kSIST FprEN IEC 60034-7:2020

Rotating electrical machines - Part 7: Classification of types of construction, mounting arrangements and terminal box position (IM Code)

2020-01-17 JF: standard does not seem to contain requirements. TC intends to start the vote on removing the link with LVD.

Drehende elektrische Maschinen - Teil 7: Klassifizierung der Bauarten, der Aufstellungsarten und der Klemmkasten-Lage (IM-Code)

Machines électriques tournantes - Partie 7: Classification des formes de construction et les dispositions de montage (Code IM)

l’IEC 60034-7:2020 spécifie le Code IM, une classification des modes de construction, des dispositions de montage et position de la boîte à bornes des machines électriques tournantes. Deux systèmes de classification sont prévus comme suit: - Code I: Désignation alphanumérique applicable aux machines à flasque(s) palier(s) et à un seul bout d'arbre - Code II: Désignation numérique applicable à une plus large plage de types de machines, y compris les types couverts par le Code I Cette troisième édition annule et remplace la deuxième édition, parue en 1992, ainsi que son Amendement 1:2000. Cette édition inclut les modifications techniques majeures suivantes par rapport à l'édition précédente: - ajout de la note relative aux moteurs doubles - référence à 4.3 remplaçant la répétition du texte - nouveau paragraphe relatif au marquage de l’inclinaison ou de la déclinaison de l’arbre

Električni rotacijski stroji - 7. del: Razvrstitev vrst konstrukcije, montaže in položaja priključne omare (koda IM)

General Information

• Status: Not Published
• Public Enquiry End Date: 30-Mar-2020
• ICS: 29.160.01 - Rotating machinery in general
• Technical Committee: ERS - Rotating machinery
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 05-Apr-2022
• Due Date: 10-Jun-2022
• Directive: 2014/35/EU - Directive 2014/35/EU of the European Parliament and of the Council of 26 February 2014 on the harmonisation of the laws of the Member States relating to the making available on the market of electrical equipment designed for use within certain voltage limits
• Mandate: M/511 - Mandate to CEN, CENELEC and ETSI relating to harmonised standards in the field of the Low Voltage Directive
• Ref Project: EN IEC 60034-7:2022 - Rotating electrical machines - Part 7: Classification of types of construction, mounting arrangements and terminal box position (IM Code)

RELATIONS

• Revised: SIST EN 60034-7:1999/A1:2002 - Rotating electrical machines -- Part 7: Classification of types of construction, mounting arrangements and terminal box position (IM Code)
• Effective Date: 10-Dec-2019
• Revised: SIST EN 60034-7:1999 - Rotating electrical machines -- Part 7: Classification of types of construction, mounting arrangements and terminal box position (IM Code)
• Effective Date: 04-Dec-2018
• Replaces: SIST EN 60034-7:1999 - Rotating electrical machines -- Part 7: Classification of types of construction, mounting arrangements and terminal box position (IM Code)
• Effective Date: 29-Mar-2022
• Replaces: SIST EN 60034-7:1999/A1:2002 - Rotating electrical machines -- Part 7: Classification of types of construction, mounting arrangements and terminal box position (IM Code)
• Effective Date: 29-Mar-2022

Standards Content (sample)

SLOVENSKI STANDARD
oSIST prEN IEC 60034-7:2020
01-marec-2020
Električni rotacijski stroji - 7. del: Razvrstitev vrst konstrukcije, montaže in
položaja priključne omare (koda IM)

Rotating electrical machines - Part 7: Classification of types of construction, mounting

arrangements and terminal box position (IM Code)

Machines électriques tournantes - Partie 7: Classification des formes de construction et

les dispositions de montage (Code IM)
Ta slovenski standard je istoveten z: prEN IEC 60034-7:2020
ICS:
29.160.01 Rotacijski stroji na splošno Rotating machinery in
general
oSIST prEN IEC 60034-7:2020 en,fr,de

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN IEC 60034-7:2020
---------------------- Page: 2 ----------------------
oSIST prEN IEC 60034-7:2020
2/1976/CDV
COMMITTEE DRAFT FOR VOTE (CDV)
PROJECT NUMBER:
IEC 60034-7 ED3
DATE OF CIRCULATION: CLOSING DATE FOR VOTING:
2020-01-17 2020-04-10
SUPERSEDES DOCUMENTS:
2/1938/CD, 2/1950A/CC
IEC TC 2 : ROTATING MACHINERY
SECRETARIAT: SECRETARY:
United Kingdom Mr Charles Whitlock
OF INTEREST TO THE FOLLOWING COMMITTEES: PROPOSED HORIZONTAL STANDARD:
Other TC/SCs are requested to indicate their interest, if any, in
this CDV to the secretary.
FUNCTIONS CONCERNED:
EMC ENVIRONMENT QUALITY ASSURANCE SAFETY

SUBMITTED FOR CENELEC PARALLEL VOTING NOT SUBMITTED FOR CENELEC PARALLEL VOTING

Attention IEC-CENELEC parallel voting
The attention of IEC National Committees, members of
CENELEC, is drawn to the fact that this Committee Draft for
Vote (CDV) is submitted for parallel voting.
The CENELEC members are invited to vote through the
CENELEC online voting system.

This document is still under study and subject to change. It should not be used for reference purposes.

Recipients of this document are invited to submit, with their comments, notification of any relevant patent rights of which they are

aware and to provide supporting documentation.
TITLE:

Rotating electrical machines – Part 7: Classification of types of construction, mounting arrangements and

terminal box position (IM Code)
PROPOSED STABILITY DATE: 2022
NOTE FROM TC/SC OFFICERS:

Copyright © 2019 International Electrotechnical Commission, IEC. All rights reserved. It is permitted to download this

electronic file, to make a copy and to print out the content for the sole purpose of preparing National Committee positions.

You may not copy or "mirror" the file or printed version of the document, or any part of it, for any other purpose without

permission in writing from IEC.
---------------------- Page: 3 ----------------------
oSIST prEN IEC 60034-7:2020
– 2 – IEC CDV 60034-7 © IEC 2020
CONTENTS
Page

FOREWORD ........................................................................................................................... 4

Section 1: Scope .......................................................................................................... 5

Section 2: Normative references .................................................................................. 5

Section 3: Definitions ................................................................................................... 5

3.1 type of construction ................................................................................................. 5

3.2 mounting arrangement............................................................................................. 5

3.3 shaft extension ........................................................................................................ 5

3.4 drive-end of a machine (D-end) ............................................................................... 6

3.5 non-drive end of the machine (N-end) ..................................................................... 6

Section 4: Code I (alpha-numeric designation) ............................................................. 6

4.1 Designation of machines with horizontal shafts ....................................................... 6

4.2 Designation of machines with vertical shafts............................................................ 9

4.3 Terminal box location ............................................................................................ 11

Section 5: Code II (all-numeric designation) ............................................................... 12

5.1 Designation ........................................................................................................... 12

5.2 Significance of the first numeral ............................................................................ 12

5.3 Significance of the fourth numeral ......................................................................... 13

5.4 Significance of the second and third numerals ....................................................... 13

5.5 Terminal box location ............................................................................................ 13

5.6 Examples of designations ...................................................................................... 13

5.7 Inclination or declination of shaft ........................................................................... 13

Annex A (informative) Relationship between Code I and Code II ......................................... 23

Table 1 – Designations for machines with horizontal shafts (IM B...) ....................................... 7

Table 2 – Designations for machines with vertical shafts (IM V...) ........................................... 9

Table 3 – Significance of the first numeral ............................................................................ 12

Table 4 – Significance of the fourth numeral ......................................................................... 13

Table 5 – Significance of second and third numerals for first numeral 1

(Foot-mounted machines with endshield bearing(s) only) ...................................................... 14

Table 6 – Significance of second and third numerals for first numeral 2

(Foot-and-flange-mounted machines with endshield bearing(s) only) .................................... 15

Table 7 – Significance of second and third numerals for first numeral 3

(Flange-mounted machines with endshield bearing(s) only with a flange part of an endshield) ....... 16

Table 8 – Significance of second and third numerals for first numeral 4
(Flange-mounted machines with endshield bearing(s) only with a flange not part

of an endshield, but an integral part of the frame or other component) .................................. 17

Table 9 – Significance of second and third numerals for first numeral 5

(Machines without bearings) ................................................................................................. 18

Table 10 – Significance of second and third numerals for first numeral 6

(Machines with endshield bearings and pedestal bearings) ................................................... 19

Table 11 – Significance of second and third numerals for first numeral 7

(Machines with pedestal bearings only)................................................................................. 20

---------------------- Page: 4 ----------------------
oSIST prEN IEC 60034-7:2020
IEC CDV 60034-7 © IEC 2020 – 3 –
Page
Table 12 – Significance of second and third numerals for first numeral 8

(Vertical machines of construction not covered by first numerals 1 to 4) ............................... 21

Table 13 – Significance of second and third numerals for first numeral 9

(Machines with special mounting arrangements) ................................................................... 22

Table A.1 – Relationship between Code I and Code II for machines

with horizontal shafts (IM B..)................................................................................................ 23

Table A.2 – Relationship between Code I and Code II for machines

with vertical shafts (IM V..) ................................................................................................... 23

---------------------- Page: 5 ----------------------
oSIST prEN IEC 60034-7:2020
– 4 – IEC CDV 60034-7 © IEC 2020
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
ROTATING ELECTRICAL MACHINES –
Part 7: Classification of types of construction, mounting arrangements
and terminal box position (IM Code)
FOREWORD

1) The IEC (International Electrotechnical Commission) is a worldwide organization for standardization comprising

all national electrotechnical committees (IEC National Committees). The object of the IEC is to promote

international co-operation on all questions concerning standardization in the electrical and electronic fields. To

this end and in addition to other activities, the IEC publishes International Standards. Their preparation is

entrusted to technical committees; any IEC National Committee interested in the subject dealt with may

participate in this preparatory work. International, governmental and non-governmental organizations liaising

with the IEC also participate in this preparation. The IEC collaborates closely with the International

Organization for Standardization (ISO) in accordance with conditions determined by agreement between the

two organizations.

2) The formal decisions or agreements of the IEC on technical matters express, as nearly as possible, an

international consensus of opinion on the relevant subjects since each technical committee has representation

from all interested National Committees.

3) The documents produced have the form of recommendations for international use and are published in the form

of standards, technical specifications, technical reports or guides and they are accepted by the National

Committees in that sense.

4) In order to promote international unification, IEC National Committees undertake to apply IEC International

Standards transparently to the maximum extent possible in their national and regional standards. Any

divergence between the IEC Standard and the corresponding national or regional standard shall be clearly

indicated in the latter.

5) The IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any

equipment declared to be in conformity with one of its standards.

6) Attention is drawn to the possibility that some of the elements of this International Standard may be the subject

of patent rights. The IEC shall not be held responsible for identifying any or all such patent rights.

International Standard IEC 60034-7: Classification of types of construction, mounting

arrangements and terminal box position (IM Code), has been prepared by IEC technical

committee 2: Rotating machinery.

This third edition cancels and replaces edition 2.1 published in 2000. It constitutes a technical

revision. The main technical changes with regard to the previous edition are as follows:

Clause Change
5.4 Note on twin motors added
5.5 Reference to Clause 4.3 instead of duplication of text
5.7 New clause on marking of shaft inclination or declination

This publication will remain unchanged until 20xx. At this date, the publication will be

• reconfirmed;
• withdrawn;
• replaced by a revised edition, or
• amended.
2WG 12(Sec)249
---------------------- Page: 6 ----------------------
oSIST prEN IEC 60034-7:2020
IEC CDV 60034-7 © IEC 2020 – 5 –
1 ROTATING ELECTRICAL MACHINES –
3 Part 7: Classification of types of construction, mounting arrangements
4 and terminal box position (IM Code)
8 Section 1: Scope

9 This part of IEC 60034 specifies the IM Code, a classification of types of construction,

10 mounting arrangements and the terminal box position of rotating electrical machines.

11 Two systems of classification are provided as follows:

12 – Code I (see section 2): An alpha-numeric designation applicable to machines with end-

13 shield bearing(s) and only one shaft extension.

14 – Code II (see section 3): An all-numeric designation applicable to a wider range of types

15 of machines including types covered by Code I.

16 The type of machine not covered by Code II should be fully described in words.

17 The relationship between Code I and Code II is given in annex A.
18 Section 2: Normative references
19 Section 3: Definitions
20 For the purposes of this part of IEC 60034, the following definitions apply:
21 3.1 type of construction

22 the arrangement of machine components with regard to fixings, bearing arrangement and

23 shaft extension
24 (IEV 60411-13-34)
25 3.2 mounting arrangement

26 the orientation on site of the machine as the whole with regard to shaft alignment and position

27 of fixings
28 (IEV 60411-13-35)
29 3.3 shaft extension
30 a portion of a shaft extending beyond an extreme bearing
31 (IEV 60411-13-07)

32 NOTE The bearing may be on the machine itself or be part of an assembly comprising a machine and (an)

33 additional bearing(s).
________

IEC 60050(411): 1973, International Electrotechnical Vocabulary (IEV) – Chapter 411: Rotating machinery.

---------------------- Page: 7 ----------------------
oSIST prEN IEC 60034-7:2020
– 6 – IEC CDV 60034-7 © IEC 2020
35 3.4 drive-end of a machine (D-end)
36 that end of the machine which accommodates the shaft end
37 (IEV 60411-13-36)

38 NOTE This is normally the driving end of a motor or the driven end of a generator.

39 Where for some machines the above definition is inadequate, the D-end is defined as follows:

40 a) Machine with two shaft extensions of different diameter: the end with the larger shaft

41 diameter;

42 b) Machine with a cylindrical shaft extension and a conical shaft extension of the same

43 diameter: the end with cylindrical shaft extention;

44 c) Machine with other arrangements: according to IEC 60034-8 if applicable; otherwise by

45 agreement.

46 NOTE The outer diameter of a forged-on flange is taken to be the diameter of the shaft extension.

47 3.5 non-drive end of the machine (N-end)
48 that end of the machine opposite to the drive end
49 (IEV 60411-13-37).
51 Section 4: Code I (alpha-numeric designation)
52 4.1 Designation of machines with horizontal shafts

53 In Code I, a machine with a horizontal shaft is designated by the code letters IM (International

54 Mounting), followed by a space, the letter B, one or two numerals as shown in Table 1 and an

55 optional letter as shown in clause 4.3.
---------------------- Page: 8 ----------------------
oSIST prEN IEC 60034-7:2020
IEC CDV 60034-7 © IEC 2020 – 7 –
57 Table 1 – Designations for machines with horizontal shafts (IM B...)
Type of construction
Mounting
Number
Desig-
Sketch arrangement
of end-
nation
Feet Flange Other details
(Horizontal shaft)
shields
bearings
With Mounted by feet,
IM B3 2 – –
feet feet down
Endshield flange at
With Mounted on D-end
D-end with access
IM B5 2 –
flange side of flange
to back
Mounted by feet,
With
IM B6 2 – – feet left
feet
(viewed from D-end)
Mounted by feet,
With
IM B7 2 – – feet right
feet
(viewed from D-end)
With Mounted by feet,
IM B8 2 – –
feet feet up
No endshield or Mounted on end face
IM B9 1 – –
bearing at D-end of frame at D-end
With Special flange Mounted on D-end
IM B10 2 –
flange at D-end side of flange
Endshield spigot.
With Mounted on D-end
IM B14 2 – No access to back
flange side of flange
Flange at D-end
---------------------- Page: 9 ----------------------
oSIST prEN IEC 60034-7:2020
– 8 – IEC CDV 60034-7 © IEC 2020
59 Table 1 (continued)
Type of construction
Mounting
Number
Desig-
Sketch arrangement
of end-
nation
Feet Flange Other details
(Horizontal shaft)
shields
bearings
No endshield or
Mounted by feet,
bearing at D-end.
With feet down, with addi-
IM B15 1 – Additional mounting
feet tional mounting on
provisions on D-end
end face of frame
of frame
With
Mounted by feet,
IM B20 2 raised – –
feet down
feet
Mounted by feet,
With Endshield flange
With feet down, with addi-
IM B25 2 raised at D-end with access
flange tional mounting
feet to back
on flange
3 or 4 pads on
IM B30 2 – – Pad mounted
endshield(s) or frame
Mounted by feet,
Endshield spigot
With With feet down, with addi-
IM B34 2 No access to back
feet flange tional mounting on
Flange at D-end
D-end side of flange
Mounted by feet,
Endshield flange at
With With feet down, with addi-
IM B35 2 D-end with access
feet flange tional mounting on
to back
D-end side of flange
---------------------- Page: 10 ----------------------
oSIST prEN IEC 60034-7:2020
IEC CDV 60034-7 © IEC 2020 – 9 –
61 4.2 Designation of machines with vertical shafts

62 In Code I, a machine with a vertical shaft is designated by the code letters IM (International

63 mounting), followed by a space, the letter V, one or two numerals as shown in Table 2 and an

64 optional letter as shown in Clause 4.3.
65 Table 2 – Designations for machines with vertical shafts (IM V...)
Type of construction
Mounting
Number
Desig-
Sketch arrangement
of end-
nation
Feet Flange Other details
(Vertical shaft)
shields
bearings
Endshield flange at Mounted on D-end
With
IM V1 2 – D-end with access side of flange,
flange
to back D-end down
Endshield flange at Mounted on N-end
With
IM V2 2 – N-end with access side of flange,
flange
to back D-end up
Endshield flange at Mounted on D-end
With
IM V3 2 – D-end with access side of flange,
flange
to back D-end up
Endshield flange at Mounted on N-end
With
IM V4 2 – N-end with access side of flange,
flange
to back D-end down
With Mounted by feet,
IM V5 2 – –
feet D-end down
With Mounted by feet,
IM V6 2 – –
feet D-end up
---------------------- Page: 11 ----------------------
oSIST prEN IEC 60034-7:2020
– 10 – IEC CDV 60034-7 © IEC 2020
67 Table 2 (continued)
...