Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-35: Tests - Cable nutation (IEC 61300-2-35:2014)

This part of IEC 61300 details procedures for determining the suitability of a fibre optic device
to withstand nutation that may occur during operation, service, storage and/or transport. The
test is intended to indicate the performance of such devices when exposed to torsion and
bending as a combined load.

Lichtwellenleiter - Verbindungselemente und passive Bauteile - Grundlegende Prüf- und Messverfahren - Teil 2-35: Prüfungen - Kabelnutation (IEC 61300-2-35:2014)

Dispositifs d'interconnexion et composants passifs à fibres optiques - Procédures fondamentales d'essais et de mesures - Partie 2-35: Essais - Nutation du câble (CEI 61300-2-35:2014)

L'IEC 61300-2-35:2014 décrit des méthodes destinées à déterminer l'aptitude d'un dispositif à fibres optiques à supporter une nutation qui peut intervenir en cours du fonctionnement, de l'entretien, du stockage et/ou du transport. L'essai est destiné à indiquer la performance de tels dispositifs lorsqu'ils sont exposés à une charge combinée de torsion et de courbure. Cette deuxième édition annule et remplace la première édition, parue en 1995, dont elle constitue une révision technique. Cette édition inclut les modifications techniques significatives suivantes par rapport à l'édition précédente:  - ajout de nouvelles références normatives;  - ajout de nouveaux termes et définitions;  - ajout de deux figures relatives aux appareillages d'essai: l'une comportant un DUT en rotation horizontale, l'autre comportant une unité de déflexion en rotation;  - réexamen de la sévérité. Mots clés: nutation, dispositif à fibres optiques

Optični spojni elementi in pasivne komponente - Osnovni preskusni in merilni postopki - 2-35. del: Preskušanje - Nutacija kabla (IEC 61300-2-35:2014)

V tem delu standarda IEC 61300 so podrobno opisani postopki za ugotavljanje primernosti naprav z optičnimi vlakni za odpornost proti nutaciji, ki se lahko pojavi med delovanjem, servisiranjem, shranjevanjem in/ali prevozom. Preskus je namenjen določanju učinkovitosti takih naprav, kadar so te izpostavljene torziji in zvijanju kot skupni obremenitvi.

General Information

Status
Published
Publication Date
26-Feb-2015
Technical Committee
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
09-Jan-2015
Due Date
16-Mar-2015
Completion Date
27-Feb-2015

Relations

Buy Standard

Standard
EN 61300-2-35:2015 - BARVE
English language
16 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 61300-2-35:2015
01-april-2015
2SWLþQLVSRMQLHOHPHQWLLQSDVLYQHNRPSRQHQWH2VQRYQLSUHVNXVQLLQPHULOQL
SRVWRSNLGHO3UHVNXãDQMH1XWDFLMDNDEOD ,(&
Fibre optic interconnecting devices and passive components - Basic test and
measurement procedures - Part 2-35: Tests - Cable nutation (IEC 61300-2-35:2014)
Lichtwellenleiter - Verbindungselemente und passive Bauteile - Grundlegende Prüf- und
Messverfahren - Teil 2-35: Prüfungen - Kabelnutation (IEC 61300-2-35:2014)
Dispositifs d'interconnexion et composants passifs à fibres optiques - Procédures
fondamentales d'essais et de mesures - Partie 2-35: Essais - Nutation du câble (CEI
61300-2-35:2014)
Ta slovenski standard je istoveten z: EN 61300-2-35:2014
ICS:
33.180.20 3RYH]RYDOQHQDSUDYH]D Fibre optic interconnecting
RSWLþQDYODNQD devices
SIST EN 61300-2-35:2015 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 61300-2-35:2015

---------------------- Page: 2 ----------------------

SIST EN 61300-2-35:2015


EUROPEAN STANDARD EN 61300-2-35

NORME EUROPÉENNE

EUROPÄISCHE NORM
July 2014
ICS 33.180.20 Supersedes EN 61300-2-35:1997
English Version
Fibre optic interconnecting devices and passive components -
Basic test and measurement procedures - Part 2-35: Tests -
Cable nutation
(IEC 61300-2-35:2014)
Dispositifs d'interconnexion et composants passifs à fibres Lichtwellenleiter - Verbindungselemente und passive
optiques - Procédures fondamentales d'essais et de Bauteile - Grundlegende Prüf- und Messverfahren - Teil 2-
mesures - Partie 2-35: Essais - Nutation du câble 35: Prüfungen - Kabelnutation
(CEI 61300-2-35:2014) (IEC 61300-2-35:2014)
This European Standard was approved by CENELEC on 2014-04-11. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.



European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2014 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
 Ref. No. EN 61300-2-35:2014 E

---------------------- Page: 3 ----------------------

SIST EN 61300-2-35:2015
EN 61300-2-35:2014 - 2 -
Foreword
The text of document 86B/3703/FDIS, future edition 2 of IEC 61300-2-35, prepared by SC 86B "Fibre
optic interconnecting devices and passive components" of IEC/TC 86 "Fibre optics" was submitted to
the IEC-CENELEC parallel vote and approved by CENELEC as EN 61300-2-35:2014.
The following dates are fixed:
– latest date by which the document has to be implemented at (dop) 2015-01-11
national level by publication of an identical national
standard or by endorsement
– latest date by which the national standards conflicting with (dow) 2015-04-11
the document have to be withdrawn

Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such
patent rights.
This document supersedes EN 61300-2-35:1997.
Endorsement notice
The text of the International Standard IEC 61300-2-35:2014 was approved by CENELEC as a
European Standard without any modification.
In the official version, for Bibliography, the following note has to be added for the standard indicated:
IEC 61753-1 NOTE  Harmonized as EN 61753-1.

---------------------- Page: 4 ----------------------

SIST EN 61300-2-35:2015
- 3 - EN 61300-2-35:2014

Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
NOTE 1 When an International Publication has been modified by common modifications, indicated by (mod), the relevant
EN/HD applies.

NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available here:
www.cenelec.eu.
Publication Year Title EN/HD Year
IEC 61300-3-1 -  Fibre optic interconnecting devices and EN 61300-3-1 -
passive components - Basic test and
measurement procedures -- Part 3-1:
Examinations and measurements - Visual
examination
IEC 61300-3-3 -  Fibre optic interconnecting devices and EN 61300-3-3 -
passive components - Basic test and
measurement procedures -- Part 3-3:
Examinations and measurements - Active
monitoring of changes in attenuation and
return loss
IEC 61300-3-4 -  Fibre optic interconnecting devices and EN 61300-3-4 -
passive components - Basic test and
measurement procedures -- Part 3-4:
Examinations and measurements -
Attenuation

---------------------- Page: 5 ----------------------

SIST EN 61300-2-35:2015

---------------------- Page: 6 ----------------------

SIST EN 61300-2-35:2015




IEC 61300-2-35

®


Edition 2.0 2014-03




INTERNATIONAL



STANDARD




NORME



INTERNATIONALE
colour

inside










Fibre optic interconnecting devices and passive components – Basic test and

measurement procedures –

Part 2-35: Tests – Cable nutation




Dispositifs d’interconnexion et composants passifs à fibres optiques –

Procédures fondamentales d’essais et de mesures –


Partie 2-35: Essais – Nutation du câble













INTERNATIONAL

ELECTROTECHNICAL

COMMISSION


COMMISSION

ELECTROTECHNIQUE

PRICE CODE
INTERNATIONALE

CODE PRIX M


ICS 33.180.20 ISBN 978-2-8322-1395-7



Warning! Make sure that you obtained this publication from an authorized distributor.

Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé.

® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale

---------------------- Page: 7 ----------------------

SIST EN 61300-2-35:2015
– 2 – IEC 61300-2-35:2014 © IEC 2014
CONTENTS

FOREWORD . 3
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 General description . 6
5 Apparatus . 6
5.1 Design of the apparatus . 6
5.2 Optical measurements . 9
6 Procedure . 9
6.1 Preconditioning . 9
6.2 Initial examinations and measurements . 9
6.3 Conditioning . 10
6.4 Recovery . 10
6.5 Final examinations and measurements . 10
7 Severity . 10
8 Details to be specified . 11
Annex A (informative) Example for a test set-up . 12
Bibliography . 13

Figure 1 – Test apparatus with vertical rotating DUT . 7
Figure 2 – Test apparatus with horizontal rotating DUT . 8
Figure 3 – Test apparatus with rotating deflection unit . 9
Figure A.1 – Example for a test set-up . 12

Table 1 – Severities . 10

---------------------- Page: 8 ----------------------

SIST EN 61300-2-35:2015
IEC 61300-2-35:2014 © IEC 2014 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________

FIBRE OPTIC INTERCONNECTING
DEVICES AND PASSIVE COMPONENTS –
BASIC TEST AND MEASUREMENT PROCEDURES –

Part 2-35: Tests – Cable nutation


FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.