SIST EN 10216-2:2003/oprA2:2007
(Main)Seamless steel tubes for pressure purposes - Technical delivery conditions - Part 2: Non-alloy and alloy steel tubes with specified elevated temperature properties
Seamless steel tubes for pressure purposes - Technical delivery conditions - Part 2: Non-alloy and alloy steel tubes with specified elevated temperature properties
Inclusion of new steel grades not considered during the preparation of the EN issued on 2002
Nahtlose Stahlrohre für Druckbeanspruchungen - Technische Lieferbedingungen - Teil 2: Rohre aus unlegierten und legierten Stählen mit festgelegten Eigenschaften bei erhöhten Temperaturen
Tubes sans soudure en acier pour service sous pression - Conditions techniques de livraison - Partie 2: Tubes en acier non allié et allié avec caractéristiques spécifiées a température élevée
Nevarjene jeklene cevi za tlačne posode - Tehnični dobavni pogoji - 2. del: Nelegirane in legirane jeklene cevi s specificiranimi lastnostmi za delo pri povišanih temperaturah
General Information
Relations
Standards Content (Sample)
SLOVENSKI SIST EN 10216-
2:2003/oprA2:2005
PREDSTANDARD
maj 2005
Nevarjene jeklene cevi za tlačne posode - Tehnični dobavni pogoji - 2. del:
Nelegirane in legirane jeklene cevi s specificiranimi lastnostmi za delo pri
povišanih temperaturah
Seamless steel tubes for pressure purposes - Technical delivery conditions - Part 2:
Non-alloy and alloy steel tubes with specified elevated temperature properties
ICS 23.040.10; 77.140.75 Referenčna številka
SIST EN 10216-2:2003/oprA2:2005(en)
© Standard je založil in izdal Slovenski inštitut za standardizacijo. Razmnoževanje ali kopiranje celote ali delov tega dokumenta ni dovoljeno
---------------------- Page: 1 ----------------------
EUROPEAN STANDARD
DRAFT
EN 10216-2:2002
NORME EUROPÉENNE
EUROPÄISCHE NORM
prA2
March 2005
ICS
English version
Seamless steel tubes for pressure purposes - Technical delivery
conditions - Part 2: Non-alloy and alloy steel tubes with specified
elevated temperature properties
Tubes sans soudure en acier pour service sous pression - Nahtlose Stahlrohre für Druckbeanspruchungen -
Conditions techniques de livraison - Partie 2 : Tubes en Technische Lieferbedingungen - Teil 2: Rohre aus
acier non allié et allié avec caractéristiques spécifiées à unlegierten und legierten Stählen mit festgelegten
température élevée Eigenschaften bei erhöhten Temperaturen
This draft amendment is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee ECISS/TC 29.
This draft amendment A2, if approved, will modify the European Standard EN 10216-2:2002. If this draft becomes an amendment, CEN
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this amendment
into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other language made
by translation under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status
as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2005 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 10216-2:2002/prA2:2005: E
worldwide for CEN national Members.
---------------------- Page: 2 ----------------------
EN 10216-2:2002/prA2:2005 (E)
Contents
Foreword .3
7.3 Tube manufacture and delivery condition .4
8.2 Chemical composition .5
8.3 Mechanical properties.9
9.3 Summary of inspection and testing.13
11.3 Flattening test .14
11.5 Drift expanding test.15
Annex A (Informative) .16
Creep rupture strength values .16
Annex ZA (informative) .22
Relationship between this European Standard and the Essential Requirements of EU Directive 97/23/EC.22
2
---------------------- Page: 3 ----------------------
EN 10216-2:2002/prA2:2005 (E)
Foreword
This document (EN 10216-2:2002/prA2:2005) has been prepared by Technical Committee ECISS/TC 29 “Steel
tubes and fittings for steel tubes”, the secretariat of wh
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.