SIST EN 13763-6:2004
(Main)Explosives for civil uses - Detonators and relays - Part 6: Determination of resistance to cracking in low temperatures of leading wires
Explosives for civil uses - Detonators and relays - Part 6: Determination of resistance to cracking in low temperatures of leading wires
This European Standard specifies a method for determining the resistance to cracking at low temperatures of leading wire insulation of detonators. This method is only applicable to electric detonators with plastic covered leading wires.
Explosivstoffe für zivile Zwecke - Zünder und Verzögerungselemente - Teil 6: Bestimmung des Widerstandes der Isolation von Zünderdrähten gegen Rissbildung bei niedrigen Temperaturen
Explosifs a usage civil - Détonateurs et relais - Partie 6: Détermination de la résistance a la fissuration des fils d'amorces a basse température
La présente norme spécifie une méthode permettant de déterminer la résistance a la fissuration a basses températures de l'isolation des fils d'amorce des détonateurs. Cette méthode n'est applicable qu'aux détonateurs électriques comportant des fils d'amorce revetus de plastique.
Eksplozivi za civilno uporabo – Detonatorji in zakasnilniki – 6. del: Ugotavljanje odpornosti vodnikov proti razpokanju pri nizkih temperaturah
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Eksplozivi za civilno uporabo – Detonatorji in zakasnilniki – 6. del: Ugotavljanje odpornosti vodnikov proti razpokanju pri nizkih temperaturahExplosivstoffe für zivile Zwecke - Zünder und Verzögerungselemente - Teil 6: Bestimmung des Widerstandes der Isolation von Zünderdrähten gegen Rissbildung bei niedrigen TemperaturenExplosifs a usage civil - Détonateurs et relais - Partie 6: Détermination de la résistance a la fissuration des fils d'amorces a basse températureExplosives for civil uses - Detonators and relays - Part 6: Determination of resistance to cracking in low temperatures of leading wires71.100.30Eksplozivi. PirotehnikaExplosives. PyrotechnicsICS:Ta slovenski standard je istoveten z:EN 13763-6:2003SIST EN 13763-6:2004en01-januar-2004SIST EN 13763-6:2004SLOVENSKI
STANDARD
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 13763-6November 2003ICS 71.100.30English versionExplosives for civil uses - Detonators and relays - Part 6:Determination of resistance to cracking in low temperatures ofleading wiresExplosifs à usage civil - Détonateurs et relais - Partie 6:Détermination de la résistance à la fissuration des filsd'amorces à basse températureExplosivstoffe für zivile Zwecke - Zünder undVerzögerungselemente - Teil 6: Bestimmung desWiderstandes der Isolation von Zünderdrähten gegenRissbildung bei niedrigen TemperaturenThis European Standard was approved by CEN on 1 September 2003.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and UnitedKingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2003 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 13763-6:2003 E
EN 13763-6:2003 (E)2ContentspageForeword.3Introduction.51Scope.52Normative references.53Terms and definitions.54Test pieces.55Apparatus.66Procedure.67Test report.7Annex A (informative)
Range of applicability of the test method.8Annex ZA (informative)
Clauses of this European Standard addressing essential requirements or otherprovisions of EU Directives.9
EN 13763-6:2003 (E)3ForewordThis document (EN 13763-6:2003) has been prepared by Technical Committee CEN/TC 321 "Explosives for civiluses", the secretariat of which is held by AENOR.This European Standard shall be given the status of a national standard, either by publication of an identical text orby endorsement, at the latest by May 2004, and conflicting national standards shall be withdrawn at the latest byMay 2004.This document has been prepared under a mandate given to CEN by the European Commission and the EuropeanFree Trade Association, and supports essential requirements of EU Directive(s).For the relationship with EU Directive(s), see informative annex ZA, which is an integral part of this standard.This European Standard is one of a series of standards with the generic title Explosives for civil uses – Detonatorsand relays. The other parts of this series are listed below:prEN 13763-1Part 1: RequirementsEN 13763-2Part 2: Determination of thermal stabilityEN 13763-3Part 3: Determination of sensitiveness to impactEN 13763-4Part 4: Determination of resistance to abrasion of leading wires and shock tubesEN 13763-5Part 5: Determination of resistance to cutting damage of leading wires and shock tubesEN 13763-7Part 7: Determination of the mechanical strength of leading wires, shock tubes, connections,crimps and closuresEN 13763-8Part 8: Determination of resistance to vibration of plain detonatorsEN 13763-9Part 9: Determination of resistance to bending of detonatorsEN 13763-11Part 11: Determination of resistance to damage by dropping
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.