SIST EN 746-1:2000/kprA1:2009
(Amendment)Industrial thermoprocessing equipment - Part 1: Common safety requirements for industrial thermoprocessing equipment
Industrial thermoprocessing equipment - Part 1: Common safety requirements for industrial thermoprocessing equipment
Industrielle Thermoprozessanlagen - Teil 1: Allgemeine Sicherheitsanforderungen an industrielle Thermoprozessanlagen
Equipements thermiques industriels - Partie 1: Prescriptions générales de sécurité pour les équipements thermiques industriels
Industrijska termoprocesna oprema - 1. del: Splošne varnostne zahteve za industrijsko termoprocesno opremo
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 746-1:2000/kprA1:2009
01-april-2009
Industrijska termoprocesna oprema - 1. del: Splošne varnostne zahteve za
industrijsko termoprocesno opremo
Industrial thermoprocessing equipment - Part 1: Common safety requirements for
industrial thermoprocessing equipment
Industrielle Thermoprozessanlagen - Teil 1: Allgemeine Sicherheitsanforderungen an
industrielle Thermoprozessanlagen
Equipements thermiques industriels - Partie 1: Prescriptions générales de sécurité pour
les équipements thermiques industriels
Ta slovenski standard je istoveten z: EN 746-1:1997/prA1
ICS:
25.180.01 ,QGXVWULMVNHSHþLQDVSORãQR Industrial furnaces in general
SIST EN 746-1:2000/kprA1:2009 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 746-1:2000/kprA1:2009
---------------------- Page: 2 ----------------------
SIST EN 746-1:2000/kprA1:2009
EUROPEAN STANDARD
FINAL DRAFT
EN 746-1:1997
NORME EUROPÉENNE
EUROPÄISCHE NORM
prA1
January 2009
ICS 25.180.01
English Version
Industrial thermoprocessing equipment - Part 1: Common safety
requirements for industrial thermoprocessing equipment
Equipements thermiques industriels - Partie 1: Industrielle Thermoprozessanlagen - Teil 1: Allgemeine
Prescriptions générales de sécurité pour les équipements Sicherheitsanforderungen an industrielle
thermiques industriels Thermoprozessanlagen
This draft amendment is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical Committee
CEN/TC 186.
This draft amendment A1, if approved, will modify the European Standard EN 746-1:1997. If this draft becomes an amendment, CEN
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this amendment
into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other language made
by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2009 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 746-1:1997/prA1:2009: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 746-1:2000/kprA1:2009
EN 746-1:1997/prA1:2009 (E)
Contents Page
Foreword.3
1 Modification to the Foreword .4
2 Modification to Clause 2, Normative references .4
2.1 Basic Standards.4
2.2 Group Safety Standards.5
2.3 Product Safety Standards.7
3 Modification to Annex A.10
4 Modification to Annex ZB .11
2
---------------------- Page: 4 ----------------------
SIST EN 746-1:2000/kprA1:2009
EN 746-1:1997/prA1:2009 (E)
Foreword
This document (EN 746-1:1997/prA1:2009) has been prepared by Technical Committee CEN/TC 186
“Industrial thermoprocessing - Safety”, the secretariat of which is held by DIN.
This document is currently submitted to the Unique Acceptance Procedure.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive(s).
For relationship with EU Directive(s), see informative Annexes ZA and ZB, which are integral parts of this
document.
The new safety requirements as stated in this document comply with the additional relevant Essential
Requirements of the new Machinery Directive 2006/42/EC complementing the existing Machinery Directive
98/37/EC.
Once this document is cited in the Official Journal of the European Community under the new Machinery
Directive 2006/42/EC and has been implemented as a national standard in at least one member state, it
confers a presumption of conformity with the new relevant Essential Requirements of that new Directive and
associated EFTA regulations.
This standard forms one part of a series safety standards covering Industrial Thermoprocessing Equipment.
The full list of parts of EN 746 is given below:
EN 746 Industrial thermoprocessing equipment
Part 1: Common safety requirements for industrial thermoprocessing equipment
Part 2: Safety requirements for combustion and fuel handling systems
Part 3: Safety requirements for the generation and use of atmosphere gases
Part 4: Particular safety requirements for hot dip galvanising thermoprocessing equipment
Part 5: Particular Safety Requirements for Salt Bath Thermoprocessing Equipment
Part 6: Particular Safety Requirements for Material Melting, Remelting and Liquid Phase
Maintaining Thermoprocessing Equipment
Part 7: Particular Safety Requirements for Vacuum Thermoprocessing Equipment
Part 8: Particular safety requirements for quenching equipment
EN 1547 Industrial thermoprocessing equipment — Noise test code for industrial thermoprocessing
equipment including its ancillary handling equipment
An assessment of the foreseeable risks arising from the use of the equipment was carried out when this
standard was prepared.
3
---------------------- Page: 5 ----------------------
SIST EN 746-1:2000/kprA1:2009
EN 746-1:1997/prA1:2009 (E)
1 Modification to the Foreword
th
Replace the 7 paragraph with the following:
"For relationship with EU Directive(s), see informative Annexes ZA and ZB, which are integral parts of this
document.".
2 Modification to Clause 2, Normative references
st
Replace the 1 paragraph with the following:
"The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.".
2.1 Basic Standards
In EN 60204-1, replace the bracket expression with "(IEC 60204-1:2005, modified)".
Delete "EN 292-1:1991, Safety of machinery — Basic concepts, general principles for design — Part 1: Basic
terminology, methodology" and add:
"EN ISO 12100-1:2003, Safety of machinery — Basic concepts, general principles for design — Part 1: Basic
terminology, methodology (ISO 12100-1:2003)".
Whole document: Replace "EN 292-1:1991" with "EN ISO 12100-1:2003".
Delete "EN 292-2:1991, Safety of machinery — Basic concepts, general principles for design — Part 2:
Technical principles and specifications" and add:
"EN ISO 12100-2:2003, Safety of machinery — Basic concepts, general principles for design — Part 2:
Technical principles (ISO 12100-2:2003)".
Whole document: Replace "EN 292-2:1991" with "EN ISO 12100-2:2003" where no specific reference has
been made and replace "clause 5 of EN 292-2:1991" in 6.1.2 with "Clause 6 of EN ISO 12100-2:2003" and
delete "Annex A, 1.7.4, f) of EN 292-2:1991" in 6.4.6.
Replace all general references on "EN 292" with "EN ISO 12100".
Replace:
"IEC 364-4-41, Electrical installations of buildings; Part 4: Protection for safety; Chapter 41: Protection against
electrical shock" with:
"IEC 60364-4-41, Low-voltage electrical installations — Part 4-41: Protection for safety — Protection against
electric shock".
Whole document: Replace "IEC 364-4-41" with "IEC 60364-4-41".
Replace:
"IEC 364-4-43, Electrical installations of buildings; Part 4: Protection for safety; Chapter 43: Protection against
overcurrent" with:
"IEC 60364-4-43, Electrical installations of buildings — Part 4-43: Protection for safety — Protection against
overcurrent".
4
---------------------- Page: 6 ----------------------
SIST EN 746-1:2000/kprA1:2009
EN 746-1:1997/prA1:2009 (E)
Whole document: Replace "IEC 364-4-43" with "IEC 60364-4-43".
Delete:
"IEC 364-4-47, Electrical installations of buildings; Part 4: Protection for safety; Chapter 47: Application of
protective measures for safety; Section 470 - General; Section 471 - Measures of protection against electric
shock".
Whole document: Replace "IEC 364-4-47" with "IEC 60364-4-41" or, where "IEC 60364-4-41" is already listed
because of a former change, delete "IEC 364-4-47" (e.g. in Table 1).
Replace:
"IEC 364-4-442, Electrical installations of buildings; Part 4: Protection for safety; Chapter 44: Protection
against overvoltages; Section 442: Protection of low-voltage installations against faults between high-voltage
systems and earth" with:
"IEC 60364-4-44, Low-voltage electrical installations — Part 4-44: Protection for safety — Protection against
voltage disturbances and electromagnetic disturbances".
Whole document: Replace "IEC 364-4-442" with "IEC 60364-4-44".
Delete:
"IEC 364-4-443, Electrical installations of buildings; Part 4: Protection for safety; Chapter 44: Protection
against overvoltages; Section 443: Protection against overvoltages of atmospheric origin or due to switching".
Whole document: Replace "IEC 364-4-443" with "IEC 60364-4-44" or, where "IEC 60364-4-44" is already
listed because of a former change, delete "IEC 364-4-443" (e.g. in Table 1).
Delete:
"IEC 364-4-473, Electrical installations of buildings. Part 4: Protection for safety; Chapter 47: Application of
protective measures for safety. Section 473: Measures of protection
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.