzaldéhyde, capronaldéhyde, isovaléraldéhyde, propionaldéhyde, o-tolualdéhyde, m-tolualdéhyde, p-tolualdéhyde.
Notranji zrak - 3. del: Določevanje formaldehida in drugih karbonilnih spojin v notranjem zraku in zraku v preskusnih komorah - Metoda aktivnega vzorčenja
Ta del standarda ISO 16000 določa ugotavljanje formaldehida (HCHO) in drugih karbonilnih spojin (aldehidov in ketonov) v zraku. Metoda je specifična za formaldehid, vendar se lahko s spremembami uporablja za določevanje in kvantifikacijo najmanj 12 drugih aromatskih, nasičenih in nenasičenih alifatskih karbonilnih spojin. Primerna je za določevanje formaldehida in drugih karbonilnih spojin v približnem območju koncentracije od 1 μg/m3 do 1 mg/m3. Metoda vzorčenja podaja časovno tehtani povprečni (TWA) vzorec. Uporablja se lahko za dolgoročno (od 1 do 24 h) ali kratkoročno (od 5 do 60 min) vzorčenje zraka za formaldehid. Ta del standarda ISO 16000 določa postopek za vzorčenje in analizo formaldehida in drugih karbonilnih spojin, ki vključuje zbiranje iz zraka v kasete za adsorpcijo, prevlečene z 2,4-dinitrofenilhidrazinom (DNPH), ter poznejšo analizo hidrazonov, nastalih s tekočinsko kromatografijo visoke ločljivosti (HPLC), z zaznavanjem prek ultravijolične absorpcije[12],[16]. Metoda ni ustrezna za daljše verižne ali nenasičene karbonilne spojine.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-april-2012
1DGRPHãþD
SIST ISO 16000-3:2002
1RWUDQML]UDNGHO'RORþHYDQMHIRUPDOGHKLGDLQGUXJLKNDUERQLOQLKVSRMLQY
QRWUDQMHP]UDNXLQ]UDNXYSUHVNXVQLKNRPRUDK0HWRGDDNWLYQHJDY]RUþHQMD
Indoor air - Part 3: Determination of formaldehyde and other carbonyl compounds in
indoor air and test chamber air - Active sampling method
Air intérieur - Partie 3: Dosage du formaldéhyde et d'autres composés carbonylés dans
l'air intérieur et dans l'air des chambres d'essai - Méthode par échantillonnage actif
Ta slovenski standard je istoveten z: ISO 16000-3:2011
ICS:
13.040.20 Kakovost okoljskega zraka Ambient atmospheres
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
INTERNATIONAL ISO
STANDARD 16000-3
Second edition
2011-10-15
Indoor air —
Part 3:
Determination of formaldehyde and other
carbonyl compounds in indoor air and
test chamber air — Active sampling
method
Air intérieur —
Partie 3: Dosage du formaldéhyde et d'autres composés carbonylés
dans l'air intérieur et dans l'air des chambres d'essai — Méthode par
échantillonnage actif
Reference number
©
ISO 2011
© ISO 2011
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2011 – All rights reserved
Contents Page
Foreword . iv
Introduction . vi
1 Scope . 1
2 Normative references . 2
3 Principle . 2
4 Limitations and interferences . 2
5 Safety measures . 3
6 Apparatus . 4
7 Reagents and materials . 7
8 Preparation of reagents and cartridges . 7
9 Procedure . 10
10 Calculations . 19
11 Performance criteria and quality assurance . 20
12 Precision and uncertainty . 22
13 Test report . 22
Annex A (informative) Precision and uncertainty . 23
Annex B (informative) Melting points of DNPH-carbonyl derivatives . 25
Bibliography . 26
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 16000-3 was prepared by Technical Committee ISO/TC 146, Air quality, Subcommittee SC 6, Indoor air.
This second edition cancels and replaces the first edition (ISO 16000-3:2001), which has been technically
revised.
ISO 16000 consists of the following parts, under the general title Indoor air:
Part 1: General aspects of sampling strategy
Part 2: Sampling strategy for formaldehyde
Part 3: Determination of formaldehyde and other carbonyl compounds in indoor air and test chamber
air — Active sampling method
Part 4: Determination of formaldehyde — Diffusive sampling method
Part 5: Sampling strategy for volatile organic compounds (VOCs)
Part 6: Determination of volatile organic compounds in indoor and test chamber air by active sampling on ®
Tenax TA sorbent, thermal desorption and gas chromatography using MS or MS-FID
Part 7: Sampling strategy for determination of airborne asbestos fibre concentrations
Part 8: Determination of local mean ages of air in buildings for characterizing ventilation conditions
Part 9: Determination of the emission of volatile organic compounds from building products and
furnishing — Emission test chamber method
Part 10: Determination of the emission of volatile organic compounds from building products and
furnishing — Emission test cell method
Part 11: Determination of the emission of volatile organic compounds from building products and
furnishing — Sampling, storage of samples and preparation of test specimens
Part 12: Sampling strategy for polychlorinated biphenyls (PCBs), polychlorinated dibenzo-p-dioxins
(PCDDs), polychlorinated dibenzofurans (PCDFs) and polycyclic aromatic hydrocarbons (PAHs)
iv © ISO 2011 – All rights reserved
Part 13: Determination of total (gas and particle-phase) polychlorinated dioxin-like biphenyls (PCBs) and
polychlorinated dibenzo-p-dioxins/dibenzofurans (PCDDs/PCDFs) — Collection on sorbent-backed filters
Part 14: Determination of total (gas and particle-phase) polychlorinated dioxin-like biphenyls (PCBs) and
polychlorinated dibenzo-p-dioxins/dibenzofurans (PCDDs/PCDFs) — Extraction, clean-up and analysis by
high-resolution gas chromatography and mass spectrometry
Part 15: Sampling strategy for nitrogen dioxide (NO )
Part 16: Detection and enumeration of moulds — Sampling by filtration
Part 17: Detection and enumeration of moulds — Culture-based method
Part 18: Detection and enumeration of moulds — Sampling by impaction
Part 19: Sampling strategy for moulds
Part 23: Performance test for evaluating the reduction of formaldehyde concentrations by sorptive
building materials
Part 24: Performance test for evaluating the reduction of volatile organic compound (except
formaldehyde) concentrations by sorptive building materials
Part 25: Determination of the emission of semi-volatile organic compounds by building products — Micro-
chamber method
Part 26: Sampling strategy for carbon dioxide (CO )
Part 28: Determination of odour emissions from building products using test chambers
The following parts are under preparation:
Part 21: Detection and enumeration of moulds — Sampling from materials
Part 27: Determination of settled fibrous dust on surfaces by SEM (scanning electron microscopy) (direct
method)
Part 29: Test methods for VOC detectors
Part 30: Sensory testing of indoor air
Part 31: Measurement of flame retardants and plasticizers based on organophosphorus compounds —
Phosphoric acid ester
Part 32: Investigation of constructions on pollutants and other injurious factors — Inspections
Introduction
This part of ISO 16000 is intended to be used for characterizing indoor air following the sampling strategy
specified in ISO 16000-2. It is applicable to formaldehyde and other carbonyl compounds. It has been tested
for 14 aldehydes and ketones. Formaldehyde is the simplest carbonyl compound, with one carbon, one
oxygen and two hydrogen atoms. In its monomolecular state, it is a colourless, pungent, reactive gas. It has
been used in the production of urea-formaldehyde resins, adhesives, and insulating foams. Emissions from
particle (chip) board and wall insulation are the major sources of formaldehyde in indoor air.
Formaldehyde is collected by passing air through a reactive medium that converts the compound to a
derivative of lower vapour pressure that is more efficiently retained by the sampler and can be easily analysed.
This part of ISO 16000 determines formaldehyde and other carbonyl compounds by reaction with
2,4-dinitrophenylhydrazine coated on to a sorbent to convert them to their corresponding hydrazones, which
can be recovered and measured with high sensitivity, precision, and accuracy. Other carbonyl compounds
that may be emitted into air from solvents, adhesives, cosmetics, and other sources can also be determined
using this part of ISO 16000.
[12]
The sampling procedure is based on US EPA method TO-11A .
[15]
Formaldehyde and certain other carbonyl compounds have a high toxic potential .
[7][8] [2]–[6]
ISO 16017 and ISO 12219 also focus on volatile organic compound (VOC) measurements.
vi © ISO 2011 – All rights reserved
INTERNATIONAL STANDARD ISO 16000-3:2011(E)
Indoor air —
Part 3:
Determination of formaldehyde and other carbonyl compounds
in indoor air and test chamber air — Active sampling method
WARNING — Persons using this part of ISO 16000 should be familiar with normal laboratory practice.
This part of ISO 16000 does not purport to address all of the safety problems, if any, associated with
its use. It is the responsibility of the user to establish appropriate safety and health practices and to
ensure compliance with any national regulatory conditions.
1 Scope
This part of ISO 16000 specifies a determination of formaldehyde (HCHO) and other carbonyl compounds
1
(aldehydes and ketones) in air. The method is specific to formaldehyde but, with modification, at least
12 other aromatic as well as saturated and unsaturated aliphatic carbonyl compounds can be detected and
quantified. It is suitable for determination of formaldehyde and other carbonyl compounds in the approximate
3 3
concentration range 1 µg/m to 1 mg/m . The sampling method gives a time-weighted average (TWA) sample.
It can be used for long-term (1 h to 24 h) or short-term (5 min to 60 min) sampling of air for formaldehyde.
This part of ISO 16000 specifies a sampling and analysis procedure for formaldehyde and other carbonyl
compounds that involves collection from air on to adsorbent cartridges coated with 2,4-dinitrophenylhydrazine
(DNPH) and subsequent analysis of the hydrazones formed by high performance liquid chromatography
[12],[16]
(HPLC) with detection by ultraviolet absorption . The method is not suitable for longer chained or
unsaturated carbonyl compounds.
This part of ISO 16000 applies to the determination of:
acetaldehyde 2,5-dimethylbenzaldehyde m -tolualdehyde
acetone formaldehyde o -tolualdehyde
benzaldehyde isovaleraldehyde p -tolualdehyde
butyraldehyde propionaldehyde valeraldehyde
capronaldehyde
1 Instead of systematic IUPAC nomenclature, traditional names are used in this part of ISO 16000. Some equivalent
names are:
acetaldehyde: ethanal formaldehyde: methanal o -tolualdehyde: 2-methylbenzaldehyde
acetone: 2-propanone isovaleraldehyde: 3-methylbutanal p -tolualdehyde: 4-methylbenzaldehyde
butyraldehyde: butanal propionaldehyde: propanal valeraldehyde: pentanal
capronaldehyde: hexanal m -tolualdehyde: 3-methylbenzaldehyde
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO/IEC 17025, General requirements for the competence of testing and calibration laboratories
3 Principle
The method specified in this part of ISO 16000 involves drawing air through a cartridge containing silica g
...
INTERNATIONAL ISO
STANDARD 16000-3
Second edition
2011-10-15
Indoor air —
Part 3:
Determination of formaldehyde and other
carbonyl compounds in indoor air and
test chamber air — Active sampling
method
Air intérieur —
Partie 3: Dosage du formaldéhyde et d'autres composés carbonylés
dans l'air intérieur et dans l'air des chambres d'essai — Méthode par
échantillonnage actif
Reference number
©
ISO 2011
© ISO 2011
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2011 – All rights reserved
Contents Page
Foreword . iv
Introduction . vi
1 Scope . 1
2 Normative references . 2
3 Principle . 2
4 Limitations and interferences . 2
5 Safety measures . 3
6 Apparatus . 4
7 Reagents and materials . 7
8 Preparation of reagents and cartridges . 7
9 Procedure . 10
10 Calculations . 19
11 Performance criteria and quality assurance . 20
12 Precision and uncertainty . 22
13 Test report . 22
Annex A (informative) Precision and uncertainty . 23
Annex B (informative) Melting points of DNPH-carbonyl derivatives . 25
Bibliography . 26
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 16000-3 was prepared by Technical Committee ISO/TC 146, Air quality, Subcommittee SC 6, Indoor air.
This second edition cancels and replaces the first edition (ISO 16000-3:2001), which has been technically
revised.
ISO 16000 consists of the following parts, under the general title Indoor air:
Part 1: General aspects of sampling strategy
Part 2: Sampling strategy for formaldehyde
Part 3: Determination of formaldehyde and other carbonyl compounds in indoor air and test chamber
air — Active sampling method
Part 4: Determination of formaldehyde — Diffusive sampling method
Part 5: Sampling strategy for volatile organic compounds (VOCs)
Part 6: Determination of volatile organic compounds in indoor and test chamber air by active sampling on ®
Tenax TA sorbent, thermal desorption and gas chromatography using MS or MS-FID
Part 7: Sampling strategy for determination of airborne asbestos fibre concentrations
Part 8: Determination of local mean ages of air in buildings for characterizing ventilation conditions
Part 9: Determination of the emission of volatile organic compounds from building products and
furnishing — Emission test chamber method
Part 10: Determination of the emission of volatile organic compounds from building products and
furnishing — Emission test cell method
Part 11: Determination of the emission of volatile organic compounds from building products and
furnishing — Sampling, storage of samples and preparation of test specimens
Part 12: Sampling strategy for polychlorinated biphenyls (PCBs), polychlorinated dibenzo-p-dioxins
(PCDDs), polychlorinated dibenzofurans (PCDFs) and polycyclic aromatic hydrocarbons (PAHs)
iv © ISO 2011 – All rights reserved
Part 13: Determination of total (gas and particle-phase) polychlorinated dioxin-like biphenyls (PCBs) and
polychlorinated dibenzo-p-dioxins/dibenzofurans (PCDDs/PCDFs) — Collection on sorbent-backed filters
Part 14: Determination of total (gas and particle-phase) polychlorinated dioxin-like biphenyls (PCBs) and
polychlorinated dibenzo-p-dioxins/dibenzofurans (PCDDs/PCDFs) — Extraction, clean-up and analysis by
high-resolution gas chromatography and mass spectrometry
Part 15: Sampling strategy for nitrogen dioxide (NO )
Part 16: Detection and enumeration of moulds — Sampling by filtration
Part 17: Detection and enumeration of moulds — Culture-based method
Part 18: Detection and enumeration of moulds — Sampling by impaction
Part 19: Sampling strategy for moulds
Part 23: Performance test for evaluating the reduction of formaldehyde concentrations by sorptive
building materials
Part 24: Performance test for evaluating the reduction of volatile organic compound (except
formaldehyde) concentrations by sorptive building materials
Part 25: Determination of the emission of semi-volatile organic compounds by building products — Micro-
chamber method
Part 26: Sampling strategy for carbon dioxide (CO )
Part 28: Determination of odour emissions from building products using test chambers
The following parts are under preparation:
Part 21: Detection and enumeration of moulds — Sampling from materials
Part 27: Determination of settled fibrous dust on surfaces by SEM (scanning electron microscopy) (direct
method)
Part 29: Test methods for VOC detectors
Part 30: Sensory testing of indoor air
Part 31: Measurement of flame retardants and plasticizers based on organophosphorus compounds —
Phosphoric acid ester
Part 32: Investigation of constructions on pollutants and other injurious factors — Inspections
Introduction
This part of ISO 16000 is intended to be used for characterizing indoor air following the sampling strategy
specified in ISO 16000-2. It is applicable to formaldehyde and other carbonyl compounds. It has been tested
for 14 aldehydes and ketones. Formaldehyde is the simplest carbonyl compound, with one carbon, one
oxygen and two hydrogen atoms. In its monomolecular state, it is a colourless, pungent, reactive gas. It has
been used in the production of urea-formaldehyde resins, adhesives, and insulating foams. Emissions from
particle (chip) board and wall insulation are the major sources of formaldehyde in indoor air.
Formaldehyde is collected by passing air through a reactive medium that converts the compound to a
derivative of lower vapour pressure that is more efficiently retained by the sampler and can be easily analysed.
This part of ISO 16000 determines formaldehyde and other carbonyl compounds by reaction with
2,4-dinitrophenylhydrazine coated on to a sorbent to convert them to their corresponding hydrazones, which
can be recovered and measured with high sensitivity, precision, and accuracy. Other carbonyl compounds
that may be emitted into air from solvents, adhesives, cosmetics, and other sources can also be determined
using this part of ISO 16000.
[12]
The sampling procedure is based on US EPA method TO-11A .
[15]
Formaldehyde and certain other carbonyl compounds have a high toxic potential .
[7][8] [2]–[6]
ISO 16017 and ISO 12219 also focus on volatile organic compound (VOC) measurements.
vi © ISO 2011 – All rights reserved
INTERNATIONAL STANDARD ISO 16000-3:2011(E)
Indoor air —
Part 3:
Determination of formaldehyde and other carbonyl compounds
in indoor air and test chamber air — Active sampling method
WARNING — Persons using this part of ISO 16000 should be familiar with normal laboratory practice.
This part of ISO 16000 does not purport to address all of the safety problems, if any, associated with
its use. It is the responsibility of the user to establish appropriate safety and health practices and to
ensure compliance with any national regulatory conditions.
1 Scope
This part of ISO 16000 specifies a determination of formaldehyde (HCHO) and other carbonyl compounds
1
(aldehydes and ketones) in air. The method is specific to formaldehyde but, with modification, at least
12 other aromatic as well as saturated and unsaturated aliphatic carbonyl compounds can be detected and
quantified. It is suitable for determination of formaldehyde and other carbonyl compounds in the approximate
3 3
concentration range 1 µg/m to 1 mg/m . The sampling method gives a time-weighted average (TWA) sample.
It can be used for long-term (1 h to 24 h) or short-term (5 min to 60 min) sampling of air for formaldehyde.
This part of ISO 16000 specifies a sampling and analysis procedure for formaldehyde and other carbonyl
compounds that involves collection from air on to adsorbent cartridges coated with 2,4-dinitrophenylhydrazine
(DNPH) and subsequent analysis of the hydrazones formed by high performance liquid chromatography
[12],[16]
(HPLC) with detection by ultraviolet absorption . The method is not suitable for longer chained or
unsaturated carbonyl compounds.
This part of ISO 16000 applies to the determination of:
acetaldehyde 2,5-dimethylbenzaldehyde m -tolualdehyde
acetone formaldehyde o -tolualdehyde
benzaldehyde isovaleraldehyde p -tolualdehyde
butyraldehyde propionaldehyde valeraldehyde
capronaldehyde
1 Instead of systematic IUPAC nomenclature, traditional names are used in this part of ISO 16000. Some equivalent
names are:
acetaldehyde: ethanal formaldehyde: methanal o -tolualdehyde: 2-methylbenzaldehyde
acetone: 2-propanone isovaleraldehyde: 3-methylbutanal p -tolualdehyde: 4-methylbenzaldehyde
butyraldehyde: butanal propionaldehyde: propanal valeraldehyde: pentanal
capronaldehyde: hexanal m -tolualdehyde: 3-methylbenzaldehyde
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO/IEC 17025, General requirements for the competence of testing and calibration laboratories
3 Principle
The method specified in this part of ISO 16000 involves drawing air through a cartridge containing silica gel
coated with 2,4-dinitrophenylhydrazine (DNPH) reagent. The principle of the method is based on the specific
reaction of a carbonyl group with DNPH in the presence of an acid to form stable derivatives according to the
reaction shown in Figure 1. The DNPH derivatives are analysed for the parent aldehydes and ketones utilizing
high performance liquid chromatography (HPLC) with UV detection or diode array detection. The detection
has been extended to other carbonyl compounds that can be determined as outlined in 9.3.5.
This part of ISO 16000 instructs the user on how to prepare sampling cartridges from commercially available
chromatographic grade silica gel cartridges by the application of acidified DNPH to each cartridge.
Alternatively, pre-coated DNPH silica gel cartridges are available and are recommended since they are
generally more uniform in manufacture and possess lower blank levels. However, if commercial cartridges are
used, they shall be demonstrated to meet the performance criteria of this part of ISO 16000. Another
advantage of commercial cartridges is that they are available with larger particle size s
...
NORME ISO
INTERNATIONALE 16000-3
Deuxième édition
2011-10-15
Air intérieur —
Partie 3:
Dosage du formaldéhyde et d'autres
composés carbonylés dans l'air intérieur
et dans l'air des chambres d'essai —
Méthode par échantillonnage actif
Indoor air —
Part 3: Determination of formaldehyde and other carbonyl compounds
in indoor air and test chamber air — Active sampling method
Numéro de référence
©
ISO 2011
DOCUMENT PROTÉGÉ PAR COPYRIGHT
© ISO 2011
Droits de reproduction réservés. Sauf prescription différente, aucune partie de cette publication ne peut être reproduite ni utilisée sous
quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie et les microfilms, sans l'accord écrit
de l'ISO à l'adresse ci-après ou du comité membre de l'ISO dans le pays du demandeur.
ISO copyright office
Case postale 56 CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Publié en Suisse
ii © ISO 2011 – Tous droits réservés
Sommaire Page
Avant-propos . iv
Introduction . vi
1 Domaine d'application . 1
2 Références normatives . 2
3 Principe . 2
4 Limites et interférences . 2
5 Mesures de sécurité . 3
6 Appareillage . 4
7 Réactifs et matériaux . 7
8 Préparation des réactifs et des cartouches . 7
9 Mode opératoire . 10
10 Calculs . 20
11 Critères de performance et assurance qualité . 21
12 Fidélité et incertitude . 23
13 Rapport d'essai . 23
Annexe A (informative) Fidélité et incertitude. 24
Annexe B (informative) Points de fusion des dérivés DNPH-carbonylés . 26
Bibliographie . 27
Avant-propos
L'ISO (Organisation internationale de normalisation) est une fédération mondiale d'organismes nationaux de
normalisation (comités membres de l'ISO). L'élaboration des Normes internationales est en général confiée
aux comités techniques de l'ISO. Chaque comité membre intéressé par une étude a le droit de faire partie du
comité technique créé à cet effet. Les organisations internationales, gouvernementales et non
gouvernementales, en liaison avec l'ISO participent également aux travaux. L'ISO collabore étroitement avec
la Commission électrotechnique internationale (CEI) en ce qui concerne la normalisation électrotechnique.
Les Normes internationales sont rédigées conformément aux règles données dans les Directives ISO/CEI,
Partie 2.
La tâche principale des comités techniques est d'élaborer les Normes internationales. Les projets de Normes
internationales adoptés par les comités techniques sont soumis aux comités membres pour vote. Leur
publication comme Normes internationales requiert l'approbation de 75 % au moins des comités membres
votants.
L'attention est appelée sur le fait que certains des éléments du présent document peuvent faire l'objet de
droits de propriété intellectuelle ou de droits analogues. L'ISO ne saurait être tenue pour responsable de ne
pas avoir identifié de tels droits de propriété et averti de leur existence.
L'ISO 16000-3 a été élaborée par le comité technique ISO/TC 146, Qualité de l'air, sous-comité SC 6, Air
intérieur.
Cette deuxième édition annule et remplace la première édition (ISO 16000-3:2001), qui a fait l'objet d'une
révision technique.
L'ISO 16000 comprend les parties suivantes, présentées sous le titre général Air intérieur:
Partie 1: Aspects généraux de la stratégie d'échantillonnage
Partie 2: Stratégie d'échantillonnage du formaldéhyde
Partie 3: Dosage du formaldéhyde et d'autres composés carbonylés dans l'air intérieur et dans l'air des
chambres d'essai — Méthode par échantillonnage actif
Partie 4: Dosage du formaldéhyde — Méthode par échantillonnage diffusif
Partie 5: Stratégie d'échantillonnage pour les composés organiques volatils (COV)
Partie 6: Dosage des composés organiques volatils dans l'air intérieur des locaux et chambres d'essai ®
par échantillonnage actif sur le sorbant Tenax TA , désorption thermique et chromatographie en phase
gazeuse utilisant MS ou MS-FID
Partie 7: Stratégie d'échantillonnage pour la détermination des concentrations en fibres d'amiante en
suspension dans l'air
Partie 8: Détermination des âges moyens locaux de l'air dans des bâtiments pour caractériser les
conditions de ventilation
Partie 9: Dosage de l'émission de composés organiques volatils de produits de construction et d'objets
d'équipement — Méthode de la chambre d'essai d'émission
Partie 10: Dosage de l'émission de composés organiques volatils de produits de construction et d'objets
d'équipement — Méthode de la cellule d'essai d'émission
iv © ISO 2011 – Tous droits réservés
Partie 11: Dosage de l'émission de composés organiques volatils de produits de construction et d'objets
d'équipement — Échantillonnage, conservation des échantillons et préparation d'échantillons pour essai
Partie 12: Stratégie d'échantillonnage des polychlorobiphényles (PCB), des polychlorodibenzo-p-dioxines
(PCDD), des polychlorodibenzofuranes (PCDF) et des hydrocarbures aromatiques polycycliques (HAP)
Partie 13: Dosage des polychlorobiphényles (PCB) de type dioxine et des polychlorodibenzo-p-dioxines
(PCDD)/polychlorodibenzofuranes (PCDF) totaux (en phase gazeuse et en phase particulaire) —
Collecte sur des filtres adsorbants
Partie 14: Dosage des polychlorobiphényles (PCB) de type dioxine et des polychlorodibenzo-p-dioxines
(PCDD)/polychlorodibenzofuranes (PCDF) totaux (en phase gazeuse et en phase particulaire) —
Extraction, purification et analyse par chromatographie en phase gazeuse haute résolution et
spectrométrie de masse
Partie 15: Stratégie d'échantillonnage du dioxyde d'azote (NO )
Partie 16: Détection et dénombrement des moisissures — Échantillonnage par filtration
Partie 17: Détection et dénombrement des moisissures — Méthode par culture
Partie 18: Détection et dénombrement des moisissures — Échantillonnage par impaction
Partie 19: Stratégie d'échantillonnage des moisissures
Partie 23: Essai de performance pour l'évaluation de la réduction des concentrations en formaldéhyde
par des matériaux de construction sorptifs
Partie 24: Essai de performance pour l'évaluation de la réduction des concentrations en composés
organiques volatils (sauf formaldéhyde) par des matériaux de construction sorptifs
Partie 25: Dosage de l'émission de composés organiques semi-volatils des produits de construction —
Méthode de la micro-chambre
Partie 26: Stratégie d'échantillonnage du dioxyde de carbone (CO )
Partie 28: Détermination des émissions d'odeurs des produits de construction au moyen de chambres
d'essai
Les parties suivantes sont en cours d'élaboration:
Partie 21: Détection et dénombrement des moisissures — Échantillonnage à partir de matériaux
Partie 27: Détermination de la poussière fibreuse déposée sur les surfaces par microscopie électronique
à balayage (MEB) (méthode directe)
Partie 29: Méthodes d'essai pour détecteurs de composés organiques volatils (COV)
Partie 30: Essai sensoriel de l'air intérieur
Partie 31: Mesurage des ignifugeants basés sur des composés organophosphorés — Ester d'acide
phosphorique
Partie 32: Investigation de polluants et autres facteurs nocifs dans les constructions — Inspections
Introduction
La présente partie de l'ISO 16000 est destinée à être utilisée pour caractériser l'air intérieur selon la stratégie
d'échantillonnage spécifiée dans l'ISO 16000-2. Elle est applicable au formaldéhyde et à d'autres composés
carbonylés. Elle a été soumise à essai pour 14 aldéhydes et cétones. Le formaldéhyde est le composé
carbonylé le plus simple, avec un atome de carbone, un atome d'oxygène et deux atomes d'hydrogène. Sous
sa forme mono-moléculaire, c'est un gaz réactif incolore et âcre. Il a été utilisé dans la production de résines,
d'adhésifs et de mousses isolantes d'urée formaldéhyde. Les émissions des panneaux de particules
(copeaux) et des isolations murales sont les principales sources de formaldéhyde dans l'air intérieur.
Le formaldéhyde est collecté en faisant passer de l'air à travers un milieu réactif qui convertit le composé en
un dérivé de pression de vapeur inférieure qui est plus efficacement retenu par l'échantillonneur et peut être
aisément analysé. La présente partie de l'ISO 16000 permet de doser le formaldéhyde et d'autres composés
carbonylés par réaction avec de la 2,4-dinitrophénylhydrazine imprégnée sur un sorbant pour les convertir en
leurs hydrazones correspondantes, qui peuvent être récupérées et mesurées avec une haute sensibilité,
précision et justesse. Les autres composés carbonylés qui peuvent être émis dans l'air par les solvants, les
adhésifs, les produits cosmétiques et d'autres sources peuvent également être dosés en utilisant la présente
partie de l'ISO 16000.
[12]
Le mode opératoire d'échantillonnage repose sur la méthode TO-11A de l'Agence américaine de protection
de l'environnement (EPA).
[15]
Le formaldéhyde et certains autres composés carbonylés ont un fort potentiel toxique .
[7][8] [2]-[6]
L'ISO 16017 et l'ISO 12219 portent plus particulièrement sur les mesurages relatifs aux composés
organiques volatils (COV).
vi © ISO 2011 – Tous droits réservés
NORME INTERNATIONALE ISO 16000-3:2011(F)
Air intérieur —
Partie 3:
Dosage du formaldéhyde et d'autres composés carbonylés
dans l'air intérieur et dans l'air des chambres d'essai —
Méthode par échantillonnage actif
AVERTISSEMENT — Il convient que l'utilisateur de la présente partie de l'ISO 16000 connaisse bien
les pratiques courantes de laboratoire. La présente partie de l'ISO 16000 n'a pas pour but de traiter
tous les problèmes de sécurité qui sont, le cas échéant, liés à son utilisation. Il incombe à l'utilisateur
d'établir des pratiques appropriées en matière d'hygiène et de sécurité, et de s'assurer de la
conformité à la réglementation nationale en vigueur.
1 Domaine d'application
La présente partie de l'ISO 16000 spécifie un dosage du formaldéhyde (HCHO) et d'autres composés
1)
carbonylés (aldéhydes et cétones) dans l'air. La méthode est spécifique au formaldéhyde. Toutefois, si elle
est modifiée, au moins 12 autres composés carbonylés peuvent être détectés et quantifiés. Elle convient au
dosage du formaldéhyde et d'autres composés carbonylés dans la plage de concentration comprise entre
3 3
environ 1 µg/m et 1 mg/m . La méthode d'échantillonnage fournit un résultat moyen pondéré dans le temps
(TWA). Elle peut être utilisée pour l'échantillonnage du formaldéhyde dans l'air à long terme (1 h à 24 h) ou à
court terme (5 min à 60 min).
La présente partie de l'ISO 16000 spécifie un mode opératoire d'échantillonnage et d'analyse pour le
formaldéhyde et d'autres composés carbonylés qui implique un prélèvement de l'air sur des cartouches
imprégnées de 2,4-dinitrophénylhydrazine (DNPH) et une analyse ultérieure par chromatographie en phase
[12][16]
liquide à haute performance (CLHP) avec détection par absorption ultraviolette . La méthode n'est pas
adaptée pour les composés carbonylés à plus longues chaînes ou insaturés.
La présente partie de l'ISO 16000 est applicable au dosage des composés suivants:
acétaldéhyde 2,5-diméthylbenzaldéhyde m -tolualdéhyde
acétone formaldéhyde o -tolualdéhyde
benzaldéhyde isovaléraldéhyde p -tolualdéhyde
butyraldéhyde propionaldéhyde valéraldéhyde
capronaldéhyde
1) Dans la présente partie de l'ISO 16000, les noms traditionnels sont utilisés à la place de la nomenclature
systématique de l'IUPAC. Quelques noms équivalents sont:
acétaldéhyde: éthanal formaldéhyde: méthanal o -tolualdéhyde: 2-méthylbenzaldéhyde
acétone: 2-propanone isovaléraldéhyde: 3-méthylbutanal p -tolualdéhyde: 4-méthylbenzaldéhyde
butyraldéhyde: butanal propionaldéhyde: propanal valéraldéhyde: pentanal
capronaldéhyde: hexanal m -tolualdéhyde: 3-méthylbenzaldéhyde
2 Références normatives
Les documents de référence suivants sont indispensables pour l'application du présent document. Pour les
références datées, seule l'édition citée s'applique. Pour l
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.