SIST EN 300 392-1 V1.4.1:2009

• Abstract:

  The present document defines addressing for Terrestrial Trunked Radio system (TETRA) supporting Voice plus Data (V+D). It also gives background information of the air interface, the interworking between TETRA systems and to other systems via gateways, the terminal equipment interface on the Mobile Station (MS), the security aspects in TETRA networks, the management services offered to the operator, the performance objectives, and the supplementary services that come in addition to the basic and tele-services used as a basis for TETRA standardization. The present document defines and specifies the TETRA addressing and identities and their organization in groups corresponding to the different functions. It establishes the background of the TETRA general network design for standardization purposes:; - it gives information about the circuit mode and packet mode reference points for the MS and switching and management infrastructure;; - it gives information about a model of the air interface protocol stack, different functions of layers and sublayers;; - it gives information about the functions provided by the circuit mode teleservices used for speech and basic services used for data transfer;; - it gives information about the functions related to the management of the users' mobility across networks and inside a network including roaming and migration;; - it gives information about the functions related to the transport of short data messages as a service specific to TETRA;; - it gives information about the functions related to the support of packet data service in a way specific to TETRA;; - it gives information about the supplementary services that mainly extend the capabilities of the circuit mode basic and teleservices;; - it gives information about the various possibilities of individual circuit mode call scenarios and provides guidance on priority concepts for packet data and circuit mode services and on the service quality. NOTE: This part of the multi-part document may, by its nature as a general design statement, require updating when later parts of the multi-part document are completed and maintained (in order to avoid any non-alignment). If a discrepancy occurs between this part and any other part of the multi-part document, then the other part will take precedence. The present document may be maintained mainly on those clauses, which are referred from other parts or standards.

• Status: Published
• Publication Date: 02-Mar-2009
• ICS: 33.070.10 - Terrestrial Trunked Radio (TETRA)
• Technical Committee: MOC - Mobile Communications
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 17-Feb-2009
• Due Date: 24-Apr-2009
• Completion Date: 03-Mar-2009
• Mandate: BC-T-344
• Ref Project: ETSI EN 300 392-1 V1.4.1 (2009-01) - Terrestrial Trunked Radio (TETRA); Voice plus Data (V+D); Part 1: General network design

SIST EN 300 392-1 V1.4.1:2009 is the Slovenian adoption of ETSI EN 300 392-1 V1.4.1 for Terrestrial Trunked Radio (TETRA) - Voice plus Data (V+D). It defines the general network design background for TETRA V+D, with emphasis on addressing, identities, reference points, protocol architecture, mobility, short data, call scenarios, and supplementary services. The document is aimed at people who design, integrate, operate, or test TETRA networks and terminals.

What does SIST EN 300 392-1 V1.4.1:2009 specify?

SIST EN 300 392-1 V1.4.1:2009 specifies the TETRA V+D network design framework that other TETRA parts build on. It sets out how TETRA identities and addresses are organized, and it gives the background model for air interface behavior, interworking, mobility, SDS, packet data, circuit mode services, and supplementary services.

The document is organized into clauses on scope, references, definitions, circuit mode and packet mode reference points, protocol architecture, addressing and identities, services, mobility management, SDS, and supplementary services. Its annexes expand those topics with reference configurations, protocol models, call scenarios, priority concepts, mobility procedures, packet-mode reference points, QoS, and supplementary-service background.

Annex	What it covers
A	Circuit mode reference points and LMN access
B	Protocol architecture for V+D
C	Overview of circuit mode basic services
D	Individual circuit mode call scenarios
E	Group voice call scenarios
F	Priority functions for circuit mode services
G	Mobility Management (MM) in MS
H	MLE mobility scenarios and functionalities
J	Technical realization of SDS
K	General supplementary services background
L	Packet mode reference points
M	Quality of Service (QoS)

What are the key requirements of SIST EN 300 392-1 V1.4.1:2009?

SIST EN 300 392-1 V1.4.1:2009 is mainly a design and framework standard, so the most important points are the interfaces, identities, service models, and control concepts that later parts depend on.

• Clause 4 and clause 5 define circuit mode and packet mode reference points for the Mobile Station (MS) and the switching and management infrastructure. In practice, these reference points help engineers place functions at the right interface and decide what belongs in the terminal, the network, or a gateway.

• Clause 6 gives the V+D protocol architecture. It separates the physical layer, Medium Access Control (MAC), Logical Link Control (LLC), Mobile/Base Link control Entity (MLE/BLE), and upper-layer functions, so implementers can map signaling, user data, and management tasks to the correct layer.

• Clause 7 defines the addressing and identity framework. It covers subscriber identities, TETRA Management Identity (TMI), Network SAP (NSAP) addresses, TETRA Equipment Identity (TEI), Mobile Network Identity (MNI), layer 2 labels, and address use for internal, inter-TETRA, and external calls. This matters because correct identity allocation and routing are central to call setup, roaming, and interworking.

• Clause 7.9 covers addressing in interworking and roaming with other telecommunication networks. It links TETRA users to E.164 numbering and gateway dialing arrangements, which is what makes outside-network reachability and two-stage dialing work in practice.

• Clause 8 and Annex C to Annex E describe circuit mode basic services and call behavior. They cover call control, user data transport, message trunking, transmission trunking, quasi-transmission trunking, request-to-transmit, and call clearing, which are the service behaviors operators and equipment vendors need to align on.

• Clause 9 and Annex G cover Mobility Management (MM) in the MS. They include registration, authentication, de-registration, periodic registration, disable/enable, energy economy mode change, and group identity download, which are the procedures that keep a moving user attached and recognized.

• Annex F and Annex M provide the background for priority and service quality. Annex F covers access priority, call type priority, queue priority, pre-emptive priority, call retention priority, and subscriber priority, while Annex M discusses QoS parameters such as delay, throughput, residual error rate, transfer failure probability, and resilience.

What terms does SIST EN 300 392-1 V1.4.1:2009 define?

• Mobile Station (MS) - The physical grouping that contains the mobile equipment used to obtain TETRA services.

• Short Subscriber Identity (SSI) - The network-specific part of a TETRA subscriber identity, valid only within one TETRA sub-domain.

• TETRA Management Identity (TMI) - A network address used by the operator to address a particular Mobile Termination or Line Termination.

• TETRA Equipment Identity (TEI) - The permanent electronic serial number embedded in TETRA equipment.

• Mobile Network Identity (MNI) - The identity that uniquely identifies a TETRA network and is broadcast by its base stations.

• roaming - The act of changing Location Area within a network that uses the same MNC/MCC, with a valid registration.

• migration - The act of changing to a Location Area in another network, where the user does not have subscription for that network.

Who uses SIST EN 300 392-1 V1.4.1:2009?

SIST EN 300 392-1 V1.4.1:2009 is used by TETRA network architects, radio and protocol engineers, terminal and base-station designers, gateway and interworking vendors, and operators planning numbering, mobility, and service behavior. It is also useful for quality managers and test teams who need to check whether a design follows the TETRA V+D model for addressing, call control, SDS, supplementary services, and QoS.

Which standards are used with SIST EN 300 392-1 V1.4.1:2009?

• ITU-T E.164 - Provides the international public telecommunication numbering plan used for E.164 addressing.
• ITU-T E.218 - Covers allocation of terrestrial trunk radio Mobile Country Codes.
• ITU-T E.213 - Gives the numbering plan for land mobile stations in public land mobile networks.
• ETSI EN 300 392-2 - The TETRA V+D Air Interface reference for physical, MAC, and layer behavior.
• ETSI EN 300 392-7 - The TETRA V+D Security part.
• ETSI EN 300 392-10-22 - The supplementary service part for Dynamic Group Number Assignment (DGNA).
• ETSI EN 300 392-3-1 - The general design part for Inter-System Interface (ISI) interworking.
• ETSI TS 101 747 - The IP Interworking (IPI) reference for packet data services.
• ETSI EN 300 392-5 - The Peripheral Equipment Interface (PEI) reference used for external terminal connection.
• ETSI EN 300 392-10 - The wider supplementary services series used by the background material in this part.

What does the SIST EN 300 392-1 V1.4.1:2009 document contain?

The document contains reference configurations, protocol stack models, call-control scenarios, mobility procedures, and QoS background rather than a single set of product requirements. Annex A and Annex L show the reference points and access arrangements for MS, TETRA networks, and external connections. Annex B maps the V+D protocol stack across layer 1, layer 2, and layer 3 entities, and Annex C to Annex E show how circuit mode and group voice calls are set up and cleared. Annex G, Annex J, and Annex K support Mobility Management, SDS, and supplementary services standardization, while Annex M provides the QoS parameter framework and the related measurement concepts.

Final draft ETSI EN 300 392-1 V1.4.0 (2008-07)
European Standard (Telecommunications series)

Terrestrial Trunked Radio (TETRA);
Voice plus Data (V+D);
Part 1: General network design

2 Final draft ETSI EN 300 392-1 V1.4.0 (2008-07)

Reference
REN/TETRA-03190
Keywords
air interface, TETRA, V+D
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: [phone]  Fax: [phone]

Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88

Important notice
Individual copies of the present document can be downloaded from:
http://www.etsi.org
The present document may be made available in more than one electronic version or in print. In any case of existing or
perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF).
In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive
within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
http://portal.etsi.org/chaircor/ETSI_support.asp
Copyright Notification
No part may be reproduced except as authorized by written permission.
The copyright and the foregoing restriction extend to reproduction in all media.

© European Telecommunications Standards Institute 2008.
All rights reserved.
TM TM TM TM
DECT , PLUGTESTS , UMTS , TIPHON , the TIPHON logo and the ETSI logo are Trade Marks of ETSI registered
for the benefit of its Members.
TM
3GPP is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners.
ETSI
3 Final draft ETSI EN 300 392-1 V1.4.0 (2008-07)
Contents
Intellectual Property Rights.12
Foreword.12
1 Scope.14
2 References.14
2.1 Normative references.15
2.2 Informative references.15
3 Definitions, symbols and abbreviations .16
3.1 Definitions.16
3.2 Symbols.21
3.3 Abbreviations.22
4 Circuit mode reference points .24
5 Packet mode reference points.24
6 Protocol architecture for V+D.24
7 Addressing and identities .24
7.1 Introduction.24
7.2 Subscriber identities .26
7.2.1 General.26
7.2.2 TSI.27
7.2.3 SSI.28
7.2.4 Composition of subscriber identities .28
7.2.5 Allocation principles for subscriber identities .29
7.2.6 Use of subscriber identities.29
7.2.7 NSAP addresses.30
7.2.8 Installation of TSIs.30
7.3 TETRA Management Identity (TMI).30
7.3.1 General.30
7.3.2 Composition of management identities.31
7.3.3 Use of management identities.31
7.4 Network layer SAP (NSAP) addresses.31
7.4.1 General.31
7.4.2 Static binding.31
7.4.3 Dynamic binding.32
7.4.3.1 General.32
7.4.3.2 Structure and contents of NSAP addresses .32
7.4.3.3 Use of NSAP addresses.32
7.4.3.4 Binding of NSAP addresses .32
7.5 TETRA Equipment Identity (TEI) .32
7.5.1 General.32
7.5.2 Contents of TEI.33
7.5.3 Allocation principles for TEI.33
7.5.4 Use of TEI.33
7.6 Mobile Network Identity (MNI).34
7.6.1 Contents of MNI .34
7.7 Layer 2 addresses and labels .34
7.7.1 Overview.34
7.7.2 Event labelling.34
7.7.3 Scrambling labelling.34
7.7.4 Use and implementation of layer 2 addresses.35
7.7.4.1 General requirement.35
7.7.4.2 Implementation of event labels .35
7.7.4.3 Implementation of scrambling labels .35
7.7.5 Use of identities for V+D control channels .35
ETSI
4 Final draft ETSI EN 300 392-1 V1.4.0 (2008-07)
7.7.6 Labelling of packet channels .36
7.7.6.1 Use of identities for uplink data transfers .36
7.7.6.2 Use of identities for downlink data transfers.36
7.7.7 System information broadcast.37
7.7.8 Reserved value of group address for user information broadcast .37
7.8 Use of individual addresses.37
7.8.1 Air interface addressing functions .37
7.8.2 Address placement in primitives and PDUs .37
7.8.2.1 Use of ISSI at layer 2 .37
7.8.2.2 Use of ITSI/ISSI at layer 3.39
7.8.2.2.1 Void.39
7.8.2.2.2 Use of ITSI/ISSI by CMCE.39
7.8.3 Routing principles.40
7.8.3.1 Routing of intra-TETRA calls (within one TETRA network) .40
7.8.3.2 Routing of inter-TETRA calls (between two TETRA networks).40
7.8.3.3 Routing of external calls (to/from non-TETRA networks) .41
7.8.4 Address and identity comparison.41
7.9 Addressing in interworking and roaming with other telecommunication networks .41
8 Circuit mode basic services.41
9 Mobility Management (MM) in MS .42
10 MLE mobility scenarios and functionalities.42
11 Technical realization of SDS.42
12 Void.42
13 Void.42
14 General on supplementary services.42
Annex A (informative): Circuit mode reference points.43
A.1 Introduction.43
A.2 Reference configuration.43
A.2.1 Configuration examples of TETRA LMNs .44
A.3 TETRA LMN access.45
A.3.1 MS access.45
A.3.1.1 MS functional groups.45
A.3.1.2 MS access points and reference points .45
A.3.2 Void.46
A.3.3 Inter System Interface (ISI) access.46
A.3.4 Location of TETRA functionality .46
A.3.5 TETRA terminals.46
Annex B (informative): Protocol architecture for V+D .47
B.1 Introduction.47
B.2 Mobile/base protocol architecture .47
B.2.1 Overview.47
B.2.2 Air interface layer 1.47
B.2.3 Air interface layer 2.48
B.2.3.1 Medium Access Control (MAC).48
B.2.3.2 Logical Link Control (LLC) .50
B.2.4 Air interface layer 3.50
B.2.4.1 Mobile/Base Link control Entity (MLE/BLE).50
B.2.4.2 Sub-Network Access Functions (SNAF) .51
B.2.4.2.1 Mobility Management (MM) .51
B.2.4.2.2 Circuit Mode Control Entity (CMCE).51
B.2.4.2.3 Packet data handling .52
B.2.4.2.4 TETRA packet data protocol (PDP).52
ETSI
5 Final draft ETSI EN 300 392-1 V1.4.0 (2008-07)
B.2.4.2.5 Void.52
B.2.5 Mobile/base protocol stack.52
B.3 Lower Layer Management Entity (LLME) and other layers interaction.53
B.3.1 General description.53
Annex C (informative): Overview of circuit mode basic services .54
C.1 Introduction.54
C.2 Functional groupings in circuit switched mode calls .54
C.2.1 Circuit switched call control, C-plane .54
C.2.2 Circuit switched call, user data, U-plane.54
C.3 Protocols.54
C.3.1 TNP1.54
C.3.2 Void.54
C.3.3 TNP3.54
C.3.4 TNP4.55
C.3.5 AI1.55
C.3.6 AI2.55
C.3.7 TLC1.55
C.3.8 V.24T.55
C.4 Example configuration .55
C.4.1 MS to MS .55
C.4.2 Void.56
C.4.3 Void.56
C.4.4 MS to MS over ISI .56
Annex D (informative): Individual circuit mode call scenarios.58
D.1 Introduction.58
D.2 Procedures - message trunked systems .58
D.2.1 Call set-up - on/off hook signalling.58
D.2.1.1 Call set-up - on/off hook signalling flow.58
D.2.1.2 Traffic channel assignment.59
D.2.2 Call set-up - direct set-up signalling.59
D.2.2.1 Call set-up - direct set-up signalling flow.59
D.2.2.2 Traffic channel assignment.60
D.2.3 Request-to-transmit.61
D.2.4 Response to request-to-transmit .62
D.2.5 Permission to transmit withdrawn .62
D.2.6 Permission to continue with withdrawn call.62
D.2.7 End of transmission.62
D.2.8 Stop-transmission order.62
D.2.9 Call clearing.63
D.2.9.1 Mobile originated.63
D.2.9.2 SwMI originated.64
D.3 Procedures - transmission trunked systems.64
D.3.1 Call set-up - on/off hook signalling.64
D.3.1.1 Call set-up - on/off hook signalling flow.64
D.3.1.2 Traffic assignment.65
D.3.2 Call set-up - direct set-up signalling.65
D.3.2.1 Call set-up - direct set-up signalling flow.65
D.3.2.2 Traffic channel assignment.66
D.3.3 Request-to-transmit.66
D.3.4 Response to request-to-transmit .67
D.3.5 Permission to transmit withdrawn .68
D.3.6 Permission to continue with withdrawn call.68
D.3.7 End of transmission.68
D.3.8 Stop-transmission order.68
D.3.9 Call clearing.68
ETSI
6 Final draft ETSI EN 300 392-1 V1.4.0 (2008-07)
D.3.9.1 Mobile originated.68
D.3.9.2 SwMI originated.69
D.4 Procedures - quasi-transmission trunked systems .70
D.4.1 Call set-up - on/off hook signalling.70
D.4.1.1 Call set-up - on/off hook signalling flow.70
D.4.1.2 Traffic assignment.71
D.4.2 Call set-up - direct set-up signalling.71
D.4.2.1 Call set-up - direct set-up signalling flow.71
D.4.2.2 Traffic assignment.72
D.4.3 Request-to-transmit.73
D.4.4 Response to request-to-transmit .74
D.4.5 Permission to transmit withdrawn .74
D.4.6 Permission to continue with withdrawn call.75
D.4.7 End of transmission request.75
D.4.8 Stop-transmission order.75
D.4.9 Call clearing.75
D.4.9.1 Mobile originated.75
D.4.9.2 SwMI originated.76
Annex E (informative): Group voice call scenarios.77
E.1 Procedures for message trunked systems .77
E.1.1 General.77
E.1.2 Call set-up.78
E.1.2.1 Call set-up flow.78
E.1.2.2 Traffic channel assignment.79
E.1.3 Request-to-transmit.79
E.1.4 Response to request-to-transmit .80
E.1.5 Permission to transmit withdrawn .81
E.1.6 Permission to continue with withdrawn call.81
E.1.7 End of transmission.81
E.1.8 Stop-transmission order.81
E.1.9 Call clearing.82
E.1.9.1 Mobile originated.82
E.1.9.2 SwMI originated.82
E.2 Procedures for transmission trunked systems.82
E.2.1 General.82
E.2.2 Call set-up.83
E.2.2.1 Call set-up flow.83
E.2.2.2 Traffic channel assignment.84
E.2.3 Request-to-transmit.84
E.2.4 Response to request-to-transmit .85
E.2.5 Permission to transmit withdrawn .86
E.2.6 Permission to continue with withdrawn call.86
E.2.7 End of transmission.86
E.2.8 Stop-transmission order.86
E.2.9 Call clearing.86
E.2.9.1 Mobile originated.86
E.2.9.2 SwMI originated.87
E.3 Procedures for quasi-transmission trunked systems.87
E.3.1 General.87
E.3.2 Call set-up.88
E.3.2.1 Call set-up flow.88
E.3.2.2 Traffic channel assignment.89
E.3.3 Request-to-transmit.89
E.3.4 Response to request-to-transmit .90
E.3.5 Permission to transmit withdrawn .90
E.3.6 Permission to continue with withdrawn call.90
E.3.7 End of transmission.91
E.3.8 Stop-transmission order.91
ETSI
7 Final draft ETSI EN 300 392-1 V1.4.0 (2008-07)
E.3.9 Call clearing.91
E.3.9.1 Mobile originated.91
E.3.9.2 SwMI originated.92
Annex F (informative): Priority functions for circuit mode services .93
F.1 Introduction.93
F.2 Priority requirements.93
F.2.1 Access priority.93
F.2.2 Call type priority .94
F.2.3 Queue priority.94
F.2.4 Pre-emptive priority.94
F.2.5 Call retention priority .94
F.2.6 Subscriber priority.94
F.3 Mechanisms for supporting priority.94
F.4 Supplementary service activation and invocation .95
Annex G (informative): Mobility Management (MM) in MS.96
G.1 Introduction.96
G.2 Overview of MM relations and procedures.96
G.3 Stimuli of MM.97
G.3.1 Stimulation through TNMM-SAP.97
G.3.2 Stimulation through LMM-SAP.98
G.3.3 Stimulation through peer MM.98
G.3.4 Other stimulation.98
G.4 Outputs from MM .98
G.4.1 Output through TNMM-SAP .98
G.4.2 Outputs through LMM-SAP.99
G.4.3 Output to peer MM.99
G.5 Database requirement.99
G.6 MM procedures.99
G.6.1 Registration.99
G.6.1.1 Registration at roaming.99
G.6.1.1.1 Implicit registration.99
G.6.1.1.2 Registration area.100
G.6.1.1.3 Registration procedure.100
G.6.1.1.4 Registration with authentication.101
G.6.1.1.5 Registration with identity exchange.102
G.6.1.2 Registration at migration.103
G.6.1.2.1 Registration with identity exchange.103
G.6.1.2.2 Registration with authentication.105
G.6.1.3 Network initiated registration .106
G.6.1.4 TEI request.106
G.6.2 Authentication.106
G.6.2.1 Network initiated authentication.106
G.6.2.2 MS initiated authentication.107
G.6.3 De-registration.108
G.6.4 Periodic registration.108
G.6.5 Disable/enable .108
G.6.5.1 Temporary disable.108
G.6.5.2 Enable.108
G.6.5.3 Permanently disable.109
G.6.6 Energy economy mode change.109
G.7 Downloading of group identiti
...

European Standard (Telecommunications series)

Terrestrial Trunked Radio (TETRA);
Voice plus Data (V+D);
Part 1: General network design

2 ETSI EN 300 392-1 V1.4.1 (2009-01)

Reference
REN/TETRA-03190
Keywords
air interface, TETRA, V+D
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: [phone]  Fax: [phone]

Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88

Important notice
Individual copies of the present document can be downloaded from:
http://www.etsi.org
The present document may be made available in more than one electronic version or in print. In any case of existing or
perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF).
In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive
within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
http://portal.etsi.org/chaircor/ETSI_support.asp
Copyright Notification
No part may be reproduced except as authorized by written permission.
The copyright and the foregoing restriction extend to reproduction in all media.

© European Telecommunications Standards Institute 2009.
All rights reserved.
TM TM TM TM
DECT , PLUGTESTS , UMTS , TIPHON , the TIPHON logo and the ETSI logo are Trade Marks of ETSI registered
for the benefit of its Members.
TM
3GPP is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners.
LTE™ is a Trade Mark of ETSI currently being registered
for the benefit of its Members and of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI
3 ETSI EN 300 392-1 V1.4.1 (2009-01)
Contents
Intellectual Property Rights . 12
Foreword . 12
1 Scope . 14
2 References . 14
2.1 Normative references . 15
2.2 Informative references . 15
3 Definitions, symbols and abbreviations . 16
3.1 Definitions . 16
3.2 Symbols . 21
3.3 Abbreviations . 22
4 Circuit mode reference points . 24
5 Packet mode reference points . 24
6 Protocol architecture for V+D . 24
7 Addressing and identities . 24
7.1 Introduction . 24
7.2 Subscriber identities . 26
7.2.1 General . 26
7.2.2 TSI . 27
7.2.3 SSI . 28
7.2.4 Composition of subscriber identities . 28
7.2.5 Allocation principles for subscriber identities . 29
7.2.6 Use of subscriber identities . 29
7.2.7 NSAP addresses . 30
7.2.8 Installation of TSIs. 30
7.3 TETRA Management Identity (TMI) . 30
7.3.1 General . 30
7.3.2 Composition of management identities. 31
7.3.3 Use of management identities . 31
7.4 Network layer SAP (NSAP) addresses . 31
7.4.1 General . 31
7.4.2 Static binding . 31
7.4.3 Dynamic binding . 32
7.4.3.1 General . 32
7.4.3.2 Structure and contents of NSAP addresses . 32
7.4.3.3 Use of NSAP addresses . 32
7.4.3.4 Binding of NSAP addresses . 32
7.5 TETRA Equipment Identity (TEI) . 32
7.5.1 General . 32
7.5.2 Contents of TEI . 33
7.5.3 Allocation principles for TEI . 33
7.5.4 Use of TEI. 33
7.6 Mobile Network Identity (MNI) . 34
7.6.1 Contents of MNI . 34
7.7 Layer 2 addresses and labels . 34
7.7.1 Overview . 34
7.7.2 Event labelling . 34
7.7.3 Scrambling labelling . 34
7.7.4 Use and implementation of layer 2 addresses . 35
7.7.4.1 General requirement . 35
7.7.4.2 Implementation of event labels . 35
7.7.4.3 Implementation of scrambling labels . 35
7.7.5 Use of identities for V+D control channels . 35
ETSI
4 ETSI EN 300 392-1 V1.4.1 (2009-01)
7.7.6 Labelling of packet channels . 36
7.7.6.1 Use of identities for uplink data transfers . 36
7.7.6.2 Use of identities for downlink data transfers . 36
7.7.7 System information broadcast. 37
7.7.8 Reserved value of group address for user information broadcast . 37
7.8 Use of individual addresses . 37
7.8.1 Air interface addressing functions . 37
7.8.2 Address placement in primitives and PDUs . 37
7.8.2.1 Use of ISSI at layer 2 . 37
7.8.2.2 Use of ITSI/ISSI at layer 3 . 39
7.8.2.2.1 Void . 39
7.8.2.2.2 Use of ITSI/ISSI by CMCE . 39
7.8.3 Routing principles . 40
7.8.3.1 Routing of intra-TETRA calls (within one TETRA network) . 40
7.8.3.2 Routing of inter-TETRA calls (between two TETRA networks) . 40
7.8.3.3 Routing of external calls (to/from non-TETRA networks) . 41
7.8.4 Address and identity comparison . 41
7.9 Addressing in interworking and roaming with other telecommunication networks . 41
8 Circuit mode basic services . 41
9 Mobility Management (MM) in MS . 42
10 MLE mobility scenarios and functionalities. 42
11 Technical realization of SDS . 42
12 Void . 42
13 Void . 42
14 General on supplementary services . 42
Annex A (informative): Circuit mode reference points. 43
A.1 Introduction . 43
A.2 Reference configuration . 43
A.2.1 Configuration examples of TETRA LMNs . 44
A.3 TETRA LMN access . 45
A.3.1 MS access . 45
A.3.1.1 MS functional groups. 45
A.3.1.2 MS access points and reference points . 45
A.3.2 Void . 46
A.3.3 Inter System Interface (ISI) access . 46
A.3.4 Location of TETRA functionality . 46
A.3.5 TETRA terminals . 46
Annex B (informative): Protocol architecture for V+D . 47
B.1 Introduction . 47
B.2 Mobile/base protocol architecture . 47
B.2.1 Overview . 47
B.2.2 Air interface layer 1 . 47
B.2.3 Air interface layer 2 . 48
B.2.3.1 Medium Access Control (MAC) . 48
B.2.3.2 Logical Link Control (LLC) . 50
B.2.4 Air interface layer 3 . 50
B.2.4.1 Mobile/Base Link control Entity (MLE/BLE) . 50
B.2.4.2 Sub-Network Access Functions (SNAF) . 51
B.2.4.2.1 Mobility Management (MM) . 51
B.2.4.2.2 Circuit Mode Control Entity (CMCE). 51
B.2.4.2.3 Packet data handling . 52
B.2.4.2.4 TETRA packet data protocol (PDP) . 52
ETSI
5 ETSI EN 300 392-1 V1.4.1 (2009-01)
B.2.4.2.5 Void. 52
B.2.5 Mobile/base protocol stack . 52
B.3 Lower Layer Management Entity (LLME) and other layers interaction . 53
B.3.1 General description. 53
Annex C (informative): Overview of circuit mode basic services . 54
C.1 Introduction . 54
C.2 Functional groupings in circuit switched mode calls . 54
C.2.1 Circuit switched call control, C-plane . 54
C.2.2 Circuit switched call, user data, U-plane . 54
C.3 Protocols . 54
C.3.1 TNP1 . 54
C.3.2 Void . 54
C.3.3 TNP3 . 54
C.3.4 TNP4 . 55
C.3.5 AI1. 55
C.3.6 AI2. 55
C.3.7 TLC1 . 55
C.3.8 V.24T . 55
C.4 Example configuration . 55
C.4.1 MS to MS . 55
C.4.2 Void . 56
C.4.3 Void . 56
C.4.4 MS to MS over ISI . 56
Annex D (informative): Individual circuit mode call scenarios. 58
D.1 Introduction . 58
D.2 Procedures - message trunked systems . 58
D.2.1 Call set-up - on/off hook signalling . 58
D.2.1.1 Call set-up - on/off hook signalling flow . 58
D.2.1.2 Traffic channel assignment . 59
D.2.2 Call set-up - direct set-up signalling . 59
D.2.2.1 Call set-up - direct set-up signalling flow . 59
D.2.2.2 Traffic channel assignment . 60
D.2.3 Request-to-transmit . 61
D.2.4 Response to request-to-transmit . 62
D.2.5 Permission to transmit withdrawn . 62
D.2.6 Permission to continue with withdrawn call . 62
D.2.7 End of transmission . 62
D.2.8 Stop-transmission order . 62
D.2.9 Call clearing . 63
D.2.9.1 Mobile originated . 63
D.2.9.2 SwMI originated . 64
D.3 Procedures - transmission trunked systems . 64
D.3.1 Call set-up - on/off hook signalling . 64
D.3.1.1 Call set-up - on/off hook signalling flow . 64
D.3.1.2 Traffic assignment . 65
D.3.2 Call set-up - direct set-up signalling . 65
D.3.2.1 Call set-up - direct set-up signalling flow . 65
D.3.2.2 Traffic channel assignment . 66
D.3.3 Request-to-transmit . 66
D.3.4 Response to request-to-transmit . 67
D.3.5 Permission to transmit withdrawn . 68
D.3.6 Permission to continue with withdrawn call . 68
D.3.7 End of transmission . 68
D.3.8 Stop-transmission order . 68
D.3.9 Call clearing . 68
ETSI
6 ETSI EN 300 392-1 V1.4.1 (2009-01)
D.3.9.1 Mobile originated . 68
D.3.9.2 SwMI originated . 69
D.4 Procedures - quasi-transmission trunked systems . 70
D.4.1 Call set-up - on/off hook signalling . 70
D.4.1.1 Call set-up - on/off hook signalling flow . 70
D.4.1.2 Traffic assignment . 71
D.4.2 Call set-up - direct set-up signalling . 71
D.4.2.1 Call set-up - direct set-up signalling flow . 71
D.4.2.2 Traffic assignment . 72
D.4.3 Request-to-transmit . 73
D.4.4 Response to request-to-transmit . 74
D.4.5 Permission to transmit withdrawn . 74
D.4.6 Permission to continue with withdrawn call . 75
D.4.7 End of transmission request. 75
D.4.8 Stop-transmission order . 75
D.4.9 Call clearing . 75
D.4.9.1 Mobile originated . 75
D.4.9.2 SwMI originated . 76
Annex E (informative): Group voice call scenarios . 77
E.1 Procedures for message trunked systems . 77
E.1.1 General . 77
E.1.2 Call set-up . 78
E.1.2.1 Call set-up flow . 78
E.1.2.2 Traffic channel assignment . 79
E.1.3 Request-to-transmit . 79
E.1.4 Response to request-to-transmit . 80
E.1.5 Permission to transmit withdrawn . 81
E.1.6 Permission to continue with withdrawn call . 81
E.1.7 End of transmission . 81
E.1.8 Stop-transmission order . 81
E.1.9 Call clearing . 82
E.1.9.1 Mobile originated . 82
E.1.9.2 SwMI originated . 82
E.2 Procedures for transmission trunked systems . 82
E.2.1 General . 82
E.2.2 Call set-up . 83
E.2.2.1 Call set-up flow . 83
E.2.2.2 Traffic channel assignment . 84
E.2.3 Request-to-transmit . 84
E.2.4 Response to request-to-transmit . 85
E.2.5 Permission to transmit withdrawn . 86
E.2.6 Permission to continue with withdrawn call . 86
E.2.7 End of transmission . 86
E.2.8 Stop-transmission order . 86
E.2.9 Call clearing . 86
E.2.9.1 Mobile originated . 86
E.2.9.2 SwMI originated . 87
E.3 Procedures for quasi-transmission trunked systems . 87
E.3.1 General . 87
E.3.2 Call set-up . 88
E.3.2.1 Call set-up flow . 88
E.3.2.2 Traffic channel assignment . 89
E.3.3 Request-to-transmit . 89
E.3.4 Response to request-to-transmit . 90
E.3.5 Permission to transmit withdrawn . 90
E.3.6 Permission to continue with withdrawn call . 90
E.3.7 End of transmission . 91
E.3.8 Stop-transmission order . 91
ETSI
7 ETSI EN 300 392-1 V1.4.1 (2009-01)
E.3.9 Call clearing . 91
E.3.9.1 Mobile originated . 91
E.3.9.2 SwMI originated . 92
Annex F (informative): Priority functions for circuit mode services . 93
F.1 Introduction . 93
F.2 Priority requirements . 93
F.2.1 Access priority . 93
F.2.2 Call type priority . 94
F.2.3 Queue priority . 94
F.2.4 Pre-emptive priority . 94
F.2.5 Call retention priority . 94
F.2.6 Subscriber priority . 94
F.3 Mechanisms for supporting priority . 94
F.4 Supplementary service activation and invocation . 95
Annex G (informative): Mobility Management (MM) in MS . 96
G.1 Introduction . 96
G.2 Overview of MM relations and procedures . 96
G.3 Stimuli of MM . 97
G.3.1 Stimulation through TNMM-SAP . 97
G.3.2 Stimulation through LMM-SAP . 98
G.3.3 Stimulation through peer MM . 98
G.3.4 Other stimulation . 98
G.4 Outputs from MM . 98
G.4.1 Output through TNMM-SAP . 98
G.4.2 Outputs through LMM-SAP . 99
G.4.3 Output to peer MM . 99
G.5 Database requirement . 99
G.6 MM procedures . 99
G.6.1 Registration . 99
G.6.1.1 Registration at roaming . 99
G.6.1.1.1 Implicit registration . 99
G.6.1.1.2 Registration area . 100
G.6.1.1.3 Registration procedure . 100
G.6.1.1.4 Registration with authentication . 101
G.6.1.1.5 Registration with identity exchange . 102
G.6.1.2 Registration at migration . 103
G.6.1.2.1 Registration with identity exchange . 103
G.6.1.2.2 Registration with authentication . 105
G.6.1.3 Network initiated registration . 106
G.6.1.4 TEI request. 106
G.6.2 Authentication . 106
G.6.2.1 Network initiated authentication . 106
G.6.2.2 MS initiated authentication . 107
G.6.3 De-registration . 108
G.6.4 Periodic registration . 108
G.6.5 Disable/enable . 108
G.6.5.1 Temporary disable .
...

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Prizemni snopovni radio (TETRA) - Govor in podatki (V+D) - 1. del: Splošna zasnova omrežjaTerrestrial Trunked Radio (TETRA) - Voice plus Data (V+D) - Part 1: General network design33.070.10Prizemni snopovni radio (TETRA)Terrestrial Trunked Radio (TETRA)ICS:Ta slovenski standard je istoveten z:EN 300 392-1 Version 1.4.1SIST EN 300 392-1 V1.4.1:2009en01-april-2009SIST EN 300 392-1 V1.4.1:2009SLOVENSKI
STANDARD
ETSI ETSI EN 300 392-1 V1.4.1 (2009-01) 2
Reference REN/TETRA-03190 Keywords air interface, TETRA, V+D ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: [phone]
Fax: [phone]
Siret N° 348 623 562 00017 - NAF 742 C Association à but non lucratif enregistrée à la Sous-Préfecture de Grasse (06) N° 7803/88
Important notice Individual copies of the present document can be downloaded from: http://www.etsi.org The present document may be made available in more than one electronic version or in print. In any case of existing or perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF). In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at http://portal.etsi.org/tb/status/status.asp If you find errors in the present document, please send your comment to one of the following services: http://portal.etsi.org/chaircor/ETSI_support.asp Copyright Notification No part may be reproduced except as authorized by written permission. The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2009. All rights reserved.
DECTTM, PLUGTESTSTM, UMTSTM, TIPHONTM, the TIPHON logo and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. LTE™ is a Trade Mark of ETSI currently being registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association. SIST EN 300 392-1 V1.4.1:2009

ETSI ETSI EN 300 392-1 V1.4.1 (2009-01) 3 Contents Intellectual Property Rights . 12 Foreword . 12 1 Scope . 14 2 References . 14 2.1 Normative references . 15 2.2 Informative references . 15 3 Definitions, symbols and abbreviations . 16 3.1 Definitions . 16 3.2 Symbols . 21 3.3 Abbreviations . 22 4 Circuit mode reference points . 24 5 Packet mode reference points . 24 6 Protocol architecture for V+D . 24 7 Addressing and identities . 24 7.1 Introduction . 24 7.2 Subscriber identities . 26 7.2.1 General . 26 7.2.2 TSI . 27 7.2.3 SSI . 28 7.2.4 Composition of subscriber identities . 28 7.2.5 Allocation principles for subscriber identities . 29 7.2.6 Use of subscriber identities . 29 7.2.7 NSAP addresses . 30 7.2.8 Installation of TSIs. 30 7.3 TETRA Management Identity (TMI) . 30 7.3.1 General . 30 7.3.2 Composition of management identities. 31 7.3.3 Use of management identities . 31 7.4 Network layer SAP (NSAP) addresses . 31 7.4.1 General . 31 7.4.2 Static binding . 31 7.4.3 Dynamic binding . 32 7.4.3.1 General . 32 7.4.3.2 Structure and contents of NSAP addresses . 32 7.4.3.3 Use of NSAP addresses . 32 7.4.3.4 Binding of NSAP addresses . 32 7.5 TETRA Equipment Identity (TEI) . 32 7.5.1 General . 32 7.5.2 Contents of TEI . 33 7.5.3 Allocation principles for TEI . 33 7.5.4 Use of TEI. 33 7.6 Mobile Network Identity (MNI) . 34 7.6.1 Contents of MNI . 34 7.7 Layer 2 addresses and labels . 34 7.7.1 Overview . 34 7.7.2 Event labelling . 34 7.7.3 Scrambling labelling . 34 7.7.4 Use and implementation of layer 2 addresses . 35 7.7.4.1 General requirement . 35 7.7.4.2 Implementation of event labels . 35 7.7.4.3 Implementation of scrambling labels . 35 7.7.5 Use of identities for V+D control channels . 35 SIST EN 300 392-1 V1.4.1:2009

ETSI ETSI EN 300 392-1 V1.4.1 (2009-01) 4 7.7.6 Labelling of packet channels . 36 7.7.6.1 Use of identities for uplink data transfers . 36 7.7.6.2 Use of identities for downlink data transfers . 36 7.7.7 System information broadcast. 37 7.7.8 Reserved value of group address for user information broadcast . 37 7.8 Use of individual addresses . 37 7.8.1 Air interface addressing functions . 37 7.8.2 Address placement in primitives and PDUs . 37 7.8.2.1 Use of ISSI at layer 2 . 37 7.8.2.2 Use of ITSI/ISSI at layer 3 . 39 7.8.2.2.1 Void . 39 7.8.2.2.2 Use of ITSI/ISSI by CMCE . 39 7.8.3 Routing principles . 40 7.8.3.1 Routing of intra-TETRA calls (within one TETRA network) . 40 7.8.3.2 Routing of inter-TETRA calls (between two TETRA networks) . 40 7.8.3.3 Routing of external calls (to/from non-TETRA networks) . 41 7.8.4 Address and identity comparison . 41 7.9 Addressing in interworking and roaming with other telecommunication networks . 41 8 Circuit mode basic services . 41 9 Mobility Management (MM) in MS . 42 10 MLE mobility scenarios and functionalities. 42 11 Technical realization of SDS . 42 12 Void . 42 13 Void . 42 14 General on supplementary services . 42 Annex A (informative): Circuit mode reference points. 43 A.1 Introduction . 43 A.2 Reference configuration . 43 A.2.1 Configuration examples of TETRA LMNs . 44 A.3 TETRA LMN access . 45 A.3.1 MS access . 45 A.3.1.1 MS functional groups. 45 A.3.1.2 MS access points and reference points . 45 A.3.2 Void . 46 A.3.3 Inter System Interface (ISI) access . 46 A.3.4 Location of TETRA functionality . 46 A.3.5 TETRA terminals . 46 Annex B (informative): Protocol architecture for V+D . 47 B.1 Introduction . 47 B.2 Mobile/base protocol architecture . 47 B.2.1 Overview . 47 B.2.2 Air interface layer 1 . 47 B.2.3 Air interface layer 2 . 48 B.2.3.1 Medium Access Control (MAC) . 48 B.2.3.2 Logical Link Control (LLC) . 50 B.2.4 Air interface layer 3 . 50 B.2.4.1 Mobile/Base Link control Entity (MLE/BLE) . 50 B.2.4.2 Sub-Network Access Functions (SNAF) . 51 B.2.4.2.1 Mobility Management (MM) . 51 B.2.4.2.2 Circuit Mode Control Entity (CMCE). 51 B.2.4.2.3 Packet data handling . 52 B.2.4.2.4 TETRA packet data protocol (PDP) . 52 SIST EN 300 392-1 V1.4.1:2009

ETSI ETSI EN 300 392-1 V1.4.1 (2009-01) 5 B.2.4.2.5 Void. 52 B.2.5 Mobile/base protocol stack . 52 B.3 Lower Layer Management Entity (LLME) and other layers interaction . 53 B.3.1 General description. 53 Annex C (informative): Overview of circuit mode basic services . 54 C.1 Introduction . 54 C.2 Functional groupings in circuit switched mode calls . 54 C.2.1 Circuit switched call control, C-plane . 54 C.2.2 Circuit switched call, user data, U-plane . 54 C.3 Protocols . 54 C.3.1 TNP1 . 54 C.3.2 Void . 54 C.3.3 TNP3 . 54 C.3.4 TNP4 . 55 C.3.5 AI1. 55 C.3.6 AI2. 55 C.3.7 TLC1 . 55 C.3.8 V.24T . 55 C.4 Example configuration . 55 C.4.1 MS to MS . 55 C.4.2 Void . 56 C.4.3 Void . 56 C.4.4 MS to MS over ISI . 56 Annex D (informative): Individual circuit mode call scenarios. 58 D.1 Introduction . 58 D.2 Procedures - message trunked systems . 58 D.2.1 Call set-up - on/off hook signalling . 58 D.2.1.1 Call set-up - on/off hook signalling flow . 58 D.2.1.2 Traffic channel assignment . 59 D.2.2 Call set-up - direct set-up signalling . 59 D.2.2.1 Call set-up - direct set-up signalling flow . 59 D.2.2.2 Traffic channel assignment . 60 D.2.3 Request-to-transmit . 61 D.2.4 Response to request-to-transmit . 62 D.2.5 Permission to transmit withdrawn . 62 D.2.6 Permission to continue with withdrawn call . 62 D.2.7 End of transmission . 62 D.2.8 Stop-transmission order . 62 D.2.9 Call clearing . 63 D.2.9.1 Mobile originated . 63 D.2.9.2 SwMI originated . 64 D.3 Procedures - transmission trunked systems . 64 D.3.1 Call set-up - on/off hook signalling . 64 D.3.1.1 Call set-up - on/off hook signalling flow . 64 D.3.1.2 Traffic assignment . 65 D.3.2 Call set-up - direct set-up signalling . 65 D.3.2.1 Call set-up - direct set-up signalling flow . 65 D.3.2.2 Traffic channel assignment . 66 D.3.3 Request-to-transmit . 66 D.3.4 Response to request-to-transmit . 67 D.3.5 Permission to transmit withdrawn . 68 D.3.6 Permission to continue with withdrawn call . 68 D.3.7 End of transmission . 68 D.3.8 Stop-transmission order . 68 D.3.9 Call clearing . 68 SIST EN 300 392-1 V1.4.1:2009

ETSI ETSI EN 300 392-1 V1.4.1 (2009-01) 6 D.3.9.1 Mobile originated . 68 D.3.9.2 SwMI originated . 69 D.4 Procedures - quasi-transmission trunked systems . 70 D.4.1 Call set-up - on/off hook signalling . 70 D.4.1.1 Call set-up - on/off hook signalling flow . 70 D.4.1.2 Traffic assignment . 71 D.4.2 Call set-up - direct set-up signalling . 71 D.4.2.1 Call set-up - direct set-up signalling flow . 71 D.4.2.2 Traffic assignment . 72 D.4.3 Request-to-transmit . 73 D.4.4 Response to request-to-transmit . 74 D.4.5 Permission to transmit withdrawn . 74 D.4.6 Permission to continue with withdrawn call . 75 D.4.7 End of transmission request. 75 D.4.8 Stop-transmission order . 75 D.4.9 Call clearing . 75 D.4.9.1 Mobile originated . 75 D.4.9.2 SwMI originated . 76 Annex E (informative): Group voice call scenarios . 77 E.1 Procedures for message trunked systems . 77 E.1.1 General . 77 E.1.2 Call set-up . 78 E.1.2.1 Call set-up flow . 78 E.1.2.2 Traffic channel assignment . 79 E.1.3 Request-to-transmit . 79 E.1.4 Response to request-to-transmit . 80 E.1.5 Permission to transmit withdrawn . 81 E.1.6 Permission to continue with withdrawn call . 81 E.1.7 End of transmission . 81 E.1.8 Stop-transmission order . 81 E.1.9 Call clearing . 82 E.1.9.1 Mobile originated . 82 E.1.9.2 SwMI originated . 82 E.2 Procedures for transmission trunked systems . 82 E.2.1 General . 82 E.2.2 Call set-up . 83 E.2.2.1 Call set-up flow . 83 E.2.2.2 Traffic channel assignment . 84 E.2.3 Request-to-transmit . 84 E.2.4 Response to request-to-transmit . 85 E.2.5 Permission to transmit withdrawn . 86 E.2.6 Permission to continue with withdrawn call . 86 E.2.7 End of transmission . 86 E.2.8 Stop-transmission order . 86 E.2.9 Call clearing . 86 E.2.9.1 Mobile originated . 86 E.2.9.2 SwMI originated . 87 E.3 Procedures for quasi-transmission trunked systems . 87 E.3.1 General . 87 E.3.2 Call set-up . 88 E.3.2.1 Call set-up flow . 88 E.3.2.2 Traffic channel assignment . 89 E.3.3 Request-to-transmit . 89 E.3.4 Response to request-to-transmit . 90 E.3.5 Permission to transmit withdrawn . 90 E.3.6 Permission to continue with withdrawn call . 90 E.3.7 End of transmission . 91 E.3.8 Stop-transmission order . 91 SIST EN 300 392-1 V1.4.1:2009

ETSI ETSI EN 300 392-1 V1.4.1 (2009-01) 7 E.3.9 Call clearing . 91 E.3.9.1 Mobile originated . 91 E.3.9.2 SwMI originated . 92 Annex F (informative): Priority functions for circuit mode services . 93 F.1 Introduction . 93 F.2 Priority requirements . 93 F.2.1 Access priority . 93 F.2.2 Call type priority . 94 F.2.3 Queue priority . 94 F.2.4 Pre-emptive priority . 94 F.2.5 Call retention priority . 94 F.2.6 Subscriber priority . 94 F.3 Mechanisms for supporting priority . 94 F.4 Supplementary service activation and invocation . 95 Annex G (informative): Mobility Management (MM) in MS . 96 G.1 Introduction . 96 G.2 Overview of MM relations and procedures . 96 G.3 Stimuli of MM . 97 G.3.1 Stimulation through TNMM-SAP . 97 G.3.2 Stimulation through LMM-SAP . 98 G.3.3 Stimulation through peer MM . 98 G.3.4 Other stimulation . 98 G.4 Outputs from MM . 98 G.4.1 Output through TNMM-SAP . 98 G.4.2 Outputs through LMM-SAP . 99 G.4.3 Output to peer MM . 99 G.5 Database requirement . 99 G.6 MM procedures . 99 G.6.1 Registration . 99 G.6.1.1 Registration at roaming . 99 G.6.1.1.1 Implicit registration . 99 G.6.1.1.2 Registration area . 100 G.6.1.1.3 Registration procedure . 100 G.6.1.1.4 Registration with authentication . 101 G.6.1.1.5 Registration with identity exchange . 102 G.6.1.2 Registration at migration . 103 G.6.1.2.1 Registration with identity exchange . 103 G.6.1.2.2 Registration with authentication . 105 G.6.1.3 Network initiated registration . 106 G.6.1.4 TEI request. 106 G.6.2 Authentication . 106 G.6.2.1 Network initiated authentication . 106 G.6.2.2 MS initiated authentication . 107 G.6.3 De-registration . 108 G.6.4 Periodic registration . 108 G.6.5 Disable/enable . 108 G.6.5.1 Temporary disable .
...