SIST EN ISO 13433:2007

Geosynthetics - Dynamic perforation test (cone drop test) (ISO 13433:2006)

This International Standard specifies a method to determine the resistance of geosynthetics to penetration by a steel cone dropped from a fixed height. The degree of penetration is an indication of the behaviour of the geosynthetic when sharp stones are dropped on its surface. The method is generally applicable to geosynthetics. However, the validity of this test for so me types of products should be considered carefully, as the test principle may not be applicable.

Geokunststoffe - Dynamischer Durchschlagversuch (Kegelfallversuch) (ISO 13433:2006)

Diese Internationale Norm legt ein Verfahren zur Bestimmung des Widerstandes von Geokunststoffen gegen das Durchdringen eines Stahlkegels fest, der aus einer bestimmten Höhe fallen gelassen wird.
Der Grad der Durchdringung ist ein Hinweis auf das Verhalten des Geokunststoffes, wenn scharfkantige Steine auf seine Oberfläche fallen gelassen werden.
Das Verfahren ist allgemein auf Geokunststoffe anwendbar. Die Gültigkeit dieser Prüfung sollte jedoch bei einigen Produktarten sorgfältig geprüft werden, weil die Prüfungsbeschreibung nicht anwendbar zu sein braucht.

Géosynthétiques - Essai de perforation dynamique (essai par chute d'un cône) (ISO 13433:2006)

L'ISO 13433:2006 spécifie une méthode de détermination de la résistance de géosynthétiques à la pénétration par un cône d'acier tombant en chute libre d'une hauteur déterminée. Le degré de pénétration constitue une indication sur le comportement du géosynthétique lors de la chute de pierres anguleuses sur sa surface.
La méthode est généralement applicable à tous les géosynthétiques. Pour certains types de produits, il convient de considérer la validité de l'essai avec prudence, car le principe de l'essai peut ne pas être applicable.

Geosintetika - Dinamični luknjalni preskus (preskus s padanjem stožca) (ISO 13433:2006)

General Information

• Status: Published
• Publication Date: 31-Dec-2006
• ICS: 59.080.70 - Geotextiles
• Technical Committee: ITEK - Textile and textile products
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 01-Jan-2007
• Due Date: 01-Jan-2007
• Completion Date: 01-Jan-2007
• Directive: 89/106/EEC - Construction products
• Mandate: M/107 - Mandate to CEN/CENELEC concerning the execution of standardization work for harmonized standards on geotextiles
• Ref Project: EN ISO 13433:2006 - Geosynthetics - Dynamic perforation test (cone drop test) (ISO 13433:2006)

Relations

• Replaces: SIST EN 918:1999 - Geotextiles and geotextile-related products - Dynamic perforation test (cone drop test)
• Effective Date: 01-Jan-2007

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 13433:2007
01-januar-2007
1DGRPHãþD
SIST EN 918:1999
*HRVLQWHWLND'LQDPLþQLOXNQMDOQLSUHVNXVSUHVNXVVSDGDQMHPVWRåFD,62

Geosynthetics - Dynamic perforation test (cone drop test) (ISO 13433:2006)
Geokunststoffe - Dynamischer Durchschlagversuch (Kegelfallversuch) (ISO 13433:2006)
Géosynthétiques - Essai de perforation dynamique (essai par chute d'un cône) (ISO
13433:2006)
Ta slovenski standard je istoveten z: EN ISO 13433:2006
ICS:
59.080.70 Geotekstilije Geotextiles
SIST EN ISO 13433:2007 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

EUROPEAN STANDARD
EN ISO 13433
NORME EUROPÉENNE
EUROPÄISCHE NORM
August 2006
ICS 59.080.70 Supersedes EN 918:1995
English Version
Geosynthetics - Dynamic perforation test (cone drop test) (ISO
13433:2006)
Géosynthétiques - Essai de perforation dynamique (essai Geokunststoffe - Dynamischer Durchschlagversuch
par chute d'un cône) (ISO 13433:2006) (Kegelfallversuch) (ISO 13433:2006)
This European Standard was approved by CEN on 1 July 2006.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Central Secretariat or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,
Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2006 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 13433:2006: E
worldwide for CEN national Members.

---------------------- Page: 2 ----------------------

EN ISO 13433:2006 (E)





Foreword


This document (EN ISO 13433:2006) has been prepared by Technical Committee CEN/TC 189
"Geosynthetics", the secretariat of which is held by IBN, in collaboration with Technical
Committee ISO/TC 221 "Geosynthetics".

This European Standard shall be given the status of a national standard, either by publication of
an identical text or by endorsement, at the latest by February 2007, and conflicting national
standards shall be withdrawn at the latest by February 2007.

This document supersedes EN 918:1995.

According to the CEN/CENELEC Internal Regulations, the national standards organizations of
the following countries are bound to implement this European Standard: Austria, Belgium,
Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary,
Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.


2

---------------------- Page: 3 ----------------------

INTERNATIONAL ISO
STANDARD 13433
First edition
2006-08-01

Geosynthetics — Dynamic perforation
test (cone drop test)
Géosynthétiques — Essai de perforation dynamique (essai par chute
d'un cône)




Reference number
ISO 13433:2006(E)
©
ISO 2006

---------------------- Page: 4 ----------------------

ISO 13433:2006(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.


©  ISO 2006
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [e-mail]
Web www.iso.org
Published in Switzerland

ii © ISO 2006 – All rights reserved

---------------------- Page: 5 ----------------------

ISO 13433:2006(E)
Contents Page
Foreword. iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions. 1
4 Principle. 1
5 Apparatus . 2
6 Specimens . 5
6.1 Sampling. 5
6.2 Number and dimension of specimens. 5
7 Conditioning. 6
8 Procedure . 6
9 Calculation. 6
10 Test report . 6

© ISO 2006 – All rights reserved iii

---------------------- Page: 6 ----------------------

ISO 13433:2006(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
Internationa
...