SIST ISO 3547-2:2020

Plain bearings - Wrapped bushes - Part 2: Test data for outside and inside diameters

ISO 3547-2:2017 specifies the test data for outside and inside diameters of wrapped bushes made of mono and multi-layer bearing material for plain bearing applications. It also specifies test designations.
Since the wall thickness of the bush is measured in the free condition, no special test data are required for this on the drawing (see ISO 3547‑5 and ISO 3547‑6).
NOTE Depending on the manufacturing method, the back of the bushes can show isolated light depressions and, similarly, bushes with lubrication holes, grooves and bore indentations can show distortion. It is therefore suggested to measure the wall thickness away from these areas.

Paliers lisses - Bagues roulées

Drsni ležaji - Zvite puše - 2. del: Podatki za preskus zunanjega in notranjega premera

General Information

• Status: Withdrawn
• Publication Date: 19-Jul-2020
• Withdrawal Date: 04-Jun-2024
• ICS: 21.100.10 - Plain bearings
• Technical Committee: ISEL - Mechanical elements
• Current Stage: 9900 - Withdrawal (Adopted Project)
• Start Date: 05-Jun-2024
• Due Date: 28-Jun-2024
• Completion Date: 05-Jun-2024
• Ref Project: ISO 3547-2:2017 - Plain bearings — Wrapped bushes — Part 2: Test data for outside and inside diameters

Relations

• Revised: SIST ISO 3547-2:2008 - Plain bearings - Wrapped bushes - Part 2: Test data for outside and inside diameters
• Effective Date: 19-Dec-2015

Standards Content (Sample)

SLOVENSKI STANDARD
SIST ISO 3547-2:2020
01-oktober-2020
Drsni ležaji - Zvite puše - 2. del: Podatki za preskus zunanjega in notranjega
premera
Plain bearings - Wrapped bushes - Part 2: Test data for outside and inside diameters
Paliers lisses - Bagues roulées
Ta slovenski standard je istoveten z: ISO 3547-2:2017
ICS:
21.100.10 Drsni ležaji Plain bearings
SIST ISO 3547-2:2020 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST ISO 3547-2:2020

---------------------- Page: 2 ----------------------
SIST ISO 3547-2:2020
INTERNATIONAL ISO
STANDARD 3547-2
Third edition
2017-02
Plain bearings — Wrapped bushes —
Part 2:
Test data for outside and inside
diameters
Paliers lisses — Bagues roulées —
Partie 2: Données d’essai pour le diamètre extérieur et le diamètre
intérieur
Reference number
ISO 3547-2:2017(E)
©
ISO 2017

---------------------- Page: 3 ----------------------
SIST ISO 3547-2:2020
ISO 3547-2:2017(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2017, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. [phone]
Fax [phone]
[e-mail]
www.iso.org
ii © ISO 2017 – All rights reserved

---------------------- Page: 4 ----------------------
SIST ISO 3547-2:2020
ISO 3547-2:2017(E)

Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Symbols and units . 2
5 Presentation of data on drawing. 2
6 Tests . 4
6.1 Test A . 4
6.2 Test B . 4
6.3 Test C . 4
6.4 Test D . 4
7 Test A . 4
7.1 Description . 4
7.2 Calculation basis . 4
7.2.1 Elastic reduction, v, of outside diameter, D .
...

INTERNATIONAL ISO
STANDARD 3547-2
Third edition
2017-02
Plain bearings — Wrapped bushes —
Part 2:
Test data for outside and inside
diameters
Paliers lisses — Bagues roulées —
Partie 2: Données d’essai pour le diamètre extérieur et le diamètre
intérieur
Reference number
ISO 3547-2:2017(E)
©
ISO 2017

---------------------- Page: 1 ----------------------
ISO 3547-2:2017(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2017, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. [phone]
Fax [phone]
[e-mail]
www.iso.org
ii © ISO 2017 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 3547-2:2017(E)

Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Symbols and units . 2
5 Presentation of data on drawing. 2
6 Tests . 4
6.1 Test A . 4
6.2 Test B . 4
6.3 Test C . 4
6.4 Test D . 4
7 Test A . 4
7.1 Description . 4
7.2 Calculation basis . 4
7.2.1 Elastic reduction, v, of outside diameter, D .
o 4
7.2.2 Calculation of diameter of checking block, d .
ch, 1 5
7.2.3 Effective cross-sectional area, A .
cal 5
7.2.4 Calculation of checking load, F .
ch 6
7.2.5 Limits for Δz .
...