SIST EN 13763-9:2004

Explosives for civil uses - Detonators and relays - Part 9: Determination of resistance to bending of detonators

This European Standard specifies a method for determining the resistance of the detonator shell to bending. This standard does not apply to surface connectors.

Explosivstoffe für zivile Zwecke - Zünder und Verzögerungselemente - Teil 9: Bestimmung des Widertandes von Zündern gegen Biegespannung

Explosifs a usage civil - Détonateurs et relais - Partie 9: Détermination de la résistance a la flexion des détonateurs

Eksplozivi za civilno uporabo – Detonatorji in zakasnilniki – 9. del: Ugotavljanje odpornosti detonatorjev proti upogibu

General Information

• Status: Published
• Publication Date: 31-Dec-2003
• ICS: 71.100.30 - Explosives. Pyrotechnics and fireworks
• Technical Committee: IEKS - Explosives
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 01-Jan-2004
• Due Date: 01-Jan-2004
• Completion Date: 01-Jan-2004
• Directive: 2014/28/EU - Directive 2014/28/EU of the European Parliament and of the Council of 26 February 2014 on the harmonisation of the laws of the Member States relating to the making available on the market and supervision of explosives for civil uses
• Directive: TP072 - Pravilnik o tehničnih in varnostnih zahtevah, obrazcih ter evidencah za eksplozive in pirotehnične izdelke
• Mandate: M/055 - Standardization mandate to CEN for explosives for civil uses
• Ref Project: EN 13763-9:2003 - Explosives for civil uses - Detonators and relays - Part 9: Determination of resistance to bending of detonators

Relations

• Revises: oSIST prEN 13763-9:2021 - Explosives for civil uses - Detonators and relays - Part 9: Determination of resistance to bending of detonators
• Effective Date: 18-Jan-2023
• Revises: oSIST prEN 13763-9:2021 - Explosives for civil uses - Detonators and relays - Part 9: Determination of resistance to bending of detonators
• Effective Date: 19-Jan-2023
• Revised: oSIST prEN 13763-9:2021 - Explosives for civil uses - Detonators and relays - Part 9: Determination of resistance to bending of detonators
• Effective Date: 01-Apr-2021

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Eksplozivi za civilno uporabo – Detonatorji in zakasnilniki – 9. del: Ugotavljanje odpornosti detonatorjev proti upogibuExplosivstoffe für zivile Zwecke - Zünder und Verzögerungselemente - Teil 9: Bestimmung des Widertandes von Zündern gegen BiegespannungExplosifs a usage civil - Détonateurs et relais - Partie 9: Détermination de la résistance a la flexion des détonateursExplosives for civil uses - Detonators and relays - Part 9: Determination of resistance to bending of detonators71.100.30Eksplozivi. PirotehnikaExplosives. PyrotechnicsICS:Ta slovenski standard je istoveten z:EN 13763-9:2003SIST EN 13763-9:2004en01-januar-2004SIST EN 13763-9:2004SLOVENSKI
STANDARD



SIST EN 13763-9:2004



EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 13763-9November 2003ICS 71.100.30English versionExplosives for civil uses - Detonators and relays - Part 9:Determination of resistance to bending of detonatorsExplosifs à usage civil - Détonateurs et relais - Partie 9:Détermination de la résistance à la flexion des détonateursExplosivstoffe für zivile Zwecke - Zünder undVerzögerungselemente - Teil 9: Bestimmung desWidertandes von Zündern gegen BiegespannungThis European Standard was approved by CEN on 1 September 2003.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and UnitedKingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2003 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 13763-9:2003 ESIST EN 13763-9:2004



EN 13763-9:2003 (E)2ContentspageForeword.3Introduction.51Scope.52Normative references.53Terms and definitions.54Apparatus.65Test pieces.96Procedure.97Test report.10Annex A (informative)
Range of applicability of the test method.11Annex ZA (informative)
Clauses of this European Standard addressing essential requirements orother provisions of EU Directives.12SIST EN 13763-9:2004



EN 13763-9:2003 (E)3ForewordThis document (EN 13763-9:2003) has been prepared by Technical Committee CEN/TC 321 "Explosives for civiluses", the Secretariat of which is held by AENOR.This European Standard shall be given the status of a national standard, either by publication of an identical text orby endorsement, at the latest by May 2004, and conflicting national standards shall be withdrawn at the latest byMay 2004.This document has been prepared under a mandate given to CEN by the European Commission and the EuropeanFree Trade Association, and supports essential requirements of EU Directive(s).For the relationship with EU Directive(s), see informative annex ZA, which is an integral part of this document.This European Standard is one of a series of standards with the generic title Explosives for civil uses – Detonatorsand relays. The other parts of this series are listed below:prEN 13763-1Part 1: Requirements.EN 13763-2Part 2: Determination of thermal stability.EN 13763-3Part 3: Determination of sensitiveness to impact.EN 13763-4 Part 4: Determination of resistance to abrasion of leading wires and shock tubes.EN 13763-5Part 5: Determination of resistance to cutting damage of leading wires and shock tubes.EN 13763-6Part 6: Determination of resistance to cracking at low temperatures of leading wires.EN 13763-7Part 7: Determination of the mechanical strength of leading wires, shock tubes, connections,crimps and closures.EN 13763-8Part 8: Determination of resistance to vibration of plain detonators.EN 13763-11Part 11: Determination of resistance to damage by dropping of detonators and relays.EN 13763-12 Part 12: Determination of resistance to hydrostatic pressure.prEN 13763-13Part 13: Determination of resistance of electric detonators against electrostatic discharge.prEN 13763-15Part 15: Determination of equivalent initiating capability.prEN 13763-16Part 16: Determination of delay accuracy.prEN 13763-17Part 17: Determination of no-fire current of electric detonators.prEN 13763-18Part 18: Determination of series firing current of electric detonators.prEN 13763-19Part 19: Determination of firing impulse of electric detonators.EN 13763-20Part 20: Determination of total electrical resistance of electric detonators.prEN 13763-21Part 21: Determination of flash-over voltage of electric detonators.SIST EN 13763-9:2004



EN 13763-9:2003 (E)4prEN 13763-22Part 22: Determination of capacitance, insulation resistance and insulation breakdown of leadingwires.EN 13763-23Part 23: Determination of the shock-wave velocity of shock tube.EN 13763-24Part 24: Determination of the electrical non-conductivity of shock tubes.prEN 13763-25Part 25: Determination of transfer capability of surface connectors and coupling accessories.prEN 13763-26Part 26: Definitions, methods and requirements for devices and accessories for reliable and safefunction of detonators and relays.CEN/TS 13763-27Part 27: Definitions, methods and requirements for electronic initiation system.Annex A is informative.According to the CEN/CENELEC Internal Regulations, the national standards organizations of the followingcountries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland,France, Germany, Greece, Hun
...