SIST ENV 1329-2:2002

Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Unplasticized poly(vinyl chloride) (PVC-U) - Part 2: Guidance for the assessment of conformity

This part of prEN 1329 specifies procedures and requirements for the assessment of conformity to be included in the manufacturer's quality plan as part of the quality system for third party certification of conformity by a certification body accredited to EN 45011 or EN 45012, as applicable. This standard includes: a) Requirements for materials, components, joints and assemblies given in prEN 1329-1. b) Requirements for the manufacturer's quality system given in EN ISO 9001 or EN ISO 9002, as applicable.

Kunststoff-Rohrleitungssysteme zum Ableiten von Abwasser (niedriger und hoher Temperatur) innerhalb der Gebäudestruktur - Weichmacherfreies Polyvinylchlorid (PVC-U) - Teil 2: Empfehlungen für die Beurteilung der Konformität

Anwendungsbereich
Diese Vornorm gibt Empfehlungen für die Beurteilung der Konformität, die als Teil des Qualitätssicherungssystems im Qualitätssicherungsplan des Herstellers enthalten sein müssen.
Dieser Teil der EN 1329 enthält:
a) Anforderungen an Werkstoffe, Rohrleitungsteile sowie an Verbindungen und Bauteilkombinationen, die in EN 1329-1:1999 festgelegt sind;
b) Anforderungen an das Qualitätssicherungssystem des Herstellers.
ANMERKUNG 1   Es wird empfohlen, dass das Qualitätssicherungssystem, in Abhängigkeit der Anwendung, EN ISO 9001 entspricht.
c) Definitionen und Verfahren im Falle der Zertifizierung durch unparteiische Dritte.
ANMERKUNG 2   Es wird empfohlen, die Zertifizierung durch eine unabhängige Zertifizierungsstelle durchführen zu lassen, die, in Abhängigkeit der Anwendung, nach EN 45011 oder EN 45012 zugelassen ist.
Diese Vornorm gilt für Vollwand-Rohrleitungssysteme aus weichmacherfreiem Polyvinylchlorid (PVC-U) für
Abwasserleitungen, die in Schwerkraftentwässerungssystemen innerhalb von Gebäuden (Anwendungskenn-zeichen ?B") sowie innerhalb von Gebäuden und erdverlegt innerhalb der Gebäudestruktur (Anwendungskenn-zeichen ?BD") zum Ableiten von Abwasser (niedriger und hoher Temperatur) eingesetzt werden. Die Wahl des Anwendungsgebietes wird durch die Kennzeichnung ?B" bzw. ?BD" der Rohrleitungsteile angezeigt.

Systemes de canalisations en plastique pour l'évacuation des eaux-vannes et des eaux usées (a basse et a haute température) a l'intérieur de la structure des bâtiments - Poly(chlorure de vinyle) non plastifié (PVC-U) - Partie 2: Guide pour l'évaluation de la conformité

Domaine d'application
La présente prénorme européenne donne un guide pour l'évaluation de la conformité, a inclure dans le plan qualité du fabricant comme partie de son systeme qualité.
Cette prénorme comprend :
a) les exigences pour les matieres, les composants, les bagues d'étanchéité et les assemblages, données dans l'EN 1329-1:1999 ;
b) les exigences pour le systeme qualité du fabricant.
NOTE 1   Il est recommandé que le systeme qualité se conforme a l'EN ISO 9001 ;
c) des définitions et des procédures a appliquer si une certification par tierce partie a lieu.
NOTE 2   Dans le cas d'une certification par tierce partie, il est recommandé que l'organisme certificateur soit accrédité selon l'EN 45011 ou l'EN 45012, selon le cas.
Cette partie de l'EN 1329 s'applique aux systemes de canalisation fabriqués a partir de poly(chlorure de vinyle) non plastifié (PVC-U) destinés a etre utilisés pour l'évacuation des eaux-vannes et des eaux usées (a base et haute température) a l'intérieur de la structure des bâtiments (code de zone d'application "B") et pour les systemes d'évacuation pour les eaux-vannes et les eaux usées a la fois a l'intérieur du bâtiment et enterré dans la structure du bâtiment (code de zone d'application "BD"). Ceci est repéré au niveau du marquage des produits par "B" et "BD".

Cevni sistemi iz polimernih materialov za nizko- in visokotemperaturne odvodne sisteme v zgradbah - Nemehčan polivinilklorid (PVC-U) - 2. del: Navodilo za ugotavljanje skladnosti

General Information

• Status: Withdrawn
• Publication Date: 31-May-2002
• Withdrawal Date: 02-Aug-2012
• ICS: 23.040.01 - Pipeline components and pipelines in general
• ICS: 91.140.80 - Drainage systems
• Technical Committee: PCV - Plastic pipes, fittings and valves
• Current Stage: 9900 - Withdrawal (Adopted Project)
• Start Date: 02-Aug-2012
• Due Date: 25-Aug-2012
• Completion Date: 03-Aug-2012
• Directive: 89/106/EEC - Construction products
• Ref Project: ENV 1329-2:2001 - Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Unplasticized poly(vinyl chloride) (PVC-U) - Part 2: Guidance for the assessment of conformity

Relations

• Replaced By: SIST-TS CEN/TS 1329-2:2012 - Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Unplasticized poly(vinyl chloride) (PVC-U) - Part 2: Guidance for the assessment of conformity
• Effective Date: 01-Sep-2012

Standards Content (Sample)

SLOVENSKI STANDARD
SIST ENV 1329-2:2002
01-junij-2002
&HYQLVLVWHPLL]SROLPHUQLKPDWHULDORY]DQL]NRLQYLVRNRWHPSHUDWXUQHRGYRGQH
VLVWHPHY]JUDGEDK1HPHKþDQSROLYLQLONORULG39&8GHO1DYRGLOR]D
XJRWDYOMDQMHVNODGQRVWL
Plastics piping systems for soil and waste discharge (low and high temperature) within
the building structure - Unplasticized poly(vinyl chloride) (PVC-U) - Part 2: Guidance for
the assessment of conformity
Kunststoff-Rohrleitungssysteme zum Ableiten von Abwasser (niedriger und hoher
Temperatur) innerhalb der Gebäudestruktur - Weichmacherfreies Polyvinylchlorid (PVC-
U) - Teil 2: Empfehlungen für die Beurteilung der Konformität
Systemes de canalisations en plastique pour l'évacuation des eaux-vannes et des eaux
usées (a basse et a haute température) a l'intérieur de la structure des bâtiments - Poly
(chlorure de vinyle) non plastifié (PVC-U) - Partie 2: Guide pour l'évaluation de la
conformité
Ta slovenski standard je istoveten z: ENV 1329-2:2001
ICS:
23.040.01 Deli cevovodov in cevovodi Pipeline components and
na splošno pipelines in general
91.140.80 Drenažni sistemi Drainage systems
SIST ENV 1329-2:2002 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST ENV 1329-2:2002

---------------------- Page: 2 ----------------------

SIST ENV 1329-2:2002
EUROPEAN PRESTANDARD
ENV 1329-2
PRÉNORME EUROPÉENNE
EUROPÄISCHE VORNORM
May 2001
ICS 23.040.01; 91.140.80
English version
Plastics piping systems for soil and waste discharge (low and
high temperature) within the building structure - Unplasticized
poly(vinyl chloride) (PVC-U) - Part 2: Guidance for the
assessment of conformity
Systèmes de canalisations en plastique pour l'évacuation Kunststoff-Rohrleitungssysteme zum Ableiten von
des eaux-vannes et des eaux usées (à basse et à haute Abwasser (niedriger und hoher Temperatur) innerhalb der
température) à l'intérieur de la structure des bâtiments - Gebäudestruktur - Weichmacherfreies Polyvinylchlorid
Poly(chlorure de vinyle) non plastifié (PVC-U) - Partie 2: (PVC-U) - Teil 2: Empfehlungen für die Beurteilung der
Guide pour l'évaluation de la conformité Konformität
This European Prestandard (ENV) was approved by CEN on 8 March 2001 as a prospective standard for provisional application.
The period of validity of this ENV is limited initially to three years. After two years the members of CEN will be requested to submit their
comments, particularly on the question whether the ENV can be converted into a European Standard.
CEN members are required to announce the existence of this ENV in the same way as for an EN and to make the ENV available promptly
at national level in an appropriate form. It is permissible to keep conflicting national standards in force (in parallel to the ENV) until the final
decision about the possible conversion of the ENV into an EN is reached.
CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,
Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2001 CEN All rights of exploitation in any form and by any means reserved Ref. No. ENV 1329-2:2001 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST ENV 1329-2:2002
Page 2
ENV 1329-2:2001
Contents
Page
Foreword .3
Introduction .4
1  Scope.5
2  Normative references.5
3  Definitions, symbols and abbreviations .5
3.1  Definitions.5
3.2  Abbreviations.7
4  Requirements .8
4.1  General.8
4.2  Testing and inspection.8
Bibliography .19

---------------------- Page: 4 ----------------------

SIST ENV 1329-2:2002
Page 3
ENV 1329-2:2001
Foreword
This European Prestandard has been prepared by Technical Committee CEN/TC 155 "Plastics piping
systems and ducting systems", the secretariat of which is held by NEN.
This prestandard can be used to support elaboration of national third party certification procedure for
products conforming to EN 1329-1:1999.
This prestandard is a Part of a System Standard for plastics piping systems of a particular material for
a specified application. There are a number of such System Standards.
System Standards are based on the results of the work undertaken in ISO/TC 138 "Plastics pipes,
fittings and valves for the transport of fluids", which is a Technical Committee of the International
Organization for Standardisation (ISO).
They are supported by separate standards on test methods to which references are made throughout
the System Standard.
The System Standards are consistent with general standards on functional requirements and on
recommended practice for installation.
EN 1329 consists of the following Parts, under the general title "Plastics piping systems for soil and
waste discharge (low and high temperature) within the building structure — Unplasticized poly(vinyl
chloride) (PVC-U)"

Part 1: Specifications for pipes, fittings and the system ;

 Part 2: Guidance for the assessment of conformity ;
The Recommended practice for installation is dealt with in ENV 13801.
This part of EN 1329 includes a bibliography.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to announce this European Prestandard: Austria, Belgium, Czech
Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg,
Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom.

---------------------- Page: 5 ----------------------

SIST ENV 1329-2:2002
Page 4
ENV 1329-2:2001
Introduction
The System Standard, of which this is Part 2, specifies the requirements for a piping system and its
components when made from unplasticized poly(vinyl chloride) (PVC-U). The piping system is
intended to be used for soil and waste discharge.
For material and components, requirements and test methods are specified in EN 1329-1. This
standard also covers characteristics for fitness for purpose (mainly for joints). Recommended practice
for installation is given in ENV 13801.
This Part of EN 1329 covers procedures and recommendations for the assessment of conformity of
materials, components, joints and assemblies and is intended to be used by certification bodies,
inspection bodies, testing laboratories and manufacturers.

---------------------- Page: 6 ----------------------

SIST ENV 1329-2:2002
Page 5
ENV 1329-2:2001
1  Scope
This European Prestandard gives guidance for the assessment of conformity to be included in the
manufacturer’s quality plan as part of the quality system.
This prestandard includes :
a) Requirements for materials, components, joints and assemblies given in EN 1329-1:1999;
b) Requirements for the manufacturer’s quality system ;
NOTE 1  It is recommended that the quality system conforms to EN ISO 9001, as applicable.
c) Definitions and procedures to be applied if third party certification is involved.
NOTE 2 If third party certification is involved, it is recommended that the certification body is accredited
to EN 45011 or EN 45012, as applicable.
This Part of EN 1329 is applicable to piping systems made from unplasticized poly(vinyl chloride)
(PVC-U) in the field of soil and waste discharge systems (low and high temperature) inside buildings
(application area code “B”) and for soil and waste discharge systems for both inside buildings and
buried in ground within the building structure (application area code “BD”). This is reflected in the
marking of products by “B” or “BD”.
2  Normative references
This European Prestandard incorporates by dated or undated reference, provisions from other
publications. These normative references are cited at the appropriate places in the text and the
publications are listed hereafter. For dated references, subsequent amendments to or revisions of any
of these publications apply to this European Prestandard only when incorporated in it by amendment
or revision. For undated references the latest edition of the publication referred to applies (including
amendments).
EN 1329-1:1999, Plastics piping systems for soil and waste discharge (low and high temperature)
within the building structure — Unplasticized poly(vinyl chloride) (PVC-U) — Part 1: Specifications
for pipes, fittings and the system.
ISO 2859-1, Sampling procedures for inspection by attributes — Part 1 : Sampling schemes indexed
by acceptable quality level (AQL) for lot-by-lot inspection.
3  Definitions, symbols and abbreviations
For the purposes of this European Prestandard, the definitions, symbols and abbreviations given in
EN 1329-1:1999, apply together with the following :
3.1  Definitions
3.1.1
certification body
impartial body, governmental or non-governmental, possessing the necessary competence and
responsibility to carry out certification of conformity according to given rules of procedure and
management
3.1.2
inspection body
impartial organization or company, approved by a certification body as possessing the necessary
competence to verify and/or to carry out initial type testing, audit testing and inspection of the
manufacturer’s factory production control in accordance with the relevant European Standard

---------------------- Page: 7 ----------------------

SIST ENV 1329-2:2002
Page 6
ENV 1329-2:2001
3.1.3
testing laboratory
laboratory which measures, tests, calibrates or otherwise determines the characteristics of the
performance of materials and products
3.1.4
quality system
organizational structure, responsibilities, procedures, processes and resources for implementing
quality management (see EN ISO 8402)
3.1.5
quality plan
document setting out the specific quality practices, resources and sequence of activities relevant to a
particular product or range of products
3.1.6
type testing (TT)
tests performed to prove that the material, component, joint or assembly is capable of conforming to
the requirements given in the relevant standard
3.1.6.1
preliminary type testing (PTT)
type testing carried out by or on behalf of the manufacturer
3.1.6.2
initial type testing (ITT)
type testing carried out by, or on behalf of a certification body for certification purposes
3.1.7
batch release test (BRT)
test performed by the manufacturer on a batch of components which has to be satisfactorily completed
before the batch can be released
3.1.8
process verification test (PVT)
test performed by the manufacturer on materials, components, joints or assemblies at specified
intervals to confirm that the process continues to be capable of producing components conforming to
the requirements given in the relevant standard
NOTE Such tests are not required to release batches of components and are carried out as a
measure of process control.
3.1.9
audit test (AT)
test performed by, or on behalf of a certification body to confirm that the material, component, joint or
assembly continues to conform with the requirements given in a System Standard and to provide
information to assess the effectiveness of the quality system
3.1.10
indirect test (IT)
test performed by the manufacturer different from that specified for that particular characteristic,
having verified its correlation with the specified test
3.1.11
witness testing (WT)
testing accepted by the certification body for initial type testing and/or audit testing, which is carried out
by, or on behalf of the manufacturer and supervised by a representative of the certification body,
qualified in testing
3.1.12
material
defined type of polymer or additive or constituent thereof

---------------------- Page: 8 ----------------------

SIST ENV 1329-2:2002
Page 7
ENV 1329-2:2001
3.1.13
compound (blend)
recipe which defines types of polymer, additives or constituents at specified dosage levels
3.1.14
material batch or compound batch
clearly identifiable quantity of a particular material or compound
3.1.15
production batch
clearly identifiable collection of units, manufactured consecutively under the same conditions, using
material or compound conforming to the same specification
3.1.16
lot
clearly identifiable sub-division of a batch for inspection purposes
3.1.17
sample
one or more units of product drawn from a batch or lot, selected at random without regard to quality
NOTE The number of units of product in the sample is the sample size.
3.1.18
inspection level
relationship between the lot or batch size and the sample size (see ISO 2859-1)
3.1.19
group
collection of similar components from which samples are selected for testing purposes
3.2  Abbreviations
NOTE For reasons of avoiding misunderstanding the following abbreviations are kept the same in
each languages. For the same reason the terms are given in the three languages.
AT E : audit test
F : essai d’audit
D : Überwachungsprüfung
BRT E : batch release test
F : essai de libération de campagne de fabrication
D : Freigabeprüfung einer Charge
IT E : indirect test
F : essai indirect
D : indirekte Prüfung
ITT E : initial type testing
F : essai de type initial
D : Erst-Typprüfung
PTT E : preliminary type testing
F : essai de type préliminaire
D : vorausgehende Typprüfung
PVT E : process verification test
F : essai de vérification du procédé de fabrication
D : Prozessüberprüfung

---------------------- Page: 9 ----------------------

SIST ENV 1329-2:2002
Page 8
ENV 1329-2:2001
TT E : type test
F : essai de type
D : Typprüfung
WT E : witness testing
F : essai témoin
D : Prüfung unter Aufsicht
4  Requirements
4.1  General
4.1.1  Materials, components, joints and assemblies shall conform to the requirements given in
EN 1329-1:1999.
4.1.2  Components and/or assemblies shall be produced by the manufacturer under a quality system
which includes a quality plan.
4.2  Testing and inspection
4.2.1  Material specification
For the purposes of this prestandard the material specification consists of a recipe/compound which
defines types of PVC and additives and their dosage levels.
The dosage level of ingredients of a material shall not exceed the tolerance bands given in Table 1. If
any level exceeds the dosage band or if a type is changed, this variation in formulation constitutes a
change in material.
The values of t
...