SIST EN 14187-9:2006
(Main)Cold applied joint sealants - Test methods - Part 9: Function testing of joint sealants
Cold applied joint sealants - Test methods - Part 9: Function testing of joint sealants
This European Standard specifies a function test for cold applied joint sealants intended for use in joints in roads and airfield pavements in cold climate areas where the total joint movement can be greater than 35 % and the temperature can go below -25 °C.
Kalt verarbeitbare Fugenmassen - Prüfverfahren - Teil 9: Funktionsprüfung von Fugenmassen
Diese Europäische Norm legt eine Funktionsprüfung für kalt verarbeitbare Fugenmassen fest, die für die Anwendung in Arbeitsfugen und in ohne Fremdeinwirkung entstandenen Rissen in Fahrbahnbefestigungen und Flugplatzdecken vorgesehen sind.
Mastics pour joints appliqués a froid - Méthodes d'essai - Partie 9 : Fonctionnalité des mastics pour joints
Hladno nanosljive tesnilne mase za stike – 9. del: Preskušanje funkcionalnosti tesnilnih mas za stike
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Hladno nanosljive tesnilne mase za stike – 9. del: Preskušanje funkcionalnosti tesnilnih mas za stikeKalt verarbeitbare Fugenmassen - Prüfverfahren - Teil 9: Funktionsprüfung von FugenmassenMastics pour joints appliqués a froid - Méthodes d'essai - Partie 9 : Fonctionnalité des mastics pour jointsCold applied joint sealants - Test methods - Part 9: Function testing of joint sealants93.080.20Materiali za gradnjo cestRoad construction materials91.100.50Veziva. Tesnilni materialiBinders. Sealing materialsICS:Ta slovenski standard je istoveten z:EN 14187-9:2006SIST EN 14187-9:2006en01-april-2006SIST EN 14187-9:2006SLOVENSKI
STANDARD
SIST EN 14187-9:2006
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 14187-9February 2006ICS 93.080.20 English VersionCold applied joint sealants - Test methods - Part 9: Functiontesting of joint sealantsMastics pour joints appliqués à froid - Méthodes d'essai -Partie 9 : Fonctionnalité des mastics pour jointsKalt verarbeitbare Fugenmassen - Prüfverfahren - Teil 9:Funktionsprüfung von FugenmassenThis European Standard was approved by CEN on 30 December 2005.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2006 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 14187-9:2006: ESIST EN 14187-9:2006
EN 14187-9:2006 (E) 2 Contents Page Foreword.3 1 Scope.4 2 Normative references.4 3 Terms and definitions.4 4 Principle.4 5 Apparatus and materials.4 5.1 Concrete test blocks.4 5.2 Tensile/compression test rig.4 5.3 Climate chamber.5 5.4 Temperature indicator.5 6 Preparation of the test specimens.5 7 Procedure.6 7.1 Conditioning cycle.6 7.2 After conditioning.8 7.3 Test procedure.8 8 Calculation and expression of results.9 9 Test report.10
SIST EN 14187-9:2006
EN 14187-9:2006 (E) 3 Foreword This European Standard (EN 14187-9:2006) has been prepared by Technical Committee CEN/TC 227 “Road materials”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by August 2006, and conflicting national standards shall be withdrawn at the latest by December 2006. This European Standard is one of a series of standards as listed below: EN 14187-1, Cold applied joint sealants - Part 1:Test method for the determination of rate of cure EN 14187-2, Cold applied joint sealants - Part 2:Test method for the determination of tack free time EN 14187-3, Cold applied joint sealants - Part 3: Test method for the determination of self-levelling properties EN 14187-4, Cold applied joint sealants - Part 4: Test method for the determination of the change in mass and volume after immersion in test fuel EN 14187-5, Cold applied joint sealants - Part 5: Test method for the determination of the resistance to hydrolysis EN 14187-6, Cold applied joint sealants - Part 6: Test method for the determination of the adhesion/cohesion properties after immersion in chemical liquids EN 14187-7, Cold applied joint sealants - Part 7: Test method for the determination of the resistance to flame EN 14187-8, Cold applied joint sealants - Part 8: Test method for the determination of the artificial weathering by UV-irradiation EN 14187-9, Cold applied joint sealants — Part 9: Test method for the function testing of joint sealants No existing European Standard is superseded. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. SIST EN 14187-9:2006
EN 14187-9:2006 (E) 4
1 Scope This European Standard specifies a function test for cold applied joint sealants intended for use in joints in roads and airfield pavements in cold climate areas where the total joint movement can be greater than 35 % and the temperature can go below –25 °C. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 13880-12, Hot applied joint sealants - Part 12: Test method for the manufacture of concrete test blocks for bond testing (recipe methods) EN 14187-2, Cold applied joint sealants
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.