iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
SIST

SIST EN 13071-2:2008/AC:2010

(Corrigendum)

Stationary waste containers up to 5 000 l, top lifted and bottom emptied - Part 2: Additional requirements for underground or partly underground systems

Stationary waste containers up to 5 000 l, top lifted and bottom emptied - Part 2: Additional requirements for underground or partly underground systems

TC - Correction of unit in the 1st paragraph of 4.3.2 and correction of value in the 1st paragraph of 6.2.2.2

Stationäre Abfallsammelbehälter bis 5 000 l, mit Behälteraufnahme an der Oberseite und Bodenentleerung - Teil 2: Zusätzliche Anforderungen für unterirdische oder teilweise unterirdische Systeme

Conteneurs fixes à déchets de capacité inférieure ou égale à 5 000 l, levés par le haut et vidés par le bas - Partie 2: Exigences complémentaires relatives aux systèmes enterrés ou semi-enterrés

Nepremični zabojniki za odpadke do 5000 l, ki se dvigujejo zgoraj in praznijo spodaj - 2. del: Dodatne zahteve za podzemne ali delno podzemne sisteme

Ta dokument opredeljuje dodatne zahteve za podzemne ali delno podzemne sisteme, ki se dvigujejo zgoraj in praznijo spodaj in se uporabljajo za zbiranje trdnih nenevarnih odpadkov s kapaciteto do 5.000 l.

General Information

Status
Withdrawn
Publication Date
08-Apr-2010
Withdrawal Date
12-Dec-2013
ICS
13.030.40 - Installations and equipment for waste disposal and treatment
Technical Committee
I13 - Imaginarni 13
Current Stage
9900 - Withdrawal (Adopted Project)
Start Date
13-Dec-2013
Due Date
05-Jan-2014
Completion Date
13-Dec-2013
Ref Project
EN 13071-2:2008/AC:2010 - Stationary waste containers up to 5 000 l, top lifted and bottom emptied - Part 2: Additional requirements for underground or partly underground systems

Relations

Corrects
SIST EN 13071-2:2008 - Stationary waste containers up to 5 000 l, top lifted and bottom emptied - Part 2: Additional requirements for underground or partly underground systems
Effective Date
01-May-2010
Consolidated By
SIST EN 13071-2:2008+A1:2014 - Stationary waste containers up to 5 000 l, top lifted and bottom emptied - Part 2: Additional requirements for underground or partly underground systems
Effective Date
18-Jan-2023
Consolidated By
SIST EN 13071-2:2008+A1:2014 - Stationary waste containers up to 5 000 l, top lifted and bottom emptied - Part 2: Additional requirements for underground or partly underground systems
Effective Date
19-Jan-2023
Consolidated By
SIST EN 13071-2:2008+A1:2014 - Stationary waste containers up to 5 000 l, top lifted and bottom emptied - Part 2: Additional requirements for underground or partly underground systems
Effective Date
01-Jan-2014

Buy Standard

EN 13071-2:2008/AC:2010EN 13071-2:2008/AC:2010
PreviousNext
Corrigendum
EN 13071-2:2008/AC:2010
English language
2 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.LVWHPHStationäre Abfallsammelbehälter bis 5 000 l, mit Behälteraufnahme an der Oberseite und Bodenentleerung - Teil 2: Zusätzliche Anforderungen für unterirdische oder teilweise unterirdische SystemeConteneurs fixes à déchets de capacité inférieure ou égale à 5 000 l, levés par le haut et vidés par le bas - Partie 2: Exigences complémentaires relatives aux systèmes enterrés ou semi-enterrésStationary waste containers up to 5 000 l, top lifted and bottom emptied - Part 2: Additional requirements for underground or partly underground systems13.030.40Naprave in oprema za odstranjevanje in obdelavo odpadkovInstallations and equipment for waste disposal and treatmentICS:Ta slovenski standard je istoveten z:EN 13071-2:2008/AC:2010SIST EN 13071-2:2008/AC:2010en,de01-maj-2010SIST EN 13071-2:2008/AC:2010SLOVENSKI
STANDARD



SIST EN 13071-2:2008/AC:2010



EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 13071-2:2008/AC
March 2010
Mars 2010
März 2010 ICS 13.030.40 English version Version Française Deutsche Fassung
Stationary waste containers up to 5 000 l, top lifted and bottom emptied - Part 2: Additional requirements for underground or partly underground systems
Conteneurs fixes à déchets de capacité inférieure ou égale à 5 000 l, levés par le haut et vidés par le bas - Partie 2: Exigences complémentaires relatives aux systèmes enterrés
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

SIST
SIST EN 17367:2023(Main)
Waste Management - Data communication between communication management system and the back office system for stationary waste collection containers - Functional specification and the semantic data model
EN 17367:2023

This document defines the standard for exchanging stationary waste collection container information between the collection container system and the back-office systems.
This document defines the way to exchange data between the "Communication Management System" of the collection container and the "Back-Office Systems".
The exchange of data between the "Collection Container Systems" and the "Communication Management Systems" or the "Back-Office Systems" is excluded.
This document targets two streams of information in the waste processing industry:
-   The processing of transactions and system information for the deposit of waste from the communication management systems to the back office systems.
-   The processing of authorization and configuration information from the back-office systems to the communication management systems.

  • Standard
    25 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    24 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 1501-4:2023(Main)
Refuse collection vehicles - General requirements and safety requirements - Part 4: Noise test code for refuse collection vehicles
EN 1501-4:2023

This European Standard provides all of the information required in order to efficiently perform, and in standardized conditions, the determination, the declaration and the verification of noise emission values of refuse collection vehicles.
The use of this annex ensures the reproducibility of the determination of noise emission values within the limits established for the accuracy grade of the basic standard used to determine noise emission values. The methods used to determine these noise emission values, corresponding to this normative annex, are grade 2 accuracy measurement methods.
This standard deals with the noise measurement conditions for the types of RCVs defined and described in the standards of the EN 1501 series
This European Standard applies to machines which are manufactured after the date of approval of this standard by CEN.

  • Standard
    23 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    19 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST-TP CWA 17866:2022(Main)
Key factors for the successful implementation of urban biowaste selective collection schemes
CWA 17866:2022

This CWA provides guidance for the implementation of biowaste selective collection schemes.
This CWA also paves the way to increase citizen engagement, as this is crucial for the successful implementation of urban biowaste selective collection schemes.
It is intended to be used by city managers and municipal waste managers with interest in implementing the selective collection of urban biowaste to produce high quality biowaste (i.e., minimal presence of non-required fractions) which can be then used in robust valorization processes with attractive business cases.

  • Standardization document
    19 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Technical report
    19 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 17443:2021(Main)
Winter service equipment - Brine production systems - Requirements and test methods
EN 17443:2021

This European standard specifies the essential requirements of stationary systems for production of brines for winter road maintenance and includes tests of these requirements. Battery limits: chloride and water inlet to the saturator, brine outlet to the spreading machine. Within the scope are storage and loading/unloading equipment also.
The following points are not covered by this standard:
   - System and construction requirements;
   - Requirements according national legislations.

  • Standard
    21 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    20 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 1501-1:2021(Main)
Refuse collection vehicles - General requirements and safety requirements - Part 1: Rear loaded refuse collection vehicles
EN 1501-1:2021

This document applies to rear loaded refuse collection vehicles (RCV), as defined in 3.2.
This document deals with all significant hazards, hazardous situations and events relevant to the rear loaded RCV, when it is used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer, throughout its foreseeable lifetime, as defined in Clause 4.
This document is applicable to the design and construction of the rear loaded RCV so as to ensure that it is fit for its function and can be operated, adjusted and maintained during its entire lifetime. It is not applicable to the end of life of the rear loaded RCV.
This document describes and defines the safety requirements of rear loaded RCVs excluding the interface tailgate/discharge door with the lifting device(s) and the lifting device(s) as illustrated in Figure A.1.
Safety requirements for the lifting device(s) and the interface with the tailgate/discharge door are defined in prEN 1501-5. Safety requirements for loader cranes are defined in EN 12999.
This European Standard is not applicable to:
-   operation in severe conditions, e.g. extreme environmental conditions such as:
-   below -25 °C and above +40 °C temperatures;
-   tropical environment;
-   wind velocity in excess of 75 km/h;
-   contaminating environment;
-   corrosive environment;
-   operation in potentially explosive atmospheres;
-   handling of loads the nature of which could lead to dangerous situations (e.g. hot refuses, acids and bases, radioactive materials, contaminated refuse, especially fragile loads, explosives);
-   operation on ships.
This document is not applicable to machinery which is manufactured before the date of publication of this document by CEN.

  • Standard
    78 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 1501-3:2021(Main)
Refuse collection vehicles - General requirements and safety requirements - Part 3: Front loaded refuse collection vehicles
EN 1501-3:2021

This document applies to front loaded refuse collection vehicle (RCV), as defined in 3.2 with closed system defined in 3.13.
This document deals with all significant hazards, hazardous situations and events relevant to the front loaded RCV, when it is used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer, throughout its foreseeable lifetime, as defined in Clause 4.
This document is applicable to the design and construction of the front loaded RCV so as to ensure that it is fitted for its function and can be operated adjusted and maintained during its entire lifetime. It is not applicable to the end of life of the front loaded RCV.
prEN 1501-3 describes and defines the safety requirements of front loaded RCV excluding the interface with the lifting device(s) and excluding the lifting device itself and excluding loader cranes, which could be mounted on the RCV.
Safety requirements for the lifting device(s), loader cranes and their interface to the RCV are defined in prEN 1501-5.
Safety requirements for loader cranes are defined in EN 12999. Additional requirements to loader cranes installed as a loading device for handling containers for refuse or recyclable material on RCVs are defined in prEN 1501 5.
This document also applies to compactors, operated on a truck for collecting purposes.
This document is not applicable to:
-   operation in severe conditions e.g. extreme environmental conditions such as:
-   below −25 °C and above +40 °C temperatures;
-   tropical environment;
-   wind velocity in excess of 75 km/h;
-   contaminating environment;
-   corrosive environment;
-   operation in potentially explosive atmospheres;
-   handling of loads the nature of which could lead to dangerous situations (e.g. hot refuses, acids and bases, radioactive materials, contaminated refuse, especially fragile loads, explosives);
-   operation on ships.
This document is not applicable to machinery which is manufactured before the date of publication of this document by CEN.

  • Standard
    54 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 1501-2:2021(Main)
Refuse collection vehicles - General requirements and safety requirements - Part 2: Side loaded refuse collection vehicles
EN 1501-2:2021

This document applies to side loaded refuse collection vehicle (RCV), as defined in prEN 1501-1.
This document deals with all significant hazards, hazardous situations and events relevant to the side loaded RCV, when it is used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer, throughout its foreseeable lifetime, as defined in Clause 4.
This document is applicable to the design and construction of the side loaded RCV so as to ensure that it is fit for its intended function and can be operated, moved, cleaned (including unblocking), adjusted and maintained during its entire lifetime. It is not applicable to the end of life of the side loaded RCV.
This document describes and defines the safety requirements of side loaded RCV excluding the interface with the lifting device(s) and excluding the lifting device itself and excluding loader cranes, which could be mounted on the RCV.
Safety requirements for the lifting device(s) including the loader cranes and the interface to the RCV are defined in prEN 1501-5.
Safety requirements for loader cranes are defined in EN 12999.
This document also applies to compactors, operated on a truck for collecting purposes.
This document is not applicable to:
-   below −25 °C and above +40 °C temperatures;
-   tropical environment;
-   wind velocity in excess of 75 km/h;
-   contaminating environment;
-   corrosive environment;
-   operation in potentially explosive atmospheres;
-   handling of loads the nature of which could lead to dangerous situations (e.g. hot refuses, acids and bases, radioactive materials, contaminated refuse, especially fragile loads, explosives);
-   operation on ships.
This document is not applicable to machinery which is manufactured before the date of publication of this document by CEN.

  • Standard
    62 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 1501-5:2021(Main)
Refuse collection vehicles - General requirements and safety requirements - Part 5: Lifting devices for refuse collection vehicles
EN 1501-5:2021

This document deals with all significant hazards, hazardous situations and events relevant to lifting devices used for the emptying of designated refuse containers into RCVs and their fitting onto the RCVs when they are used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer throughout their foreseeable lifetime as defined in Clause 4.
This document is applicable to the design and construction of the refuse container lifting devices and the mounting of other lifting devices so as to ensure that they are fitted for their function and can be operated, adjusted and maintained during their entire lifetime. It is not applicable to the end of life of the lifting devices.
This document describes and gives the safety requirements of the lifting devices for emptying refuse containers and their interfaces with the corresponding parts of the RCVs and will be used in conjunction with prEN 1501-1 for the rear, side and front loaded RCVs. It refers to EN 1501-4 for the noise test code.
This document is not applicable to:
-   operation in severe conditions e.g. extreme environmental conditions such as:
-   temperatures below −25 °C and above +40 °C;
-   tropical environment;
-   wind velocity in excess of 75 km/h;
-   contaminating environment;
-   corrosive environment;
-   operation in potentially explosive atmospheres;
-   lifting and transportation of persons;
-   emptying refuse containers other than those manufactured according to EN 840 (all parts), EN 12574 (all parts), EN 13071 (all parts), and those described as paladin, diamond, skip containers;
-   loading bulky refuse by means of platform or forks;
-   handling of loads the nature of which could lead to dangerous situations (e.g. hot refuses, acids and bases, radioactive materials, contaminated refuse, especially fragile loads, explosives);
-   operation on ships;
-   fitting and operation on stationary compactors.
This document is not applicable to machinery which is manufactured before the date of its publication by CEN.

  • Standard
    95 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 840-1:2020/AC:2021(Corrigendum)
Mobile waste and recycling containers - Part 1: Containers with 2 wheels with a capacity up to 400 l for comb lifting devices - Dimensions and design
EN 840-1:2020/AC:2020

2020-10-21 - TC - Addition of figure designations "A" and "B" in Figure 2

  • Corrigendum
    2 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 840-6:2020(Main)
Mobile waste and recycling containers - Part 6: Safety and health requirements
EN 840-6:2020

This European Standard provides the essential safety, health and ergonomic requirements for mobile waste and recycling containers according to EN 840-1 to EN 840-4, not including hazardous wastes containers.

  • Standard
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    8 pages
    English language
    sale 10% off
    e-Library read for
    1 day