SIST EN 3273:2004
(Main)Aerospace series - Pipe coupling 8°30' - Dynamic beam seal end for elbows, tees and crosses - Geometric configuration
Aerospace series - Pipe coupling 8°30' - Dynamic beam seal end for elbows, tees and crosses - Geometric configuration
This standard specifies the dimensions of the dynamic beam seal end for elbows, tees and crosses for pipe couplings 8°30', nominal pressure up to 28 000 kPa, for aerospace applications.
Luft- und Raumfahrt - Rohrverschraubung 8°30' - Dichtlippe für Winkel-, T- und Kreuzverschraubungen - Konstruktionsblatt
Diese Norm legt die Maße der Dichtlippen für Winkel-, T- und Kreuzverschraubungen für Rohrverschrau-bungen 8°30', Nenndruck bis 28 000 kPa, zur Verwendung in der Luft- und Raumfahrt fest.
Série aérospatiale - Systeme de raccordement 8°30' - Joints a levre, pour raccords coudés, raccords en té et raccords en croix - Configuration géometrique
La présente norme spécifie les dimensions des joints a levre pour raccords coudés, raccords en té et raccords en croix pour les systemes de raccordement 8°30', pression nominale jusqu'a 28 000 kPa, pour applications aérospatiales.
Aerospace series - Pipe coupling 8°30' - Dynamic beam seal end for elbows, tees and crosses - Geometric configuration
General Information
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Aerospace series - Pipe coupling 8°30' - Dynamic beam seal end for elbows, tees and crosses - Geometric configurationLuft- und Raumfahrt - Rohrverschraubung 8°30' - Dichtlippe für Winkel-, T- und Kreuzverschraubungen - KonstruktionsblattSérie aérospatiale - Systeme de raccordement 8°30' - Joints a levre, pour raccords coudés, raccords en té et raccords en croix - Configuration géometriqueAerospace series - Pipe coupling 8°30' - Dynamic beam seal end for elbows, tees and crosses - Geometric configuration49.080Aerospace fluid systems and componentsICS:Ta slovenski standard je istoveten z:EN 3273:2001SIST EN 3273:2004en01-maj-2004SIST EN 3273:2004SLOVENSKI
STANDARD
SIST EN 3273:2004
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 3273October 2001ICS 49.080English versionAerospace series - Pipe coupling 8°30' - Dynamic beam sealend for elbows, tees and crosses - Geometric configurationSérie aérospatiale - Système de raccordement 8°30' - Jointà lèvre, pour raccords coudés, raccords en té et raccordsen croix - Configuration géométriqueLuft- und Raumfahrt - Rohrverschraubung 8°30' - Dichtlippefür Winkel-, T- und Kreuzverschraubungen -KonstruktionsblattThis European Standard was approved by CEN on 29 December 2000.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2001 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 3273:2001 ESIST EN 3273:2004
EN 3273:2001 (E)2ForewordThis European Standard has been prepared by the European Association of Aerospace Manufacturers(AECMA).After inquiries and votes carried
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.