SIST EN 60917-2-5:2013

Modular order for the development of mechanical structures for electronic equipment practices - Part 2-5: Sectional specification - Interface coordination dimensions for the 25 mm equipment practice - Cabinet interface dimensions for miscellaneous equipment

This part of the IEC 60917 series applies to a frame-based cabinet structure with the specification of interface dimensions for the installation of miscellaneous equipment. The frame structure provides the mounting planes with mounting points for the assembly of internal and external accessories. Unlike the existing standards IEC 60917-2-1 and IEC 60297-3-100, this standard allows cover parts like top covers and front/rear doors to exceed the cabinet's external coordination dimensions.

Modulordnung für die Entwicklung von Bauweisen für elektronische Einrichtungen - Teil 2-5: Strukturnorm – Schnittstellen-Koordinationsmaße für die 25-mm-Bauweise – Schrank-Schnittstellenmaße für sonstige Einrichtungen

Ordre modulaire pour le développement des structures mécaniques pour les infrastructures électroniques - Partie 2-5: Spécification intermédiaire - Dimensions de coordination pour les interfaces des infrastructures au pas de 25 mm - Dimensions pour les interfaces des baies pour équipements divers

La CEI 60917-2-5:2012 s'applique à une structure de baie utilisant des cadres avec spécification des dimensions pour les interfaces en vue de l'installation des équipements divers. La structure utilisant des cadres fournit des plans de montage avec des points de montage pour l'assemblage des accessoires intérieurs et extérieurs. A la différence des normes existantes CEI 60917-2-1 et CEI 60297-3-100, la présente norme autorise que les parties servant de couvercles comme les couvercles supérieurs et que les portes avant/arrière dépassent les dimensions de coordination extérieures de la baie. Mots clé: cadre modulaire, montage de cadre, structure de baie

Razpored modulov za razvoj mehanske zgradbe elektronske opreme - 2-5. del: Področna specifikacija - Usklajevalne mere vmesnika za 25-milimetrsko elektronsko opremo - Mere vmesnika omarice za različno opremo

Ta del skupine standardov IEC 60917 se uporablja za zgradbo omarice, ki temelji na okvirju, in zajema specifikacijo mer vmesnika za namestitev različne opreme. Zgradba okvira zagotavlja pritrditvene ploskve s pritrditvenimi točkami za sestavljanje notranjih in zunanjih priključkov. Ta standard v nasprotju z obstoječima standardoma IEC 60917-2-1 in IEC 60297-3-100 dovoljuje, da pokrivni deli, kot so vrhnji pokrovi in vrata na sprednji/zadnji strani, presegajo zunanje usklajevalne mere omarice.

General Information

• Status: Published
• Publication Date: 04-Feb-2013
• ICS: 31.240 - Mechanical structures for electronic equipment
• Technical Committee: I11 - Imaginarni 11
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 01-Feb-2013
• Due Date: 08-Apr-2013
• Completion Date: 05-Feb-2013
• Ref Project: EN 60917-2-5:2012 - Modular order for the development of mechanical structures for electronic equipment practices - Part 2-5: Sectional specification - Interface co-ordination dimensions for the 25 mm equipment practice - Cabinet interface dimensions for miscellaneous equipment

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 60917-2-5:2013
01-marec-2013
5D]SRUHGPRGXORY]DUD]YRMPHKDQVNH]JUDGEHHOHNWURQVNHRSUHPHGHO
3RGURþQDVSHFLILNDFLMD8VNODMHYDOQHPHUHYPHVQLND]DPLOLPHWUVNR
HOHNWURQVNRRSUHPR0HUHYPHVQLNDRPDULFH]DUD]OLþQRRSUHPR
Modular order for the development of mechanical structures for electronic equipment
practices - Part 2-5: Sectional specification - Interface coordination dimensions for the 25
mm equipment practice - Cabinet interface dimensions for miscellaneous equipment
Modulordnung für die Entwicklung von Bauweisen für elektronische Einrichtungen - Teil
2-5: Strukturnorm – Schnittstellen-Koordinationsmaße für die 25-mm-Bauweise –
Schrank-Schnittstellenmaße für sonstige Einrichtungen
Ordre modulaire pour le développement des structures mécaniques pour les
infrastructures électroniques - Partie 2-5: Spécification intermédiaire - Dimensions de
coordination pour les interfaces des infrastructures au pas de 25 mm - Dimensions pour
les interfaces des baies pour équipements divers
Ta slovenski standard je istoveten z: EN 60917-2-5:2012
ICS:
31.240 Mehanske konstrukcije za Mechanical structures for
elektronsko opremo electronic equipment
SIST EN 60917-2-5:2013 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 60917-2-5:2013

---------------------- Page: 2 ----------------------

SIST EN 60917-2-5:2013

EUROPEAN STANDARD
EN 60917-2-5

NORME EUROPÉENNE
October 2012
EUROPÄISCHE NORM

ICS 31.240

English version

Modular order for the development of mechanical structures for electronic
equipment practices -
Part 2-5: Sectional specification -
Interface co-ordination dimensions for the 25 mm equipment practice -
Cabinet interface dimensions for miscellaneous equipment
(IEC 60917-2-5:2012)

Ordre modulaire pour le développement Modulordnung für die Entwicklung von
des structures mécaniques pour les Bauweisen für elektronische
infrastructures électroniques - Einrichtungen -
Partie 2-5: Spécification intermédiaire - Teil 2-5: Strukturnorm -
Dimensions de coordination pour les Schnittstellen-Koordinationsmaße für die
interfaces des infrastructures au pas de 25-mm-Bauweise -
25 mm - Schrank-Schnittstellenmaße für sonstige
Dimensions pour les interfaces des baies Einrichtungen
pour équipements divers (IEC 60917-2-5:2012)
(CEI 60917-2-5:2012)



This European Standard was approved by CENELEC on 2012-08-28. CENELEC members are bound to comply
with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the CEN-CENELEC Management Centre or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and notified
to the CEN-CENELEC Management Centre has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus,
the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany,
Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.

CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

Management Centre: Avenue Marnix 17, B - 1000 Brussels


© 2012 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 60917-2-5:2012 E

---------------------- Page: 3 ----------------------

SIST EN 60917-2-5:2013
EN 60917-2-5:2012 - 2 -

Foreword
The text of document 48D/509/FDIS, future edition 1 of IEC 60917-2-5, prepared by SC 48D, "Mechanical
structures for electronic equipment", of IEC TC 48, "Electromechanical components and mechanical
structures for electronic equipment" was submitted to the IEC-CENELEC parallel vote and approved by
CENELEC as EN 60917-2-5:2012.

The following dates are fixed:
(dop) 2013-05-28
• latest date by which the document has
to be implemented at national level by
publication of an identical national
standard or by endorsement
(dow) 2015-08-28
• latest date by which the national
standards conflicting with the
document have to be withdrawn

Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such patent
rights.

Endorsement notice
The text of the International Standard IEC 60917-2-5:2012 was approved by CENELEC as a European
Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards indicated:
IEC 60297 series NOTE  Harmonized in EN 60297 series.
IEC 60917 series NOTE  Harmonized in EN 60917 series.

---------------------- Page: 4 ----------------------

SIST EN 60917-2-5:2013
- 3 - EN 60917-2-5:2012

Annex ZA
(normative)

Normative references to international publications
with their corresponding European publications

The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.

NOTE  When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD
applies.

Publication Year Title EN/HD Year

IEC 60297-3-100 - Mechanical structures for electronic EN 60297-3-100 -
equipment - Dimensions of mechanical
structures of the 482,6 mm (19 in) series -
Part 3-100: Basic dimensions of front panels,
subracks, chassis, racks and cabinets


IEC 60917-1 - Modular order for the development of EN 60917-1 -
mechanical structures for electronic
equipment practices -
Part 1: Generic standard


IEC 60917-2-1 - Modular order for the development of EN 60917-2-1 -
mechanical structures for electronic
equipment practices -
Part 2: Sectional specification - Interface
co-ordination dimensions for the 25 mm
equipment practice -
Section 1: Detail specification - Dimensions
for cabinets and racks

---------------------- Page: 5 ----------------------

SIST EN 60917-2-5:2013

---------------------- Page: 6 ----------------------

SIST EN 60917-2-5:2013




IEC 60917-2-5

®


Edition 1.0 2012-07




INTERNATIONAL



STANDARD




NORME



INTERNATIONALE
colour

inside










Modular order for the development of mechanical structures for electronic

equipment practices –

Part 2-5: Sectional specification – Interface co-ordination dimensions for the


25 mm equipment practice – Cabinet interface dimensions for miscellaneous

equipment




Ordre modulaire pour le développement des structures mécaniques pour les

infrastructures électroniques –

Partie 2-5: Spécification intermédiaire – Dimensions de coordination pour les

interfaces des infrastructures au pas de 25 mm – Dimensions pour les

interfaces des baies pour équipements divers








INTERNATIONAL

ELECTROTECHNICAL

COMMISSION


COMMISSION

ELECTROTECHNIQUE

PRICE CODE
INTERNATIONALE

CODE PRIX R


ICS 31.240 ISBN 978-2-83220-152-7



Warning! Make sure that you obtained this publication from an authorized distributor.

Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé.

® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale

---------------------- Page: 7 ----------------------

SIST EN 60917-2-5:2013
– 2 – 60917-2-5 © IEC:2012
CONTENTS
FOREWORD . 3
INTRODUCTION . 5
1 Scope . 6
2 Normative references . 6
3 Terms and definitions . 7
4 Arrangement overview of a frame based cabinet structure . 8
5 External coordination dimensions of a cabinet . 9
5.1 General . 9
5.2 Cabinet frame mounting points . 9
6 Modular frame type cabinet structure . 11
6.1 General . 11
6.2 Modular frame type “M” . 11
6.3 Modular frame type “N” . 13
Annex A (informative) Illustrative figures . 15
Bibliography . 19

Figure 1 – Arrangement overview of a frame based cabinet structure . 8
Figure 2 – External coordination dimensions of cabinet . 9
Figure 3 – Frame mounting points of a modular cabinet . 10
Figure 4 – Modular frame type “M“ 600 mm × 600 mm . 12
Figure 5 – Modular frame type “N” 600 mm × 600 mm . 13
Figure A.1 – Illustrative figures for coordination dimensions of cabinet . 15
Figure A.2 – Examples of arrangements of miscellaneous equipment . 16
Figure A.3 – Cabinet mounting uprights mounted on “M” type frame 600 mm × 600 mm . 17
Figure A.4 – Cabinet mounting uprights mounted on “N” type frame 600 mm × 600 mm . 18

Table 1 – External coordination dimensions of cabinet . 14

---------------------- Page: 8 ----------------------

SIST EN 60917-2-5:2013
60917-2-5 © IEC:2012 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________

MODULAR ORDER FOR THE DEVELOPMENT OF MECHANICAL
STRUCTURES FOR ELECTRONIC EQUIPMENT PRACTICES –

Part 2-5: Sectional specification –
Interface co-ordination dimensions for the 25 mm equipment practice –
Cabinet interface dimensions for miscellaneous equipment


FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 60917-2-5 has been prepared by subcommittee 48D: Mechanical
structures for electronic equipment, of IEC technical committee 48: Electromechanical
components and mechanical structures for electronic equipment.
The text of this standard is based on the following documents:
FDIS Report on voting
48D/509/FDIS 48D/516/RVD

Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.

---------------------- Page: 9 ----------------------

SIST EN 60917-2-5:2013
– 4 – 60917-2-5 © IEC:2012
A list of all the parts in the IEC 60917 series, published under the general title Modular order
for the development of mechanical structures for electronic equipment practices can be found
on the IEC website.
The committee has decided that the contents of this publication will remain unchanged until
the stability date indicated on the IEC web site under "http://webstore.iec.ch" in the data
related to the specific publication. At this date, the publication w
...