SIST EN 301 908-5 V4.2.1:2010
(Main)Electromagnetic compatibility and Radio spectrum Matters (ERM) - Base Stations (BS), Repeaters and User Equipment (UE) for IMT-2000 Third-Generation cellular networks - Part 5: Harmonized EN for IMT-2000, CDMA Multi-Carrier (cdma2000) and Evolved CDMA Multi-Carrier Ultra Mobile Broadband (UMB) (BS) covering the essential requirements of article 3.2 of the R&TTE Directive
Electromagnetic compatibility and Radio spectrum Matters (ERM) - Base Stations (BS), Repeaters and User Equipment (UE) for IMT-2000 Third-Generation cellular networks - Part 5: Harmonized EN for IMT-2000, CDMA Multi-Carrier (cdma2000) and Evolved CDMA Multi-Carrier Ultra Mobile Broadband (UMB) (BS) covering the essential requirements of article 3.2 of the R&TTE Directive
The present document applies to the following radio equipment types:
Base stations for IMT-2000 CDMA multi-carrier (cdma2000) and Evolved CDMA Multi-Carrier Ultra Mobile Broadband (UMB). These radio equipment types are capable of operating in all or any part of the frequency bands given in table 1-1.
The present document covers requirements for IMT-2000 CDMA multi-carrier (cdma2000) User Equipments and Evolved CDMA Multi-Carrier (UMB) User Equipment. Base stations for IMT-2000 CDMA multi-carrier (cdma2000) may support:
1) operation in cdma2000 spread spectrum systems as defined in 3GPP2 C.S0002-D [2], referred to herein as operation in Type 1 cdma2000 systems; or
2) operation in cdma2000 High Rate Packet Data Systems as defined in TIA-856 [7], referred to herein in Type 2 cdma2000 systems. The present document is intended to cover the provisions of Directive 1999/5/EC [i.2] (R&TTE Directive) article 3.2, which states that "[…] radio equipment shall be so constructed that it effectively uses the spectrum allocated to terrestrial/space radio communications and orbital resources so as to avoid harmful interference". In addition to the present document, other ENs that specify technical requirements in respect of essential requirements under other parts of article 3 of the R&TTE Directive [i.2] may apply to equipment within the scope of the present document.
Elektromagnetna združljivost in zadeve v zvezi z radijskim spektrom (ERM) - Bazne postaje (BS), ponavljalniki (repetitorji) in uporabniška oprema (UE) za celična omrežja tretje generacije IMT-2000 - 5. del: Harmonizirani EN za IMT-2000, CDMA z več nosilnimi frekvencami (“Multi-Carrier”) (CDMA2000) in razvito CDMA z več nosilnimi frekvencami (“Multi-Carrier”) pri ultra mobilni širokopasovnosti (BS), ki zajema bistvene zahteve člena 3.2 direktive R&TTE
Pričujoči dokument velja za naslednje vrste radijske opreme:
bazne postaje za IMT-2000 CDMA »Multi-carrier« (cdma2000) in razvito CDMA z več nosilnimi frekvencami »Multi-carrier« pri ultra mobilni širokopasovnosti (BS). Ti tipi radijske opreme so zmožni delovanja v vseh ali katerem koli delu frekvenčnega pasu, kot so navedeni v tabeli 1-1.
Pričujoči dokument zajema zahteve za IMT-2000 CDMA »Multi-carrier« (cdma2000) uporabniško opremo in razvito CDMA z več nosilnimi frekvencami »Multi-Carrier« (BS) uporabniško opremo. Bazne postaje za IMT-2000 CDMA »Multi-Carrier« (cdma2000)lahko podpirajo:
1) delovanje v cdma2000 sistemih s spektralnim razprševanjem, kot je določeno v 3GPP2C.S0002-D [2], v nadaljevanju: delovanje v cdma2000 sistemih tipa 1; ali
2) delovanje v cdma2000 sistemih z visokimi stopnjami podatkovnih paketov kot je določeno v TIA-856 [7], v nadaljevanju cdma2000 sistemi tipa 2. Pričujoči dokument je namenjen temu, da zajema določbe Direktive 1999/5/ES (direktive R&TTE) [i.2], člena 3.2, ki navaja, da » … je radijska oprema narejena tako, da učinkovito izrablja spekter, razporejen za prizemne/vesoljske radiokomunikacije in orbitalne vire, tako da ne pride do škodljivega motenja«. Poleg pričujočega dokumenta, se ostali EN, ki določajo tehnične zahteve v skladu z bistvenimi zahtevami v drugih delih člena 3 direktive R&TTE [i.2],lahko uporabljajo za opremo znotraj področja uporabe pričujočega dokumenta.
General Information
Buy Standard
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Electromagnetic compatibility and Radio spectrum Matters (ERM) - Base Stations (BS), Repeaters and User Equipment (UE) for IMT-2000 Third-Generation cellular networks - Part 5: Harmonized EN for IMT-2000, CDMA Multi-Carrier (cdma2000) and Evolved CDMA Multi-Carrier Ultra Mobile Broadband (UMB) (BS) covering the essential requirements of article 3.2 of the R&TTE Directive33.100.01Elektromagnetna združljivost na splošnoElectromagnetic compatibility in general33.060.99Druga oprema za radijske komunikacijeOther equipment for radiocommunicationsICS:Ta slovenski standard je istoveten z:EN 301 908-5 Version 4.2.1SIST EN 301 908-5 V4.2.1:2010en01-maj-2010SIST EN 301 908-5 V4.2.1:2010SLOVENSKI
STANDARD
SIST EN 301 908-5 V4.2.1:2010
ETSI EN 301 908-5 V4.2.1 (2010-03)Harmonized European Standard (Telecommunications series) Electromagnetic compatibilityand Radio spectrum Matters (ERM);Base Stations (BS), Repeaters and User Equipment (UE)for IMT-2000 Third-Generation cellular networks;Part 5: Harmonized EN for IMT-2000, CDMA Multi-Carrier (cdma2000)and Evolved CDMA Multi-Carrier Ultra Mobile Broadband (UMB) (BS)covering the essential requirementsof article 3.2 of the R&TTE Directive SIST EN 301 908-5 V4.2.1:2010
ETSI ETSI EN 301 908-5 V4.2.1 (2010-03) 2
Reference REN/ERM-TFES-005-5 Keywords 3G, 3GPP2, cdma2000, cellular, digital, IMT-2000, mobile, radio, regulation, UMTS ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00
Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C Association à but non lucratif enregistrée à la Sous-Préfecture de Grasse (06) N° 7803/88
Important notice Individual copies of the present document can be downloaded from: http://www.etsi.org The present document may be made available in more than one electronic version or in print. In any case of existing or perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF). In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at http://portal.etsi.org/tb/status/status.asp If you find errors in the present document, please send your comment to one of the following services: http://portal.etsi.org/chaircor/ETSI_support.asp Copyright Notification No part may be reproduced except as authorized by written permission. The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2010. All rights reserved.
DECTTM, PLUGTESTSTM, UMTSTM, TIPHONTM, the TIPHON logo and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. LTE™ is a Trade Mark of ETSI currently being registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association. SIST EN 301 908-5 V4.2.1:2010
ETSI ETSI EN 301 908-5 V4.2.1 (2010-03) 3 Contents Intellectual Property Rights . 6 Foreword . 6 Introduction . 7 1 Scope . 8 2 References . 8 2.1 Normative references . 9 2.2 Informative references . 9 3 Definitions, symbols and abbreviations . 10 3.1 Definitions . 10 3.2 Symbols . 18 3.3 Abbreviations . 22 4 Technical requirements specifications . 23 4.1 Environmental profile . 23 4.2 Conformance requirements . 23 4.2.1 Introduction. 23 4.2.2 Transmitter conducted spurious emissions . 23 4.2.2.1 Definition . 23 4.2.2.2 Limits . 24 4.2.2.3 Conformance . 26 4.2.3 Maximum output power . 26 4.2.3.1 Definition . 26 4.2.3.2 Limits . 26 4.2.3.2.1 Base stations operating in Type 1 cdma2000 systems . 26 4.2.3.2.2 Base stations operating in Type 2 cdma2000 systems . 26 4.2.3.3 Conformance . 27 4.2.4 Inter-Base Station transmitter intermodulation . 27 4.2.4.1 Definition . 27 4.2.4.2 Limits . 27 4.2.4.3 Conformance . 27 4.2.5 Receiver conducted spurious emissions . 28 4.2.5.1 Definition . 28 4.2.5.2 Limits . 28 4.2.5.3 Conformance . 28 4.2.6 Receiver blocking characteristics . 28 4.2.6.1 Definition . 28 4.2.6.2 Limits . 28 4.2.6.2.1 Base stations operating in Type 1 cdma2000 systems . 28 4.2.6.2.2 Base stations operating in Type 2 cdma2000 systems . 28 4.2.6.3 Conformance . 28 4.2.7 Intermodulation spurious response attenuation . 29 4.2.7.1 Definition . 29 4.2.7.2 Limits . 29 4.2.7.2.1 Base stations operating in Type 1 cdma2000 systems . 29 4.2.7.2.2 Base stations operating in Type 2 cdma2000 systems . 29 4.2.7.3 Conformance . 29 4.2.8 Adjacent channel selectivity . 29 4.2.8.1 Definition . 29 4.2.8.2 Limits . 29 4.2.8.2.1 Base stations operating in Type 1 cdma2000 systems . 29 4.2.8.2.2 Base stations operating in Type 2 cdma2000 systems . 29 4.2.8.3 Conformance . 29 5 Testing for compliance with technical requirements . 30 5.1 Conditions for testing . 30 SIST EN 301 908-5 V4.2.1:2010
ETSI ETSI EN 301 908-5 V4.2.1 (2010-03) 4 5.1.1 Introduction. 30 5.1.2 Standard equipment under test . 30 5.1.2.1 Basic equipment . 30 5.1.2.2 Ancillary equipment . 30 5.2 Interpretation of the measurement results . 30 5.3 Essential radio test suites . 30 5.3.1 Transmitter conducted spurious emissions . 31 5.3.1.1 Test procedure for Base Stations supporting operation in Type 1 cdma2000 systems . 31 5.3.1.2 Test procedure for Base Stations supporting operation in Type 2 cdma2000 systems . 31 5.3.2 Maximum output power . 32 5.3.2.1 Test procedure for Base Stations supporting operation in Type 1 cdma2000 systems . 32 5.3.2.2 Test procedure for Base Stations supporting operation in Type 2 cdma2000 systems . 32 5.3.3 Inter-Base Station transmitter intermodulation . 33 5.3.3.1 Test procedure for Base Stations supporting operation in Type 1 cdma2000 systems . 33 5.3.3.2 Test procedure for Base Stations supporting operation in Type 2 cdma2000 systems 2 . 33 5.3.4 Receiver conducted spurious emissions . 34 5.3.4.1 Test procedure for Base Stations supporting operation in Type 1 or Type 2 cdma2000 systems . 34 5.3.5 Receiver blocking characteristics . 35 5.3.5.1 Test procedure for Base Stations supporting operation in Type 1 cdma2000 systems . 35 5.3.5.2 Test procedure for Base Stations supporting operation in Type 2 cdma2000 systems . 36 5.3.6 Intermodulation spurious response attenuation . 36 5.3.6.1 Test procedure for Base Stations supporting operation in Type 1 cdma2000 systems . 36 5.3.6.2 Test procedure for Base Stations supporting operation in Type 2 cdma2000 systems . 37 5.3.7 Adjacent channel selectivity . 37 5.3.7.1 Test procedure for Base Stations supporting operation in Type 1 cdma2000 systems . 37 5.3.7.2 Test procedure for Base Stations supporting operation in Type 2 cdma2000 systems . 38 Annex A (normative): HS Requirements and conformance Test specifications Table (HS-RTT) . 39 Annex B (normative): Base station Configurations . 41 B.1 Receiver diversity . 41 B.2 Duplexers . 41 B.3 Power supply options . 41 B.4 Ancillary RF amplifiers . 42 B.5 BS using antenna arrays . 42 B.5.1 Receiver tests . 43 B.5.2 Transmitter tests . 43 Annex C (informative): Environmental profile and standard test conditions . 44 C.1 Introduction . 44 C.2 CDMA environmental requirements . 44 C.2.1 Temperature and power supply voltage . 44 C.2.1.1 Definition . 44 C.2.1.2 Method of measurement . 44 C.2.1.3 Minimum standard . 45 C.2.2 High humidity . 45 C.2.2.1 Definition . 45 C.2.2.2 Method of measurement . 45 C.2.2.3 Minimum standard . 45 C.3 Standard test conditions. 45 C.3.1 Standard environmental test conditions . 45 C.3.2 Standard conditions for the primary power supply . 46 C.3.2.1 General . 46 C.3.2.2 Standard DC test voltage from accumulator batteries . 46 C.3.2.3 Standard AC voltage and frequency . 46 SIST EN 301 908-5 V4.2.1:2010
ETSI ETSI EN 301 908-5 V4.2.1 (2010-03) 5 Annex D (informative): The EN title in the official languages . 47 Annex E (informative): Bibliography . 48 History . 49
SIST EN 301 908-5 V4.2.1:2010
ETSI ETSI EN 301 908-5 V4.2.1 (2010-03) 6 Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (http://webapp.etsi.org/IPR/home.asp). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This Harmonized European Standard (Telecommunications series) has been produced by ETSI Technical Committee Electromagnetic compatibility and Radio spectrum Matters (ERM). The present document has been produced by ETSI in response to a mandate from the European Commission issued under Council Directive 98/34/EC [i.1] (as amended) laying down a procedure for the provision of information in the field of technical standards and regulations. The present document is intended to become a Harmonized Standard, the reference of which will be published in the Official Journal of the European Communities referencing the Directive 1999/5/EC [i.2] of the European Parliament and of the Council of 9 March 1999 on radio equipment and telecommunications terminal equipment and the mutual recognition of their conformity ("the R&TTE Directive"). Technical specifications relevant to Directive 1999/5/EC [i.2] are given in annex A. The present document is part 5 of a multi-part deliverable covering the Base Stations (BS), Repeaters and User Equipment (UE) for IMT-2000 Third-Generation cellular networks, as identified below: Part 1: "Harmonized EN for IMT-2000, introduction and common requirements, covering the essential requirements of article 3.2 of the R&TTE Directive"; Part 2: "Harmonized EN for IMT-2000, CDMA Direct Spread (UTRA FDD and E-UTRA FDD) (UE) covering the essential requirements of article 3.2 of the R&TTE Directive"; Part 3: "Harmonized EN for IMT-2000, CDMA Direct Spread (UTRA FDD and E-UTRA FDD) (BS) covering the essential requirements of article 3.2 of the R&TTE Directive"; Part 4: "Harmonized EN for IMT-2000, CDMA Multi-Carrier (cdma2000) and Evolved CDMA Multi-Carrier Ultra Mobile Broadband (UMB) (UE) covering the essential requirements of article 3.2 of the R&TTE Directive"; Part 5: "Harmonized EN for IMT-2000, CDMA Multi-Carrier (cdma2000) and Evolved CDMA Multi-Carrier Ultra Mobile Broadband (UMB) (BS) covering the essential requirements of article 3.2 of the R&TTE Directive"; Part 6: "Harmonized EN for IMT-2000, CDMA TDD (UTRA TDD and E-UTRA TDD) (UE) covering the essential requirements of article 3.2 of the R&TTE Directive"; Part 7: "Harmonized EN for IMT-2000, CDMA TDD (UTRA TDD and E-UTRA TDD) (BS) covering the essential requirements of article 3.2 of the R&TTE Directive"; Part 8: "Harmonized EN for IMT-2000, TDMA Single-Carrier (UWC 136) (UE) covering essential requirements of article 3.2 of the R&TTE Directive"; Part 9: "Harmonized EN for IMT-2000, TDMA Single-Carrier (UWC 136) (BS) covering essential requirements of article 3.2 of the R&TTE Directive"; SIST EN 301 908-5 V4.2.1:2010
ETSI ETSI EN 301 908-5 V4.2.1 (2010-03) 7 Part 10: "Harmonized EN for IMT-2000, FDMA/TDMA (DECT) covering essential requirements of article 3.2 of the R&TTE Directive"; Part 11: "Harmonized EN for IMT-2000, CDMA Direct Spread (UTRA FDD and E-UTRA FDD) (Repeaters) covering the essential requirements of article 3.2 of the R&TTE Directive"; Part 12: "Harmonized EN for IMT-2000, CDMA Multi-Carrier (cdma2000) (Repeaters) covering the essential requirements of article 3.2 of the R&TTE Directive"; Part 13: "Harmonized EN for IMT-2000, Evolved Universal Terrestrial Radio Access (E-UTRA) (UE) covering the essential requirements of article 3.2 of the R&TTE Directive"; Part 14: "Harmonized EN for IMT-2000, Evolved Universal Terrestrial Radio Access (E-UTRA) (BS) covering the essential requirements of article 3.2 of the R&TTE Directive";
Part 15: "Harmonized EN for IMT-2000, Evolved Universal Terrestrial Radio Access (E-UTRA) (FDD Repeaters) covering the essential requirements of article 3.2 of the R&TTE Directive"; Part 16: "Harmonized EN for IMT-2000, Evolved CDMA Multi-Carrier Ultra Mobile Broadband (UMB) (UE) covering the essential requirements of article 3.2 of the R&TTE Directive"; Part 17: "Harmonized EN for IMT-2000, Evolved CDMA Multi-Carrier Ultra Mobile Broadband (UMB) (BS) covering the essential requirements of article 3.2 of the R&TTE Directive".
National transposition dates Date of adoption of this EN: 19 February 2010 Date of latest announcement of this EN (doa): 31 May 2010 Date of latest publication of new National Standard or endorsement of this EN (dop/e):
30 November 2010 Date of withdrawal of any conflicting National Standard (dow): 30 November 2011
Introduction The present document is part of a set of standards developed by ETSI and is designed to fit in a modular structure to cover all radio and telecommunications terminal equipment within the scope of the R&TTE Directive [i.2]. The modular structure is shown in EG 201 399 [i.3]. SIST EN 301 908-5 V4.2.1:2010
ETSI ETSI EN 301 908-5 V4.2.1 (2010-03) 8 1 Scope The present document applies to the following radio equipment types: • Base stations for IMT-2000 CDMA multi-carrier (cdma2000) and Evolved CDMA Multi-Carrier Ultra Mobile Broadband (UMB). These radio equipment types are capable of operating in all or any part of the frequency bands given in table 1-1. Table 1-1: CDMA multi-carrier Base Station operating bands Band Class (BC) Direction of transmission CDMA multi-carrier Base Station operating bands 6 Transmit 2 110 MHz to 2 170 MHz Receive 1 920 MHz to 1 980 MHz 8 Transmit 1 805 MHz to 1 880 MHz Receive 1 710 MHz to 1 785 MHz 9 Transmit 925 MHz to 960 MHz Receive 880 MHz to 915 MHz 13 Transmit 2 620 MHz to 2 690 MHz Receive 2 500 MHz to 2 570 MHz
The present document covers requirements for IMT-2000 CDMA multi-carrier (cdma2000) User Equipments and Evolved CDMA Multi-Carrier (UMB) User Equipment. Base stations for IMT-2000 CDMA multi-carrier (cdma2000) may support: 1) operation in cdma2000 spread spectrum systems as defined in 3GPP2 C.S0002-D [2], referred to herein as operation in Type 1 cdma2000 systems; or 2) operation in cdma2000 High Rate Packet Data Systems as defined in TIA-856 [7], referred to herein in Type 2 cdma2000 systems. The present document is intended to cover the provisions of Directive 1999/5/EC [i.2] (R&TTE Directive) article 3.2, which states that "[…] radio equipment shall be so constructed that it effectively uses the spectrum allocated to terrestrial/space radio communications and orbital resources so as to avoid harmful interference". In addition to the present document, other ENs that specify technical requirements in respect of essential requirements under other parts of article 3 of the R&TTE Directive [i.2] may apply to equipment within the scope of the present document. NOTE: A list of such ENs is included on the web site http://www.newapproach.org/. 2 References References are either specific (identified by date of publication and/or edition number or version number) or non-specific. • For a specific reference, subsequent revisions do not apply. • Non-specific reference may be made only to a complete document or a part thereof and only in the following cases:
- if it is accepted that it will be possible to use all future changes of the referenced document for the purposes of the referring document;
- for informative references. Referenced documents which are not found to be publicly available in the expected location might be found at http://docbox.etsi.org/Reference. SIST EN 301 908-5 V4.2.1:2010
ETSI ETSI EN 301 908-5 V4.2.1 (2010-03) 9 NOTE: While any hyperlinks included in this clause were valid at the time of publication ETSI cannot guarantee their long term validity. 2.1 Normative references The following referenced documents are indispensable for the application of the present document. For dated references, only the edition cited applies. For non-specific references, the latest edition of the referenced document (including any amendments) applies. [1] ANSI/TIA-97-F-1 (June 2006): "Recommended Minimum Performance Standards for cdma2000 Spread Spectrum Base Stations - Addendum 1". [2] 3GPP2 C.S0002-D V2.0 (September 2005): "Physical Layer Standard for cdma2000 Spread Spectrum Systems Revision D". NOTE: Available at: http://www.3gpp2.org/Public_html/Specs/C.S0002-D_v2.0_051006.pdf. [3] ANSI/TIA-98-F-1 (June 2006): "Recommended Minimum Performance Standards for cdma2000 Spread Spectrum Mobile Stations - Addendum". [4] TIA/EIA-126-D (June 2001): "Loopback Service Options Standard (LSO) for cdma Spread Spectrum Systems". [5] TIA-870-A (March 2005): "Test Data Service Option (TDSO) for cdma2000 Spread Spectrum Systems - Revision A". [6] TIA/EIA/IS-871 (April 2001): "Markov Service Option (MSO) for cdma2000 Spread Spectrum Systems". [7] TIA-856-B-1 (October 2007): "cdma2000 High Rate Packet Data Air Interface Specification". [8] 3GPP2 C.S0032-B V1.0 (May 2008): "Recommended Minimum Performance Standards for cdma2000 High Rate Packet Data Access Network". NOTE: Available at: http://www.3gpp2.org/Public_html/specs/C.S0032-B_v1.0_080519.pdf. [9] 3GPP2 C.S0029-B V1.0 (March 2008): "Test Application Specification (TAS) for High Rate Packet Data Air Interface". NOTE: Available at: http://www.3gpp2.org/Public_html/specs/C.S0029-B_v1.0_080409.pdf. [10] ETSI EN 301 908-1 (V4.1.2): "Electromagnetic compatibility and Radio s
...
ETSI EN 301 908-5 V4.2.1 (2010-03)
Harmonized European Standard (Telecommunications series)
Electromagnetic compatibility
and Radio spectrum Matters (ERM);
Base Stations (BS), Repeaters and User Equipment (UE)
for IMT-2000 Third-Generation cellular networks;
Part 5: Harmonized EN for IMT-2000, CDMA Multi-Carrier (cdma2000)
and Evolved CDMA Multi-Carrier Ultra Mobile Broadband (UMB) (BS)
covering the essential requirements
of article 3.2 of the R&TTE Directive
---------------------- Page: 1 ----------------------
2 ETSI EN 301 908-5 V4.2.1 (2010-03)
Reference
REN/ERM-TFES-005-5
Keywords
3G, 3GPP2, cdma2000, cellular, digital, IMT-
2000, mobile, radio, regulation, UMTS
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
Individual copies of the present document can be downloaded from:
http://www.etsi.org
The present document may be made available in more than one electronic version or in print. In any case of existing or
perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF).
In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive
within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
http://portal.etsi.org/chaircor/ETSI_support.asp
Copyright Notification
No part may be reproduced except as authorized by written permission.
The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2010.
All rights reserved.
TM TM TM TM
DECT , PLUGTESTS , UMTS , TIPHON , the TIPHON logo and the ETSI logo are Trade Marks of ETSI registered
for the benefit of its Members.
TM
3GPP is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners.
LTE™ is a Trade Mark of ETSI currently being registered
for the benefit of its Members and of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3 ETSI EN 301 908-5 V4.2.1 (2010-03)
Contents
Intellectual Property Rights . 6
Foreword . 6
Introduction . 7
1 Scope . 8
2 References . 8
2.1 Normative references . 9
2.2 Informative references . 9
3 Definitions, symbols and abbreviations . 10
3.1 Definitions . 10
3.2 Symbols . 18
3.3 Abbreviations . 22
4 Technical requirements specifications . 23
4.1 Environmental profile . 23
4.2 Conformance requirements . 23
4.2.1 Introduction. 23
4.2.2 Transmitter conducted spurious emissions . 23
4.2.2.1 Definition . 23
4.2.2.2 Limits . 24
4.2.2.3 Conformance . 26
4.2.3 Maximum output power . 26
4.2.3.1 Definition . 26
4.2.3.2 Limits . 26
4.2.3.2.1 Base stations operating in Type 1 cdma2000 systems . 26
4.2.3.2.2 Base stations operating in Type 2 cdma2000 systems . 26
4.2.3.3 Conformance . 27
4.2.4 Inter-Base Station transmitter intermodulation . 27
4.2.4.1 Definition . 27
4.2.4.2 Limits . 27
4.2.4.3 Conformance . 27
4.2.5 Receiver conducted spurious emissions . 28
4.2.5.1 Definition . 28
4.2.5.2 Limits . 28
4.2.5.3 Conformance . 28
4.2.6 Receiver blocking characteristics . 28
4.2.6.1 Definition . 28
4.2.6.2 Limits . 28
4.2.6.2.1 Base stations operating in Type 1 cdma2000 systems . 28
4.2.6.2.2 Base stations operating in Type 2 cdma2000 systems . 28
4.2.6.3 Conformance . 28
4.2.7 Intermodulation spurious response attenuation . 29
4.2.7.1 Definition . 29
4.2.7.2 Limits . 29
4.2.7.2.1 Base stations operating in Type 1 cdma2000 systems . 29
4.2.7.2.2 Base stations operating in Type 2 cdma2000 systems . 29
4.2.7.3 Conformance . 29
4.2.8 Adjacent channel selectivity . 29
4.2.8.1 Definition . 29
4.2.8.2 Limits . 29
4.2.8.2.1 Base stations operating in Type 1 cdma2000 systems . 29
4.2.8.2.2 Base stations operating in Type 2 cdma2000 systems . 29
4.2.8.3 Conformance . 29
5 Testing for compliance with technical requirements . 30
5.1 Conditions for testing . 30
ETSI
---------------------- Page: 3 ----------------------
4 ETSI EN 301 908-5 V4.2.1 (2010-03)
5.1.1 Introduction. 30
5.1.2 Standard equipment under test . 30
5.1.2.1 Basic equipment . 30
5.1.2.2 Ancillary equipment . 30
5.2 Interpretation of the measurement results . 30
5.3 Essential radio test suites . 30
5.3.1 Transmitter conducted spurious emissions . 31
5.3.1.1 Test procedure for Base Stations supporting operation in Type 1 cdma2000 systems . 31
5.3.1.2 Test procedure for Base Stations supporting operation in Type 2 cdma2000 systems . 31
5.3.2 Maximum output power . 32
5.3.2.1 Test procedure for Base Stations supporting operation in Type 1 cdma2000 systems . 32
5.3.2.2 Test procedure for Base Stations supporting operation in Type 2 cdma2000 systems . 32
5.3.3 Inter-Base Station transmitter intermodulation . 33
5.3.3.1 Test procedure for Base Stations supporting operation in Type 1 cdma2000 systems . 33
5.3.3.2 Test procedure for Base Stations supporting operation in Type 2 cdma2000 systems 2 . 33
5.3.4 Receiver conducted spurious emissions . 34
5.3.4.1 Test procedure for Base Stations supporting operation in Type 1 or Type 2 cdma2000 systems . 34
5.3.5 Receiver blocking characteristics . 35
5.3.5.1 Test procedure for Base Stations supporting operation in Type 1 cdma2000 systems . 35
5.3.5.2 Test procedure for Base Stations supporting operation in Type 2 cdma2000 systems . 36
5.3.6 Intermodulation spurious response attenuation . 36
5.3.6.1 Test procedure for Base Stations supporting operation in Type 1 cdma2000 systems . 36
5.3.6.2 Test procedure for Base Stations supporting operation in Type 2 cdma2000 systems . 37
5.3.7 Adjacent channel selectivity . 37
5.3.7.1 Test procedure for Base Stations supporting operation in Type 1 cdma2000 systems . 37
5.3.7.2 Test procedure for Base Stations supporting operation in Type 2 cdma2000 systems . 38
Annex A (normative): HS Requirements and conformance Test specifications Table
(HS-RTT) . 39
Annex B (normative): Base station Configurations . 41
B.1 Receiver diversity . 41
B.2 Duplexers . 41
B.3 Power supply options . 41
B.4 Ancillary RF amplifiers . 42
B.5 BS using antenna arrays . 42
B.5.1 Receiver tests . 43
B.5.2 Transmitter tests . 43
Annex C (informative): Environmental profile and standard test conditions . 44
C.1 Introduction . 44
C.2 CDMA environmental requirements . 44
C.2.1 Temperature and power supply voltage . 44
C.2.1.1 Definition . 44
C.2.1.2 Method of measurement . 44
C.2.1.3 Minimum standard . 45
C.2.2 High humidity . 45
C.2.2.1 Definition . 45
C.2.2.2 Method of measurement . 45
C.2.2.3 Minimum standard . 45
C.3 Standard test conditions. 45
C.3.1 Standard environmental test conditions . 45
C.3.2 Standard conditions for the primary power supply . 46
C.3.2.1 General . 46
C.3.2.2 Standard DC test voltage from accumulator batteries . 46
C.3.2.3 Standard AC voltage and frequency . 46
ETSI
---------------------- Page: 4 ----------------------
5 ETSI EN 301 908-5 V4.2.1 (2010-03)
Annex D (informative): The EN title in the official languages . 47
Annex E (informative): Bibliography . 48
History . 49
ETSI
---------------------- Page: 5 ----------------------
6 ETSI EN 301 908-5 V4.2.1 (2010-03)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (http://webapp.etsi.org/IPR/home.asp).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This Harmonized European Standard (Telecommunications series) has been produced by ETSI Technical Committee
Electromagnetic compatibility and Radio spectrum Matters (ERM).
The present document has been produced by ETSI in response to a mandate from the European Commission issued
under Council Directive 98/34/EC [i.1] (as amended) laying down a procedure for the provision of information in the
field of technical standards and regulations.
The present document is intended to become a Harmonized Standard, the reference of which will be published in the
Official Journal of the European Communities referencing the Directive 1999/5/EC [i.2] of the European Parliament
and of the Council of 9 March 1999 on radio equipment and telecommunications terminal equipment and the mutual
recognition of their conformity ("the R&TTE Directive").
Technical specifications relevant to Directive 1999/5/EC [i.2] are given in annex A.
The present document is part 5 of a multi-part deliverable covering the Base Stations (BS), Repeaters and User
Equipment (UE) for IMT-2000 Third-Generation cellular networks, as identified below:
Part 1: "Harmonized EN for IMT-2000, introduction and common requirements, covering the essential
requirements of article 3.2 of the R&TTE Directive";
Part 2: "Harmonized EN for IMT-2000, CDMA Direct Spread (UTRA FDD and E-UTRA FDD) (UE) covering
the essential requirements of article 3.2 of the R&TTE Directive";
Part 3: "Harmonized EN for IMT-2000, CDMA Direct Spread (UTRA FDD and E-UTRA FDD) (BS) covering
the essential requirements of article 3.2 of the R&TTE Directive";
Part 4: "Harmonized EN for IMT-2000, CDMA Multi-Carrier (cdma2000) and Evolved CDMA Multi-Carrier
Ultra Mobile Broadband (UMB) (UE) covering the essential requirements of article 3.2 of the R&TTE
Directive";
Part 5: "Harmonized EN for IMT-2000, CDMA Multi-Carrier (cdma2000) and Evolved CDMA
Multi-Carrier Ultra Mobile Broadband (UMB) (BS) covering the essential requirements of
article 3.2 of the R&TTE Directive";
Part 6: "Harmonized EN for IMT-2000, CDMA TDD (UTRA TDD and E-UTRA TDD) (UE) covering the
essential requirements of article 3.2 of the R&TTE Directive";
Part 7: "Harmonized EN for IMT-2000, CDMA TDD (UTRA TDD and E-UTRA TDD) (BS) covering the
essential requirements of article 3.2 of the R&TTE Directive";
Part 8: "Harmonized EN for IMT-2000, TDMA Single-Carrier (UWC 136) (UE) covering essential requirements
of article 3.2 of the R&TTE Directive";
Part 9: "Harmonized EN for IMT-2000, TDMA Single-Carrier (UWC 136) (BS) covering essential requirements
of article 3.2 of the R&TTE Directive";
ETSI
---------------------- Page: 6 ----------------------
7 ETSI EN 301 908-5 V4.2.1 (2010-03)
Part 10: "Harmonized EN for IMT-2000, FDMA/TDMA (DECT) covering essential requirements of article 3.2 of
the R&TTE Directive";
Part 11: "Harmonized EN for IMT-2000, CDMA Direct Spread (UTRA FDD and E-UTRA FDD) (Repeaters)
covering the essential requirements of article 3.2 of the R&TTE Directive";
Part 12: "Harmonized EN for IMT-2000, CDMA Multi-Carrier (cdma2000) (Repeaters) covering the essential
requirements of article 3.2 of the R&TTE Directive";
Part 13: "Harmonized EN for IMT-2000, Evolved Universal Terrestrial Radio Access (E-UTRA) (UE) covering
the essential requirements of article 3.2 of the R&TTE Directive";
Part 14: "Harmonized EN for IMT-2000, Evolved Universal Terrestrial Radio Access (E-UTRA) (BS) covering
the essential requirements of article 3.2 of the R&TTE Directive";
Part 15: "Harmonized EN for IMT-2000, Evolved Universal Terrestrial Radio Access (E-UTRA) (FDD
Repeaters) covering the essential requirements of article 3.2 of the R&TTE Directive";
Part 16: "Harmonized EN for IMT-2000, Evolved CDMA Multi-Carrier Ultra Mobile Broadband (UMB) (UE)
covering the essential requirements of article 3.2 of the R&TTE Directive";
Part 17: "Harmonized EN for IMT-2000, Evolved CDMA Multi-Carrier Ultra Mobile Broadband (UMB) (BS)
covering the essential requirements of article 3.2 of the R&TTE Directive".
National transposition dates
Date of adoption of this EN: 19 February 2010
Date of latest announcement of this EN (doa): 31 May 2010
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 30 November 2010
Date of withdrawal of any conflicting National Standard (dow): 30 November 2011
Introduction
The present document is part of a set of standards developed by ETSI and is designed to fit in a modular structure to
cover all radio and telecommunications terminal equipment within the scope of the R&TTE Directive [i.2]. The
modular structure is shown in EG 201 399 [i.3].
ETSI
---------------------- Page: 7 ----------------------
8 ETSI EN 301 908-5 V4.2.1 (2010-03)
1 Scope
The present document applies to the following radio equipment types:
• Base stations for IMT-2000 CDMA multi-carrier (cdma2000) and Evolved CDMA Multi-Carrier Ultra Mobile
Broadband (UMB).
These radio equipment types are capable of operating in all or any part of the frequency bands given in table 1-1.
Table 1-1: CDMA multi-carrier Base Station operating bands
Band Class (BC) Direction of transmission CDMA multi-carrier Base Station
operating bands
Transmit 2 110 MHz to 2 170 MHz
6
Receive 1 920 MHz to 1 980 MHz
Transmit 1 805 MHz to 1 880 MHz
8
Receive 1 710 MHz to 1 785 MHz
Transmit 925 MHz to 960 MHz
9
Receive 880 MHz to 915 MHz
Transmit 2 620 MHz to 2 690 MHz
13
Receive 2 500 MHz to 2 570 MHz
The present document covers requirements for IMT-2000 CDMA multi-carrier (cdma2000) User Equipments and
Evolved CDMA Multi-Carrier (UMB) User Equipment.
Base stations for IMT-2000 CDMA multi-carrier (cdma2000) may support:
1) operation in cdma2000 spread spectrum systems as defined in 3GPP2 C.S0002-D [2], referred to herein as
operation in Type 1 cdma2000 systems; or
2) operation in cdma2000 High Rate Packet Data Systems as defined in TIA-856 [7], referred to herein in Type 2
cdma2000 systems.
The present document is intended to cover the provisions of Directive 1999/5/EC [i.2] (R&TTE Directive) article 3.2,
which states that "[…] radio equipment shall be so constructed that it effectively uses the spectrum allocated to
terrestrial/space radio communications and orbital resources so as to avoid harmful interference".
In addition to the present document, other ENs that specify technical requirements in respect of essential requirements
under other parts of article 3 of the R&TTE Directive [i.2] may apply to equipment within the scope of the present
document.
NOTE: A list of such ENs is included on the web site http://www.newapproach.org/.
2 References
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific.
• For a specific reference, subsequent revisions do not apply.
• Non-specific reference may be made only to a complete document or a part thereof and only in the following
cases:
- if it is accepted that it will be possible to use all future changes of the referenced document for the
purposes of the referring document;
- for informative references.
Referenced documents which are not found to be publicly available in the expected location might be found at
http://docbox.etsi.org/Reference.
ETSI
---------------------- Page: 8 ----------------------
9 ETSI EN 301 908-5 V4.2.1 (2010-03)
NOTE: While any hyperlinks included in this clause were valid at the time of publication ETSI cannot guarantee
their long term validity.
2.1 Normative references
The following referenced documents are indispensable for the application of the present document. For dated
references, only the edition cited applies. For non-specific references, the latest edition of the referenced document
(including any amendments) applies.
[1] ANSI/TIA-97-F-1 (June 2006): "Recommended Minimum Performance Standards for cdma2000
Spread Spectrum Base Stations - Addendum 1".
[2] 3GPP2 C.S0002-D V2.0 (September 2005): "Physical Layer Standard for cdma2000 Spread
Spectrum Systems Revision D".
NOTE: Available at: http://www.3gpp2.org/Public_html/Specs/C.S0002-D_v2.0_051006.pdf.
[3] ANSI/TIA-98-F-1 (June 2006): "Recommended Minimum Performance Standards for cdma2000
Spread Spectrum Mobile Stations - Addendum".
[4] TIA/EIA-126-D (June 2001): "Loopback Service Options Standard (LSO) for cdma Spread
Spectrum Systems".
[5] TIA-870-A (March 2005): "Test Data Service Option (TDSO) for cdma2000 Spread Spectrum
Systems - Revision A".
[6] TIA/EIA/IS-871 (April 2001): "Markov Service Option (MSO) for cdma2000 Spread Spectrum
Systems".
[7] TIA-856-B-1 (October 2007): "cdma2000 High Rate Packet Data Air Interface Specification".
[8] 3GPP2 C.S0032-B V1.0 (May 2008): "Recommended Minimum Performance Standards for
cdma2000 High Rate Packet Data Access Network".
NOTE: Available at: http://www.3gpp2.org/Public_html/specs/C.S0032-B_v1.0_080519.pdf.
[9] 3GPP2 C.S0029-B V1.0 (March 2008): "Test Application Specification (TAS) for High Rate
Packet Data Air Interface".
NOTE: Available at: http://www.3gpp2.org/Public_html/specs/C.S0029-B_v1.0_080409.pdf.
[10] ETSI EN 301 908-1 (V4.1.2): "Electromagnetic compatibility and Radio spectrum Matters (ERM);
Base Stations (BS), Repeaters and User Equipment (UE) for IMT-2000 Third-Generation cellular
networks; Part 1: Harmonized EN for IMT-2000, introduction and common requirements,
covering the essential requirements of article 3.2 of the R&TTE Directive".
[11] ETSI EN 301 908-17 (V4
...
Final draft ETSI EN 301 908-5 V4.1.2 (2009-12)
Harmonized European Standard (Telecommunications series)
Electromagnetic compatibility
and Radio spectrum Matters (ERM);
Base Stations (BS), Repeaters and User Equipment (UE)
for IMT-2000 Third-Generation cellular networks;
Part 5: Harmonized EN for IMT-2000, CDMA Multi-Carrier (cdma2000)
and Evolved CDMA Multi-Carrier Ultra Mobile Broadband (UMB) (BS)
covering the essential requirements
of article 3.2 of the R&TTE Directive
---------------------- Page: 1 ----------------------
2 Final draft ETSI EN 301 908-5 V4.1.2 (2009-12)
Reference
REN/ERM-TFES-005-5
Keywords
3G, 3GPP2, cdma2000, cellular, digital,
IMT-2000, mobile, radio, regulation, UMTS
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
Individual copies of the present document can be downloaded from:
http://www.etsi.org
The present document may be made available in more than one electronic version or in print. In any case of existing or
perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF).
In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive
within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
http://portal.etsi.org/chaircor/ETSI_support.asp
Copyright Notification
No part may be reproduced except as authorized by written permission.
The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2009.
All rights reserved.
TM TM TM TM
DECT , PLUGTESTS , UMTS , TIPHON , the TIPHON logo and the ETSI logo are Trade Marks of ETSI registered
for the benefit of its Members.
TM
3GPP is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners.
LTE™ is a Trade Mark of ETSI currently being registered
for the benefit of its Members and of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3 Final draft ETSI EN 301 908-5 V4.1.2 (2009-12)
Contents
Intellectual Property Rights . 6
Foreword . 6
Introduction . 7
1 Scope . 8
2 References . 8
2.1 Normative references . 9
2.2 Informative references . 9
3 Definitions, symbols and abbreviations . 10
3.1 Definitions . 10
3.2 Symbols . 18
3.3 Abbreviations . 22
4 Technical requirements specifications . 23
4.1 Environmental profile . 23
4.2 Conformance requirements . 23
4.2.1 Introduction. 23
4.2.2 Transmitter conducted spurious emissions . 23
4.2.2.1 Definition . 23
4.2.2.2 Limits . 24
4.2.2.3 Conformance . 26
4.2.3 Maximum output power . 26
4.2.3.1 Definition . 26
4.2.3.2 Limits . 26
4.2.3.2.1 Base stations operating in Type 1 cdma2000 systems . 26
4.2.3.2.2 Base stations operating in Type 2 cdma2000 systems . 26
4.2.3.3 Conformance . 27
4.2.4 Inter-Base Station transmitter intermodulation . 27
4.2.4.1 Definition . 27
4.2.4.2 Limits . 27
4.2.4.3 Conformance . 27
4.2.5 Receiver conducted spurious emissions . 28
4.2.5.1 Definition . 28
4.2.5.2 Limits . 28
4.2.5.3 Conformance . 28
4.2.6 Receiver blocking characteristics . 28
4.2.6.1 Definition . 28
4.2.6.2 Limits . 28
4.2.6.2.1 Base stations operating in Type 1 cdma2000 systems . 28
4.2.6.2.2 Base stations operating in Type 2 cdma2000 systems . 28
4.2.6.3 Conformance . 28
4.2.7 Intermodulation spurious response attenuation . 29
4.2.7.1 Definition . 29
4.2.7.2 Limits . 29
4.2.7.2.1 Base stations operating in Type 1 cdma2000 systems . 29
4.2.7.2.2 Base stations operating in Type 2 cdma2000 systems . 29
4.2.7.3 Conformance . 29
4.2.8 Adjacent channel selectivity . 29
4.2.8.1 Definition . 29
4.2.8.2 Limits . 29
4.2.8.2.1 Base stations operating in Type 1 cdma2000 systems . 29
4.2.8.2.2 Base stations operating in Type 2 cdma2000 systems . 29
4.2.8.3 Conformance . 29
5 Testing for compliance with technical requirements . 30
5.1 Conditions for testing . 30
ETSI
---------------------- Page: 3 ----------------------
4 Final draft ETSI EN 301 908-5 V4.1.2 (2009-12)
5.1.1 Introduction. 30
5.1.2 Standard equipment under test . 30
5.1.2.1 Basic equipment . 30
5.1.2.2 Ancillary equipment . 30
5.2 Interpretation of the measurement results . 30
5.3 Essential radio test suites . 30
5.3.1 Transmitter conducted spurious emissions . 31
5.3.1.1 Test procedure for Base Stations supporting operation in Type 1 cdma2000 systems . 31
5.3.1.2 Test procedure for Base Stations supporting operation in Type 2 cdma2000 systems . 31
5.3.2 Maximum output power . 32
5.3.2.1 Test procedure for Base Stations supporting operation in Type 1 cdma2000 systems . 32
5.3.2.2 Test procedure for Base Stations supporting operation in Type 2 cdma2000 systems . 32
5.3.3 Inter-Base Station transmitter intermodulation . 33
5.3.3.1 Test procedure for Base Stations supporting operation in Type 1 cdma2000 systems . 33
5.3.3.2 Test procedure for Base Stations supporting operation in Type 2 cdma2000 systems 2 . 33
5.3.4 Receiver conducted spurious emissions . 34
5.3.4.1 Test procedure for Base Stations supporting operation in Type 1 or Type 2 cdma2000 systems . 34
5.3.5 Receiver blocking characteristics . 35
5.3.5.1 Test procedure for Base Stations supporting operation in Type 1 cdma2000 systems . 35
5.3.5.2 Test procedure for Base Stations supporting operation in Type 2 cdma2000 systems . 36
5.3.6 Intermodulation spurious response attenuation . 36
5.3.6.1 Test procedure for Base Stations supporting operation in Type 1 cdma2000 systems . 36
5.3.6.2 Test procedure for Base Stations supporting operation in Type 2 cdma2000 systems . 37
5.3.7 Adjacent channel selectivity . 37
5.3.7.1 Test procedure for Base Stations supporting operation in Type 1 cdma2000 systems . 37
5.3.7.2 Test procedure for Base Stations supporting operation in Type 2 cdma2000 systems . 38
Annex A (normative): HS Requirements and conformance Test specifications Table
(HS-RTT) . 39
Annex B (normative): Base station Configurations . 41
B.1 Receiver diversity . 41
B.2 Duplexers . 41
B.3 Power supply options . 41
B.4 Ancillary RF amplifiers . 42
B.5 BS using antenna arrays . 42
B.5.1 Receiver tests . 43
B.5.2 Transmitter tests . 43
Annex C (informative): Environmental profile and standard test conditions . 44
C.1 Introduction . 44
C.2 CDMA environmental requirements . 44
C.2.1 Temperature and power supply voltage . 44
C.2.1.1 Definition . 44
C.2.1.2 Method of measurement . 44
C.2.1.3 Minimum standard . 45
C.2.2 High humidity . 45
C.2.2.1 Definition . 45
C.2.2.2 Method of measurement . 45
C.2.2.3 Minimum standard . 45
C.3 Standard test conditions. 45
C.3.1 Standard environmental test conditions . 45
C.3.2 Standard conditions for the primary power supply . 46
C.3.2.1 General . 46
C.3.2.2 Standard DC test voltage from accumulator batteries . 46
C.3.2.3 Standard AC voltage and frequency . 46
ETSI
---------------------- Page: 4 ----------------------
5 Final draft ETSI EN 301 908-5 V4.1.2 (2009-12)
Annex D (informative): The EN title in the official languages . 47
Annex E (informative): Bibliography . 48
History . 49
ETSI
---------------------- Page: 5 ----------------------
6 Final draft ETSI EN 301 908-5 V4.1.2 (2009-12)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (http://webapp.etsi.org/IPR/home.asp).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This Harmonized European Standard (Telecommunications series) has been produced by ETSI Technical Committee
Electromagnetic compatibility and Radio spectrum Matters (ERM), and is now submitted for the Vote phase of the
ETSI standards Two-step Approval Procedure.
The present document has been produced by ETSI in response to a mandate from the European Commission issued
under Council Directive 98/34/EC [i.1] (as amended) laying down a procedure for the provision of information in the
field of technical standards and regulations.
The present document is intended to become a Harmonized Standard, the reference of which will be published in the
Official Journal of the European Communities referencing the Directive 1999/5/EC [i.2] of the European Parliament
and of the Council of 9 March 1999 on radio equipment and telecommunications terminal equipment and the mutual
recognition of their conformity ("the R&TTE Directive").
Technical specifications relevant to Directive 1999/5/EC [i.2] are given in annex A.
The present document is part 5 of a multi-part deliverable covering the Base Stations (BS), Repeaters and User
Equipment (UE) for IMT-2000 Third-Generation cellular networks, as identified below:
Part 1: "Harmonized EN for IMT-2000, introduction and common requirements, covering the essential
requirements of article 3.2 of the R&TTE Directive";
Part 2: "Harmonized EN for IMT-2000, CDMA Direct Spread (UTRA FDD and E-UTRA FDD) (UE) covering
the essential requirements of article 3.2 of the R&TTE Directive";
Part 3: "Harmonized EN for IMT-2000, CDMA Direct Spread (UTRA FDD and E-UTRA FDD) (BS) covering
the essential requirements of article 3.2 of the R&TTE Directive";
Part 4: "Harmonized EN for IMT-2000, CDMA Multi-Carrier (cdma2000) and Evolved CDMA Multi-Carrier
Ultra Mobile Broadband (UMB) (UE) covering the essential requirements of article 3.2 of the R&TTE
Directive";
Part 5: "Harmonized EN for IMT-2000, CDMA Multi-Carrier (cdma2000) and Evolved CDMA
Multi-Carrier Ultra Mobile Broadband (UMB) (BS) covering the essential requirements of
article 3.2 of the R&TTE Directive";
Part 6: "Harmonized EN for IMT-2000, CDMA TDD (UTRA TDD and E-UTRA TDD) (UE) covering the
essential requirements of article 3.2 of the R&TTE Directive";
Part 7: "Harmonized EN for IMT-2000, CDMA TDD (UTRA TDD and E-UTRA TDD) (BS) covering the
essential requirements of article 3.2 of the R&TTE Directive";
Part 8: "Harmonized EN for IMT-2000, TDMA Single-Carrier (UWC 136) (UE) covering essential requirements
of article 3.2 of the R&TTE Directive";
Part 9: "Harmonized EN for IMT-2000, TDMA Single-Carrier (UWC 136) (BS) covering essential requirements
of article 3.2 of the R&TTE Directive";
ETSI
---------------------- Page: 6 ----------------------
7 Final draft ETSI EN 301 908-5 V4.1.2 (2009-12)
Part 10: "Harmonized EN for IMT-2000, FDMA/TDMA (DECT) covering essential requirements of article 3.2 of
the R&TTE Directive";
Part 11: "Harmonized EN for IMT-2000, CDMA Direct Spread (UTRA FDD and E-UTRA FDD) (Repeaters)
covering the essential requirements of article 3.2 of the R&TTE Directive";
Part 12: "Harmonized EN for IMT-2000, CDMA Multi-Carrier (cdma2000) (Repeaters) covering the essential
requirements of article 3.2 of the R&TTE Directive";
Part 13: "Harmonized EN for IMT-2000, Evolved Universal Terrestrial Radio Access (E-UTRA) (UE) covering
the essential requirements of article 3.2 of the R&TTE Directive";
Part 14: "Harmonized EN for IMT-2000, Evolved Universal Terrestrial Radio Access (E-UTRA) (BS) covering
the essential requirements of article 3.2 of the R&TTE Directive";
Part 15: "Harmonized EN for IMT-2000, Evolved Universal Terrestrial Radio Access (E-UTRA) (FDD
Repeaters) covering the essential requirements of article 3.2 of the R&TTE Directive";
Part 16: "Harmonized EN for IMT-2000, Evolved CDMA Multi-Carrier Ultra Mobile Broadband (UMB) (UE)
covering the essential requirements of article 3.2 of the R&TTE Directive";
Part 17: "Harmonized EN for IMT-2000, Evolved CDMA Multi-Carrier Ultra Mobile Broadband (UMB) (BS)
covering the essential requirements of article 3.2 of the R&TTE Directive".
Proposed national transposition dates
Date of latest announcement of this EN (doa): 3 months after ETSI publication
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 6 months after doa
Date of withdrawal of any conflicting National Standard (dow): 18 months after doa
Introduction
The present document is part of a set of standards developed by ETSI and is designed to fit in a modular structure to
cover all radio and telecommunications terminal equipment within the scope of the R&TTE Directive [i.2]. The
modular structure is shown in EG 201 399 [i.3].
ETSI
---------------------- Page: 7 ----------------------
8 Final draft ETSI EN 301 908-5 V4.1.2 (2009-12)
1 Scope
The present document applies to the following radio equipment types:
• Base stations for IMT-2000 CDMA multi-carrier (cdma2000) and Evolved CDMA Multi-Carrier Ultra Mobile
Broadband (UMB).
These radio equipment types are capable of operating in all or any part of the frequency bands given in table 1-1.
Table 1-1: CDMA multi-carrier Base Station operating bands
Band Class (BC) Direction of transmission CDMA multi-carrier Base Station
operating bands
Transmit 2 110 MHz to 2 170 MHz
6
Receive 1 920 MHz to 1 980 MHz
Transmit 1 805 MHz to 1 880 MHz
8
Receive 1 710 MHz to 1 785 MHz
Transmit 925 MHz to 960 MHz
9
Receive 880 MHz to 915 MHz
Transmit 2 620 MHz to 2 690 MHz
13
Receive 2 500 MHz to 2 570 MHz
The present document covers requirements for IMT-2000 CDMA multi-carrier (cdma2000) User Equipments and
Evolved CDMA Multi-Carrier (UMB) User Equipment.
Base stations for IMT-2000 CDMA multi-carrier (cdma2000) may support:
1) operation in cdma2000 spread spectrum systems as defined in 3GPP2 C.S0002-D [2], referred to herein as
operation in Type 1 cdma2000 systems; or
2) operation in cdma2000 High Rate Packet Data Systems as defined in TIA-856 [7], referred to herein in Type 2
cdma2000 systems.
The present document is intended to cover the provisions of Directive 1999/5/EC [i.2] (R&TTE Directive) article 3.2,
which states that "[…] radio equipment shall be so constructed that it effectively uses the spectrum allocated to
terrestrial/space radio communications and orbital resources so as to avoid harmful interference".
In addition to the present document, other ENs that specify technical requirements in respect of essential requirements
under other parts of article 3 of the R&TTE Directive [i.2] may apply to equipment within the scope of the present
document.
NOTE: A list of such ENs is included on the web site http://www.newapproach.org/.
2 References
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific.
• For a specific reference, subsequent revisions do not apply.
• Non-specific reference may be made only to a complete document or a part thereof and only in the following
cases:
- if it is accepted that it will be possible to use all future changes of the referenced document for the
purposes of the referring document;
- for informative references.
Referenced documents which are not found to be publicly available in the expected location might be found at
http://docbox.etsi.org/Reference.
ETSI
---------------------- Page: 8 ----------------------
9 Final draft ETSI EN 301 908-5 V4.1.2 (2009-12)
NOTE: While any hyperlinks included in this clause were valid at the time of publication ETSI cannot guarantee
their long term validity.
2.1 Normative references
The following referenced documents are indispensable for the application of the present document. For dated
references, only the edition cited applies. For non-specific references, the latest edition of the referenced document
(including any amendments) applies.
[1] ANSI/TIA-97-F-1 (June 2006): "Recommended Minimum Performance Standards for cdma2000
Spread Spectrum Base Stations - Addendum 1".
[2] 3GPP2 C.S0002-D V2.0 (September 2005): "Physical Layer Standard for cdma2000 Spread
Spectrum Systems Revision D".
NOTE: Available at: http://www.3gpp2.org/Public_html/Specs/C.S0002-D_v2.0_051006.pdf.
[3] ANSI/TIA-98-F-1 (June 2006): "Recommended Minimum Performance Standards for cdma2000
Spread Spectrum Mobile Stations - Addendum".
[4] TIA/EIA-126-D (June 2001): "Loopback Service Options Standard (LSO) for cdma Spread
Spectrum Systems".
[5] TIA-870-A (March 2005): "Test Data Service Option (TDSO) for cdma2000 Spread Spectrum
Systems - Revision A".
[6] TIA/EIA/IS-871 (April 2001): "Markov Service Option (MSO) for cdma2000 Spread Spectrum
Systems".
[7] TIA-856-B-1 (October 2007): "cdma2000 High Rate Packet Data Air Interface Specification".
[8] 3GPP2 C.S0032-B V1.0 (May 2008): "Recommended Minimum Performance Standards for
cdma2000 High Rate Packet Data Access Network".
NOTE: Available at: http://www.3gpp2.org/Public_html/specs/C.S0032-B_v1.0_080519.pdf.
[9] 3GPP2 C.S0029-B V1.0 (March 2008): "Test Application Specification (TAS) for High Rate
Packet Data Air Interface".
NOTE: Available at: http://www.3gpp2.org/Public_html/specs/C.S0029-B_v1.0_080409.pdf.
[10] ETSI EN 301 908-1 (V4.1.2): "Electromagnetic compatibility and Radio spectrum Matters (ERM);
Base Stations (BS), Repeaters and User Equipment (UE) for IMT-2000 Third-Generation cellular
ne
...
Draft ETSI EN 301 908-5 V4.1.1 (2009-04)
Harmonized European Standard (Telecommunications series)
Electromagnetic compatibility
and Radio spectrum Matters (ERM);
Base Stations (BS), Repeaters and User Equipment (UE) for
IMT-2000 Third-Generation cellular networks;
Part 5: Harmonized EN for IMT-2000, CDMA Multi-Carrier
(cdma2000) and Evolved CDMA Multi-Carrier Ultra Mobile
Broadband (UMB) (BS) covering the essential requirements of
article 3.2 of the R&TTE Directive
---------------------- Page: 1 ----------------------
2 Draft ETSI EN 301 908-5 V4.1.1 (2009-04)
Reference
REN/ERM-TFES-005-5
Keywords
3G, 3GPP2, cdma2000, cellular, digital,
IMT-2000, mobile, radio, regulation, UMTS
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
Individual copies of the present document can be downloaded from:
http://www.etsi.org
The present document may be made available in more than one electronic version or in print. In any case of existing or
perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF).
In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive
within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
http://portal.etsi.org/chaircor/ETSI_support.asp
Copyright Notification
No part may be reproduced except as authorized by written permission.
The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2009.
All rights reserved.
TM TM TM TM
DECT , PLUGTESTS , UMTS , TIPHON , the TIPHON logo and the ETSI logo are Trade Marks of ETSI registered
for the benefit of its Members.
TM
3GPP is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners.
LTE™ is a Trade Mark of ETSI currently being registered
for the benefit of its Members and of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3 Draft ETSI EN 301 908-5 V4.1.1 (2009-04)
Contents
Intellectual Property Rights . 6
Foreword . 6
Introduction . 7
1 Scope . 8
2 References . 8
2.1 Normative references . 9
2.2 Informative references . 9
3 Definitions, symbols and abbreviations . 10
3.1 Definitions . 10
3.2 Symbols . 18
3.3 Abbreviations . 22
4 Technical requirements specifications . 23
4.1 Environmental profile . 23
4.2 Conformance requirements . 23
4.2.1 Introduction. 23
4.2.2 Transmitter conducted spurious emissions . 23
4.2.2.1 Definition . 23
4.2.2.2 Limits . 24
4.2.2.3 Conformance . 26
4.2.3 Maximum output power . 26
4.2.3.1 Definition . 26
4.2.3.2 Limits . 26
4.2.3.2.1 Base stations operating in Type 1 cdma2000 systems . 26
4.2.3.2.2 Base stations operating in Type 2 cdma2000 systems . 26
4.2.3.3 Conformance . 27
4.2.4 Inter-base station transmitter intermodulation . 27
4.2.4.1 Definition . 27
4.2.4.2 Limits . 27
4.2.4.3 Conformance . 27
4.2.5 Receiver conducted spurious emissions . 28
4.2.5.1 Definition . 28
4.2.5.2 Limits . 28
4.2.5.3 Conformance . 28
4.2.6 Receiver blocking characteristics . 28
4.2.6.1 Definition . 28
4.2.6.2 Limits . 28
4.2.6.2.1 Base stations operating in Type 1 cdma2000 systems . 28
4.2.6.2.2 Base stations operating in Type 2 cdma2000 systems . 28
4.2.6.3 Conformance . 28
4.2.7 Intermodulation spurious response attenuation . 29
4.2.7.1 Definition . 29
4.2.7.2 Limits . 29
4.2.7.2.1 Base stations operating in Type 1 cdma2000 systems . 29
4.2.7.2.2 Base stations operating in Type 2 cdma2000 systems . 29
4.2.7.3 Conformance . 29
4.2.8 Adjacent channel selectivity . 29
4.2.8.1 Definition . 29
4.2.8.2 Limits . 29
4.2.8.2.1 Base stations operating in Type 1 cdma2000 systems . 29
4.2.8.2.2 Base stations operating in Type 2 cdma2000 systems . 29
4.2.8.3 Conformance . 29
5 Testing for compliance with technical requirements . 30
5.1 Conditions for testing . 30
ETSI
---------------------- Page: 3 ----------------------
4 Draft ETSI EN 301 908-5 V4.1.1 (2009-04)
5.1.1 Introduction. 30
5.1.2 Standard equipment under test . 30
5.1.2.1 Basic equipment . 30
5.1.2.2 Ancillary equipment . 30
5.2 Interpretation of the measurement results . 30
5.3 Essential radio test suites . 30
5.3.1 Transmitter conducted spurious emissions . 31
5.3.1.1 Test procedure for base stations supporting operation in Type 1 cdma2000 systems . 31
5.3.1.2 Test procedure for base stations supporting operation in Type 2 cdma2000 systems . 31
5.3.2 Maximum output power . 32
5.3.2.1 Test procedure for base stations supporting operation in Type 1 cdma2000 systems . 32
5.3.2.2 Test procedure for base stations supporting operation in Type 2 cdma2000 systems . 32
5.3.3 Inter-base station transmitter intermodulation . 33
5.3.3.1 Test procedure for base stations supporting operation in Type 1 cdma2000 systems . 33
5.3.3.2 Test procedure for base stations supporting operation in Type 2 cdma2000 systems 2 . 33
5.3.4 Receiver conducted spurious emissions . 34
5.3.4.1 Test procedure for base stations supporting operation in Type 1 or Type 2 cdma2000 systems . 34
5.3.5 Receiver blocking characteristics . 35
5.3.5.1 Test procedure for base stations supporting operation in Type 1 cdma2000 systems . 35
5.3.5.2 Test procedure for base stations supporting operation in Type 2 cdma2000 systems . 36
5.3.6 Intermodulation spurious response attenuation . 36
5.3.6.1 Test procedure for base stations supporting operation in Type 1 cdma2000 systems . 36
5.3.6.2 Test procedure for base stations supporting operation in Type 2 cdma2000 systems . 37
5.3.7 Adjacent channel selectivity . 37
5.3.7.1 Test procedure for base stations supporting operation in Type 1 cdma2000 systems . 37
5.3.7.2 Test procedure for base stations supporting operation in Type 2 cdma2000 systems . 38
Annex A (normative): HS Requirements and conformance Test specifications Table (HS-
RTT) . 39
Annex B (normative): Base station Configurations . 41
B.1 Receiver diversity . 41
B.2 Duplexers . 41
B.3 Power supply options . 41
B.4 Ancillary RF amplifiers . 42
B.5 BS using antenna arrays . 42
B.5.1 Receiver tests . 43
B.5.2 Transmitter tests . 43
Annex C (informative): Environmental profile and standard test conditions . 44
C.1 Introduction . 44
C.2 CDMA environmental requirements . 44
C.2.1 Temperature and power supply voltage . 44
C.2.1.1 Definition . 44
C.2.1.2 Method of measurement . 44
C.2.1.3 Minimum standard . 45
C.2.2 High humidity . 45
C.2.2.1 Definition . 45
C.2.2.2 Method of measurement . 45
C.2.2.3 Minimum standard . 45
C.3 Standard test conditions. 45
C.3.1 Standard environmental test conditions . 45
C.3.2 Standard conditions for the primary power supply . 46
C.3.2.1 General . 46
C.3.2.2 Standard DC test voltage from accumulator batteries . 46
C.3.2.3 Standard AC voltage and frequency . 46
ETSI
---------------------- Page: 4 ----------------------
5 Draft ETSI EN 301 908-5 V4.1.1 (2009-04)
Annex D (informative): The EN title in the official languages . 47
Annex E (informative): Bibliography . 48
History . 49
ETSI
---------------------- Page: 5 ----------------------
6 Draft ETSI EN 301 908-5 V4.1.1 (2009-04)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (http://webapp.etsi.org/IPR/home.asp).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This Harmonized European Standard (Telecommunications series) has been produced by ETSI Technical Committee
Electromagnetic compatibility and Radio spectrum Matters (ERM), and is now submitted for the Public Enquiry phase
of the ETSI standards Two-step Approval Procedure.
The present document has been produced by ETSI in response to a mandate from the European Commission issued
under Council Directive 98/34/EC [i.1] (as amended) laying down a procedure for the provision of information in the
field of technical standards and regulations.
The present document is intended to become a Harmonized Standard, the reference of which will be published in the
Official Journal of the European Communities referencing the Directive 1999/5/EC [i.2] of the European Parliament
and of the Council of 9 March 1999 on radio equipment and telecommunications terminal equipment and the mutual
recognition of their conformity ("the R&TTE Directive").
Technical specifications relevant to Directive 1999/5/EC [i.2] are given in annex A.
The present document is part 5 of a multi-part deliverable covering the Base Stations (BS), Repeaters and User
Equipment (UE) for IMT-2000 Third-Generation cellular networks, as identified below:
Part 1: "Harmonized EN for IMT-2000, introduction and common requirements, covering the essential
requirements of article 3.2 of the R&TTE Directive";
Part 2: "Harmonized EN for IMT-2000, CDMA Direct Spread (UTRA FDD and E-UTRA FDD) (UE) covering
the essential requirements of article 3.2 of the R&TTE Directive";
Part 3: "Harmonized EN for IMT-2000, CDMA Direct Spread (UTRA FDD and E-UTRA FDD) (BS) covering
the essential requirements of article 3.2 of the R&TTE Directive";
Part 4: "Harmonized EN for IMT-2000, CDMA Multi-Carrier (cdma2000) and Evolved CDMA Multi-Carrier
Ultra Mobile Broadband (UMB) (UE) covering the essential requirements of article 3.2 of the R&TTE
Directive";
Part 5: "Harmonized EN for IMT-2000, CDMA Multi-Carrier (cdma2000) and Evolved CDMA
Multi-Carrier Ultra Mobile Broadband (UMB) (BS) covering the essential requirements of article
3.2 of the R&TTE Directive";
Part 6: "Harmonized EN for IMT-2000, CDMA TDD (UTRA TDD and E-UTRA TDD) (UE) covering the
essential requirements of article 3.2 of the R&TTE Directive";
Part 7: "Harmonized EN for IMT-2000, CDMA TDD (UTRA TDD and E-UTRA TDD) (BS) covering the
essential requirements of article 3.2 of the R&TTE Directive";
Part 8: "Harmonized EN for IMT-2000, TDMA Single-Carrier (UWC 136) (UE) covering essential requirements
of article 3.2 of the R&TTE Directive";
Part 9: "Harmonized EN for IMT-2000, TDMA Single-Carrier (UWC 136) (BS) covering essential requirements
of article 3.2 of the R&TTE Directive";
ETSI
---------------------- Page: 6 ----------------------
7 Draft ETSI EN 301 908-5 V4.1.1 (2009-04)
Part 10: "Harmonized EN for IMT-2000, FDMA/TDMA (DECT) covering essential requirements of article 3.2 of
the R&TTE Directive";
Part 11: "Harmonized EN for IMT-2000, CDMA Direct Spread (UTRA FDD and E-UTRA FDD) (Repeaters)
covering the essential requirements of article 3.2 of the R&TTE Directive";
Part 12: "Harmonized EN for IMT-2000, CDMA Multi-Carrier (cdma2000) (Repeaters) covering the essential
requirements of article 3.2 of the R&TTE Directive";
Part 13: "Harmonized EN for IMT-2000, Evolved Universal Terrestrial Radio Access (E-UTRA) (UE) covering
the essential requirements of article 3.2 of the R&TTE Directive";
Part 14: "Harmonized EN for IMT-2000, Evolved Universal Terrestrial Radio Access (E-UTRA) (BS) covering
the essential requirements of article 3.2 of the R&TTE Directive";
Part 15: "Harmonized EN for IMT-2000, Evolved Universal Terrestrial Radio Access (E-UTRA) (FDD
Repeaters) covering the essential requirements of article 3.2 of the R&TTE Directive";
Part 16: "Harmonized EN for IMT-2000, Evolved CDMA Multi-Carrier Ultra Mobile Broadband (UMB) (UE)
covering the essential requirements of article 3.2 of the R&TTE Directive";
Part 17: "Harmonized EN for IMT-2000, Evolved CDMA Multi-Carrier Ultra Mobile Broadband (UMB) (BS)
covering the essential requirements of article 3.2 of the R&TTE Directive".
Proposed national transposition dates
Date of latest announcement of this EN (doa): 3 months after ETSI publication
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 6 months after doa
Date of withdrawal of any conflicting National Standard (dow): 18 months after doa
Introduction
The present document is part of a set of standards developed by ETSI and is designed to fit in a modular structure to
cover all radio and telecommunications terminal equipment within the scope of the R&TTE Directive [i.2]. The
modular structure is shown in EG 201 399 [i.3].
ETSI
---------------------- Page: 7 ----------------------
8 Draft ETSI EN 301 908-5 V4.1.1 (2009-04)
1 Scope
The present document applies to the following radio equipment types:
• Base stations for IMT-2000 CDMA multi-carrier (cdma2000) and Evolved CDMA Multi-Carrier Ultra Mobile
Broadband (UMB).
These radio equipment types are capable of operating in all or any part of the frequency bands given in table 1.1.
Table 1.1: CDMA multi-carrier base station operating bands
Band Class (BC) Direction of transmission CDMA multi-carrier base station
operating bands
Transmit 2 110 MHz to 2 170 MHz
6
Receive 1 920 MHz to 1 980 MHz
Transmit 1 805 MHz to 1 880 MHz
8
Receive 1 710 MHz to 1 785 MHz
Transmit 925 MHz to 960 MHz
9
Receive 880 MHz to 915 MHz
Transmit 2 620 MHz to 2 690 MHz
13
Receive 2 500 MHz to 2 570 MHz
The present document covers requirements for IMT-2000 CDMA multi-carrier (cdma2000) User Equipments and
Evolved CDMA Multi-Carrier (UMB) User Equipment.
Base stations for IMT-2000 CDMA multi-carrier (cdma2000) may support:
1) operation in cdma2000 spread spectrum systems as defined in 3GPP2 C.S0002-D [2], referred to herein as
operation in Type 1 cdma2000 systems; or
2) operation in cdma2000 High Rate Packet Data Systems as defined in TIA-856 [7], referred to herein in Type 2
cdma2000 systems.
The present document is intended to cover the provisions of Directive 1999/5/EC [i.2] (R&TTE Directive) article 3.2,
which states that "[…] radio equipment shall be so constructed that it effectively uses the spectrum allocated to
terrestrial/space radio communications and orbital resources so as to avoid harmful interference".
In addition to the present document, other ENs that specify technical requirements in respect of essential requirements
under other parts of article 3 of the R&TTE Directive [i.2] may apply to equipment within the scope of the present
document.
NOTE: A list of such ENs is included on the web site http://www.newapproach.org/.
2 References
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific.
• For a specific reference, subsequent revisions do not apply.
• Non-specific reference may be made only to a complete document or a part thereof and only in the following
cases:
- if it is accepted that it will be possible to use all future changes of the referenced document for the
purposes of the referring document;
- for informative references.
Referenced documents which are not found to be publicly available in the expected location might be found at
http://docbox.etsi.org/Reference.
ETSI
---------------------- Page: 8 ----------------------
9 Draft ETSI EN 301 908-5 V4.1.1 (2009-04)
NOTE: While any hyperlinks included in this clause were valid at the time of publication ETSI cannot guarantee
their long term validity.
2.1 Normative references
The following referenced documents are indispensable for the application of the present document. For dated
references, only the edition cited applies. For non-specific references, the latest edition of the referenced document
(including any amendments) applies.
[1] ANSI/TIA-97-F-1 (June 2006): "Recommended Minimum Performance Standards for cdma2000
Spread Spectrum Base Stations - Addendum 1".
[2] 3GPP2 C.S0002-D V2.0 (September 2005): "Physical Layer Standard for cdma2000 Spread
Spectrum Systems Revision D".
NOTE: Available at: http://www.3gpp2.org/Public_html/Specs/C.S0002-D_v2.0_051006.pdf.
[3] ANSI/TIA-98-F-1 (June 2006): "Recommended Minimum Performance Standards for cdma2000
Spread Spectrum Mobile Stations - Addendum".
[4] TIA/EIA-126-D (June 2001): "Loopback Service Options Standard (LSO) for cdma Spread
Spectrum Systems".
[5] TIA-870-A (March 2005): "Test Data Service Option (TDSO) for cdma2000 Spread Spectrum
Systems - Revision A".
[6] TIA/EIA/IS-871 (April 2001): "Markov Service Option (MSO) for cdma2000 Spread Spectrum
Systems".
[7] TIA-856-B-1 (October 2007): "cdma2000 High Rate Packet Data Air Interface Specification".
[8] 3GPP2 C.S0032-B V1.0 (May 2008): "Recommended Minimum Performance Standards for
cdma2000 High Rate Packet Data Access Network".
NOTE: Available at: http://www.3gpp2.org/Public_html/specs/C.S0032-B_v1.0_080519.pdf.
[9] 3GPP2 C.S0029-B V1.0 (March 2008): "Test Application Specification (TAS) for High Rate
Packet Data Air Interface".
NOTE: Available at: http://www.3gpp2.org/Public_html/specs/C.S0029-B_v1.0_080409.pdf.
[10] ETSI EN 301 908-1 (V4.1.1): "Electromagnetic compatibility and Radio spectrum Matters (ERM);
Base Stations (BS), Repeaters and User Equipment (UE) for IMT-2000 Third-Generation cellular
networks; Part 1: H
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.