SIST EN 61754-20-100:2012

Fibre optic interconnecting devices and passive components - Fibre optic connector interfaces - Part 20-100: Interface standard for LC connectors with protective housings related to IEC 61076-3-106 (IEC 61754-20-100:2012)

This part of IEC 61754 covers connectors with protective housings. The housing is defined as variant 4 in IEC 61076-3-106:2006. These connectors use a push-pull coupling mechanism. To connect the fibres inside the housing the LC interface is used as described in IEC 61754-20:2002. The fully assembled variants (connectors) described in this document incorporate fixed and free connectors.

Lichtwellenleiter - Verbindungselemente und passive Bauteile - Steckgesichter von Lichtwellenleiter-Steckverbindern - Teil 20-100: Steckverbinderfamilie der Bauart LC mit Schutzgehäusen nach IEC 61076-3-106 (IEC 61754-20-100:2012)

Dispositifs d'interconnexion et composants passifs à fibres optiques - Interfaces de connecteurs pour fibres optiques - Partie 20-100: Norme d’interface pour les connecteurs de type LC avec boitiers de protection liés à la norme CEI 61076-3-106 (CEI 61754-20-100:2012)

IEC 61754-20-100:2012 couvre les connecteurs avec boîtiers de protection. Le boîtier est défini comme la variante 4 de l’IEC 61076-3-106:2006. Ces connecteurs utilisent un mécanisme d'accouplement pousser-tirer. Pour connecter les fibres à l'intérieur du boîtier, l'interface LC est utilisée comme cela est décrit dans l’IEC 61754-20:2002. Les variantes entièrement assemblées (connecteurs) décrites dans le présent document comprennent des embases et des fiches.

Optični spojni elementi in pasivne komponente - Optični konektorski vmesniki - 20-100. del: Vmesniški standard za konektorje LC z zaščitnim ohišjem po IEC 61076-3-106 (IEC 61754-20-100:2012)

Ta del standarda IEC 61754 zajema konektorje z zaščitnimi ohišji. Ohišje je v standardu IEC 61076-3-106:2006 opredeljeno kot različica 4. Ti konektorji uporabljajo potisno vlečni mehanizem stika. Za povezovanje vlaken v ohišju se uporablja vmesnik LC, kot je opisano v standardu IEC 61754-20:2002. V celoti sestavljene različice (konektorji), ki so opisane v tem dokumentu, vključujejo fiksne in proste konektorje.

General Information

• Status: Published
• Publication Date: 23-Sep-2012
• ICS: 33.180.20 - Fibre optic interconnecting devices
• Technical Committee: iTEL - Communication cables
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 30-Aug-2012
• Due Date: 04-Nov-2012
• Completion Date: 24-Sep-2012
• Ref Project: EN 61754-20-100:2012 - Fibre optic interconnecting devices and passive components - Fibre optic connector interfaces - Part 20-100: Interface standard for LC connectors with protective housings related to IEC 61076-3-106

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 61754-20-100:2012
01-oktober-2012
2SWLþQLVSRMQLHOHPHQWLLQSDVLYQHNRPSRQHQWH2SWLþQLNRQHNWRUVNLYPHVQLNL
GHO9PHVQLãNLVWDQGDUG]DNRQHNWRUMH/&]]DãþLWQLPRKLãMHPSR,(&
,(&
Fibre optic interconnecting devices and passive components - Fibre optic connector
interfaces - Part 20-100: Interface standard for LC connectors with protective housings
related to IEC 61076-3-106 (IEC 61754-20-100:2012)
Lichtwellenleiter - Verbindungselemente und passive Bauteile - Steckgesichter von
Lichtwellenleiter-Steckverbindern - Teil 20-100: Steckverbinderfamilie der Bauart LC mit
Schutzgehäusen nach IEC 61076-3-106 (IEC 61754-20-100:2012)
Dispositifs d'interconnexion et composants passifs à fibres optiques - Interfaces de
connecteurs pour fibres optiques - Partie 20-100: Norme d’interface pour les connecteurs
de type LC avec boitiers de protection liés à la norme CEI 61076-3-106 (CEI 61754-20-
100:2012)
Ta slovenski standard je istoveten z: EN 61754-20-100:2012
ICS:
33.180.20 3RYH]RYDOQHQDSUDYH]D Fibre optic interconnecting
RSWLþQDYODNQD devices
SIST EN 61754-20-100:2012 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 61754-20-100:2012

---------------------- Page: 2 ----------------------

SIST EN 61754-20-100:2012

EUROPEAN STANDARD
EN 61754-20-100

NORME EUROPÉENNE
August 2012
EUROPÄISCHE NORM

ICS 33.180.20


English version


Fibre optic interconnecting devices and passive components -
Fibre optic connector interfaces -
Part 20-100: Interface standard for LC connectors with protective
housings related to IEC 61076-3-106
(IEC 61754-20-100:2012)


Dispositifs d'interconnexion et composants Lichtwellenleiter-Verbindungselemente
passifs à fibres optiques - Interfaces und passive Bauteile -
de connecteurs pour fibres optiques - Steckgesichter von Lichtwellenleiter-
Partie 20-100: Norme d’interface Steckverbindern -
pour les connecteurs de type LC Teil 20-100: Steckverbinderfamilie
avec boitiers de protection liés der Bauart LC mit Schutzgehäusen
à la norme CEI 61076-3-106 nach IEC 61076-3-106
(CEI 61754-20-100:2012) (IEC 61754-20-100:2012)



This European Standard was approved by CENELEC on 2012-06-27. CENELEC members are bound to comply
with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the CEN-CENELEC Management Centre or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and notified
to the CEN-CENELEC Management Centre has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus,
the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany,
Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.

CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

Management Centre: Avenue Marnix 17, B - 1000 Brussels


© 2012 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 61754-20-100:2012 E

---------------------- Page: 3 ----------------------

SIST EN 61754-20-100:2012
EN 61754-20-100:2012 - 2 -
Foreword
The text of document 86B/3386/FDIS, future edition 1 of IEC 61754-20-100, prepared by IEC/SC 86B
"Fibre optic interconnecting devices and passive components" of IEC/TC 86 "Fibre optics" was
submitted to the IEC-CENELEC parallel vote and approved by CENELEC as EN 61754-20-100:2012.
The following dates are fixed:
(dop) 2013-03-27
• latest date by which the document has
to be implemented at national level by
publication of an identical national
standard or by endorsement
(dow) 2015-06-27
• latest date by which the national
standards conflicting with the
document have to be withdrawn

Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such
patent rights.

Endorsement notice
The text of the International Standard IEC 61754-20-100:2012 was approved by CENELEC as a
European Standard without any modification.
In the official version, for Bibliography, the following note has to be added for the standard indicated :

IEC 61754-1 NOTE Harmonised as EN 61754-1.

---------------------- Page: 4 ----------------------

SIST EN 61754-20-100:2012
- 3 - EN 61754-20-100:2012
Annex ZA
(normative)

Normative references to international publications
with their corresponding European publications

The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.

NOTE  When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD
applies.

Publication Year Title EN/HD Year

IEC 60050-581 - International Electrotechnical Vocabulary - -
(IEV) -
Part 581: Electromechanical components for
electronic equipment


IEC 60050-731 - International Electrotechnical Vocabulary - -
(IEV) -
Chapter 731: Optical fibre communication


IEC 60529 - Degrees of protection provided by EN 60529 -
enclosures (IP Code)


IEC 61076-3-106 2006 Connectors for electronic equipment - EN 61076-3-106 2006
Product requirements -
Part 3-106: Rectangular connectors - Detail
specification for protective housings for use
with 8-way shielded and unshielded
connectors for industrial environments
incorporating the IEC 60603-7 series
interface


IEC 61754-20 2002 Fibre optic connector interfaces - EN 61754-20 2002
Part 20: Type LC connector family

---------------------- Page: 5 ----------------------

SIST EN 61754-20-100:2012

---------------------- Page: 6 ----------------------

SIST EN 61754-20-100:2012



IEC 61754-20-100

®


Edition 1.0 2012-05




INTERNATIONAL



STANDARD



















Fibre optic interconnecting devices and passive components – Fibre optic

connector interfaces –

Part 20-100: Interface standard for LC connectors with protective housings


related to IEC 61076-3-106
























INTERNATIONAL

ELECTROTECHNICAL

COMMISSION

PRICE CODE
Q


ICS 33.180.20 ISBN 978-2-88912-065-9



  Warning! Make sure that you obtained this publication from an authorized distributor.


® Registered trademark of the International Electrotechnical Commission

---------------------- Page: 7 ----------------------

SIST EN 61754-20-100:2012
– 2 – 61754-20-100 © IEC:2012(E)
CONTENTS

FOREWORD . 3
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 Description . 5
5 Interfaces . 6
5.1 General . 6
5.2 Industrial IEC 61754-20-100, free duplex plug connector . 7
5.3 Industrial IEC 61754-20-100 fixed adaptor connector and active device
receptacle . 11
5.4 Panel cut out . 16
Bibliography . 17

Figure 1 – Free connector . 7
Figure 2 – Details of the front view . 8
Figure 3 – Cross section B – B . 9
Figure 4 – Fixed connector and active device receptacle . 12
Figure 5 – Details of the front view . 13
Figure 6 – Cross section D – D . 14
Figure 7 – Panel cut out . 16

Table 1 – Plug to Adaptor/Receptacle intermateability . 6
Table 2 – Plug to Plug intermateability . 6
Table 3 – Dimensions for free connector . 10
Table 4 – Plug connector interface – Ferrule grade . 11
Table 5 – Dimensions for fixed connector . 15
Table 6 – Dimensions of panel cut out (Figure 7) . 16

---------------------- Page: 8 ----------------------

SIST EN 61754-20-100:2012
61754-20-100 © IEC:2012(E) – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________

FIBRE OPTIC INTERCONNECTING DEVICES
AND PASSIVE COMPONENTS –
FIBRE OPTIC CONNECTOR INTERFACES –

Part 20-100: Interface standard for LC connectors
with protective housings related to IEC 61076-3-106


FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 61754-20-100 has been prepared by subcommittee 86B: Fibre
optic interconnecting devices and passive componen
...