SIST ISO 3547-2:2008

Plain bearings - Wrapped bushes - Part 2: Test data for outside and inside diameters

The part of ISO 3547 specifies, following ISO 12301, the checking of the inside diameter of wrapped bushes (see ISO 3547-2:2006, method C) and describes the necessary checking methods and measuring equipment. Wrapped bushes in the free condition are flexible, but after insertion they adapt largely to the shape of the housing bore due to the interference between the outside diameter of the bush and the housing bore.

Gleitlager - Gerollte Buchsen - Teil 2: Prüfangaben für Außen- und Innendurchmesser

Paliers lisses - Bagues roulées - Partie 2: Données d'essai pour le diamètre extérieur et le diamètre intérieur

Drsni ležaji - Zvite puše - 2. del: Podatki za preskus zunanjega in notranjega premera

General Information

• Status: Withdrawn
• Publication Date: 11-Jun-2008
• Withdrawal Date: 22-Jun-2020
• ICS: 21.100.10 - Plain bearings
• Technical Committee: ISEL - Mechanical elements
• Current Stage: 9900 - Withdrawal (Adopted Project)
• Start Date: 23-Jun-2020
• Due Date: 16-Jul-2020
• Completion Date: 23-Jun-2020
• Ref Project: ISO 3547-2:2006 - Plain bearings — Wrapped bushes — Part 2: Test data for outside and inside diameters

Relations

• Replaces: SIST ISO 3547-2:2002 - Plain bearings -- Wrapped bushes -- Part 2: Test data for outside and inside diameter
• Effective Date: 01-Jul-2008
• Revised: SIST ISO 3547-2:2020 - Plain bearings - Wrapped bushes - Part 2: Test data for outside and inside diameters
• Effective Date: 19-Dec-2015

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 3547-2
Second edition
2006-10-15

Plain bearings — Wrapped bushes —
Part 2:
Test data for outside and inside
diameters
Paliers lisses — Bagues roulées —
Partie 2: Données d'essai pour le diamètre extérieur et le diamètre
intérieur




Reference number
ISO 3547-2:2006(E)
©
ISO 2006

---------------------- Page: 1 ----------------------
ISO 3547-2:2006(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.


©  ISO 2006
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [e-mail]
Web www.iso.org
Published in Switzerland

ii © ISO 2006 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 3547-2:2006(E)
Contents Page
Foreword. iv
1 Scope .1
2 Normative references .1
3 Terms and definitions .1
4 Symbols and units.2
5 Presentation of data on drawing.2
6 Tests.4
6.1 Test A.4
6.2 Test B .4
6.3 Test C .4
6.4 Test D .4
7 Test A.4
7.1 Description .4
7.2 Calculation basis .4
7.3 Obtaining data — Example .7
7.4 Presentation of data on drawing — Example .8
8 Test B .8
8.1 Description .8
8.2 Obtaining data — Example .9
8.3 Presentation of data on drawing — Example .9
9 Test C .9
9.1 Description .9
9.2 Obtaining data — Example .10
9.3 Presentation of data on drawing — Example .11
10 Test D .11
10.1 Description .11
10.2 Obtaining data — Example .11
10.3 Presentation of data on drawing — Example .12
11 Designation of tests according to this part of ISO 3547.12


© ISO 2006 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO 3547-2:2006(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 3547-2 was prepared by Technical Committee ISO/TC 123, Plain bearings, Subcommittee SC 3,
Dimensions, tolerances and construction details.
This second edition cancels and replaces the first edition (ISO 3547-2:1999), which has been technically
revised.
ISO 3547 consists of the following parts, under the general title Plain bearings — Wrapped bushes:
⎯ Part 1: Dimensions
⎯ Part 2: Test data for outside and inside diameters
⎯ Part 3: Lubrication holes, grooves and indentations
⎯ Part 4: Materials
The following parts are under preparation:
⎯ Part 5: Checking the outside diameter
⎯ Part 6: Checking the inside diameter
⎯ Part 7: Measurement of wall thickness of thin-walled half-bearings and thin-walled bushes

iv © ISO 2006 – All rights reserved

---------------------- Page: 4 ----------------------
INTERNATIONAL STANDARD ISO 3547-2:2006(E)

Plain bearings — Wrapped bushes —
Part 2:
Test data for outside and inside diameters
1 Scope
This part of ISO 3547 specifies the test data for outside and inside diameters of wrapped bushes made of
solid and multi-layer bearing material for plain bearing applications. It also specifies test designations.
Since the wall thickness of the bush is measured in the free condition, no special test data is required for this
on the drawing (see ISO 3547-5 and ISO 3547-6).
NOTE Depending on the manufacturing method, the back of the bushes can show isolated light depressions and,
similarly, bushes with lubrication holes, grooves and bore indentations can show distortion. The wall thickness must
therefore be measured away from these areas.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 3547-1:2006, Plain bearings — Wrapped bushes — Part 1: Dimensions
ISO 3547-4:2006, Plain bearings — Wrapped bushes — Part 4: Materials
ISO 4378-1, Plain bearings — Terms, definitions and classification — Part 1: Design, bearing materials and
their properties
ISO 12301, Plain bearings — Quality control techniques and inspection of geometrical and material quality
characteristics
ISO 13715, Technical drawings — Edges of undefined shape — Vocabulary and indication
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 4378-1 apply.
© ISO 2006 – All rights reserved 1

---------------------- Page: 5 ----------------------
ISO 3547-2:2006(E)
4 Symbols and units
See Table 1.
Table 1 — Symbols and units
Symbol Description Unit
2
A
Reduced area of cross section (calculated value) of the bush mm
cal
B Width of the bush mm
C
Inside chamfer mm
i
C
Outside chamfer mm
o
D
Flange diameter mm
fl
D
Housing bore diameter mm
H
D
Inside diameter of the bush mm
i
D
Inside diameter of the bush in the ring gauge mm
i, ch
D
Outside diameter of the bush mm
o
F
Checking load mm
ch
d
Diameter of the checking block or ring gauge mm
ch, 1
d
Diameter of the setting plug or plug gauge mm
ch, 2
r
Flange radius mm
a
s
mm
Thickness of the backing layer
1
a
s
Thickness of the bearing material layer mm
2
a
s
mm
Wall thickness
3
s
Flange thickness mm
fl
Tolerance of D
∆D
mm
o
o
Elastic reduction of the outside diameter under checking load F
v mm
ch
z Distance apart of the halves of the checking block mm
Indicator reading mm
∆z
∆z
Circumference indicator reading for test D mm
D
a
For bushes which are made of a single material, s = s or s = s .
1 3 2 3

5 Presentation of data on drawing
The drawing should show either
⎯ the outside diameter, D , and the wall thickness, s , or
o 3
⎯ the outside diameter, D , and the inside diameter, D .
o i
Wall thickness, s , and inside diameter, D , shall not be specified together on the same drawing.
3 i
See Figure 1.
2 ©
...

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Plain bearings - Wrapped bushes - Part 2: Test data for outside and inside diametersDrsni ležaji - Zvite puše - 2. del: Podatki za preskus zunanjega in notranjega premeraPaliers lisses - Bagues roulées - Partie 2: Données d'essai pour le diamètre extérieur et le diamètre intérieurGleitlager - Gerollte Buchsen - Teil 2: Prüfangaben für Außen- und Innendurchmesser21.100.10Drsni ležajiPlain bearingsICS:SIST ISO 3547-2:2008enTa slovenski standard je istoveten z:ISO 3547-2:200601-julij-2008SIST ISO 3547-2:2008SLOVENSKI
STANDARDSIST ISO 3547-2:20021DGRPHãþD







Reference numberISO 3547-2:2006(E)© ISO 2006
INTERNATIONAL STANDARD ISO3547-2Second edition2006-10-15Plain bearings — Wrapped bushes — Part 2: Test data for outside and inside diameters Paliers lisses — Bagues roulées — Partie 2: Données d'essai pour le diamètre extérieur et le diamètre intérieur



ISO 3547-2:2006(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
©
ISO 2006 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body in the country of the requester. ISO copyright office Case postale 56 • CH-1211 Geneva 20 Tel.
+ 41 22 749 01 11 Fax
+ 41 22 749 09 47 E-mail
[e-mail] Web
www.iso.org Published in Switzerland
ii © ISO 2006 – All rights reserved



ISO 3547-2:2006(E) © ISO 2006 – All rights reserved iiiContents Page Foreword.iv 1 Scope.1 2 Normative references.1 3 Terms and definitions.1 4 Symbols and units.2 5 Presentation of data on drawing.2 6 Tests.4 6.1 Test A.4 6.2 Test B.4 6.3 Test C.4 6.4 Test D.4 7 Test A.4 7.1 Description.4 7.2 Calculation basis.4 7.3 Obtaining data — Example.7 7.4 Presentation of data on drawing — Example.8 8 Test B.8 8.1 Description.8 8.2 Obtaining data — Example.9 8.3 Presentation of data on drawing — Example.9 9 Test C.9 9.1 Description.9 9.2 Obtaining data — Example.10 9.3 Presentation of data on drawing — Example.11 10 Test D.11 10.1 Description.11 10.2 Obtaining data — Example.11 10.3 Presentation of data on drawing — Example.12 11 Designation of tests according to this part of ISO 3547.12



ISO 3547-2:2006(E) iv © ISO 2006 – All rights reserved Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 3547-2 was prepared by Technical Committee ISO/TC 123, Plain bearings, Subcommittee SC 3, Dimensions, tolerances and construction details. This second edition cancels and replaces the first edition (ISO 3547-2:1999), which has been technically revised. ISO 3547 consists of the following parts, under the general title Plain bearings — Wrapped bushes: ⎯ Part 1: Dimensions ⎯ Part 2: Test data for outside and inside diameters ⎯ Part 3: Lubrication holes, grooves and indentations ⎯ Part 4: Materials The following parts are under preparation: ⎯ Part 5: Checking the outside diameter ⎯ Part 6: Checking the inside diameter ⎯ Part 7: Measurement of wall thickness of thin-walled half-bearings and thin-walled bushes



INTERNATIONAL STANDARD ISO 3547-2:2006(E) © ISO 2006 – All rights reserved 1Plain bearings — Wrapped bushes — Part 2: Test data for outside and inside diameters 1 Scope This part of ISO 3547 specifies the test data for outside and inside diameters of wrapped bushes made of solid and multi-layer bearing material for plain bearing applications. It also specifies test designations. Since the wall thickness of the bush is measured in the free condition, no special test data is required for this on the drawing (see ISO 3547-5 and ISO 3547-6). NOTE Depending on the manufacturing method, the back of the bushes can show isolated light depressions and, similarly, bushes with lubrication holes, grooves and bore indentations can show distortion. The wall thickness must therefore be measured away from these areas. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 3547-1:2006, Plain bearings — Wrapped bushes — Part 1: Dimensions ISO 3547-4:2006, Plain bearings — Wrapped bushes — Part 4: Materials ISO 4378-1, Plain bearings — Terms, definitions and classification — Part 1: Design, bearing materials and their properties ISO 12301, Plain bearings — Quality control techniques and inspection of geometrical and material quality characteristics ISO 13715, Technical drawings — Edges of undefined shape — Vocabulary and indication 3 Terms and definitions For the purposes of this document, the terms and definitions given in ISO 4378-1 apply.



ISO 3547-2:2006(E) 2 © ISO 2006 – All rights reserved 4 Symbols and units See Table 1. Table 1 — Symbols and units Symbol Description Unit Acal Reduced area of cross section (calculated value) of the bush mm2 B Width of the bush mm Ci Inside chamfer mm Co Outside chamfer mm Dfl Flange diameter mm DH Housing bore diameter mm Di Inside diameter of the bush mm Di, ch Inside diameter of the bush in the ring gauge mm Do Outside diameter of the bush mm Fch Checking load mm dch, 1 Diameter of the checking block or ring gauge mm dch, 2 Diame
...