SIST EN IEC 62149-10:2019

Fibre optic active components and devices - Performance standards - Part 10: Radio-over-fibre (RoF) transceivers for mobile fronthaul (IEC 62149-10:2018)

This part of IEC 62149 covers the performance specification for radio-over-fibre (RoF)
transceivers used for mobile fronthaul systems. The performance standard contains a
definition of the product performance requirements together with a series of tests and
measurements with clearly defined conditions, severities, and pass/fail criteria. The tests are
intended to be run on a one-off basis to prove any product's ability to satisfy the performance
standard's requirements.
A product that has been shown to meet all the requirements of a performance standard can
be declared to be in compliance with the performance standard.

Aktive Lichtwellenleiterbauelemente und -geräte - Betriebsverhaltensnormen - Teil 10: RoF-Sende-Empfangsgeräte (Funk über Lichtwellenleiter) für Mobilfunk Fronthaul-Anwendungen

Composants et dispositifs actifs fibroniques - Normes de performances - Partie 10: Émetteurs récepteurs radio sur fibre (RoF) pour le fronthaul des réseaux mobiles

IEC 62149-10:2018 couvre la spécification de performance des émetteurs-récepteurs radio sur fibre (RoF) utilisés dans les réseaux fronthaul mobiles. La norme de performance contient une définition des exigences de performance du produit, accompagnée d'une série d'essais et de mesures comportant des conditions, des sévérités et des critères de conformité/non-conformité clairement définis. Les essais visant à attester de l'aptitude d'un produit à satisfaire aux exigences de la norme de performance sont destinés à être réalisés sur la base d'un essai unique. Un produit dont il a été démontré qu'il satisfait à toutes les exigences d'une norme de performance peut être déclaré comme étant conforme à celle-ci.
Mots clés :2018 émetteurs-récepteurs radio sur fibre (RoF) utilisés dans les réseaux fronthaul mobiles

Aktivne optične komponente in naprave - Tehnični standardi - 10. del: Sprejemniki/oddajniki za radiofrekvenčni signal po optičnih kablih (RoF) v mobilnih dostopovnih povezavah (IEC 62149-10:2018)

Ta del standarda IEC 62149 zajema tehnično specifikacijo za sprejemnike/oddajnike za prenos radijskih signalov po optičnih kablih (RoF), ki se uporabljajo v sistemih mobilnega radijskega omrežja. Tehnični standard vsebuje opredelitev zahtev glede zmogljivosti za izdelek skupaj z naborom preskusov in meritev z jasno določenimi pogoji, stopnjami zahtevnosti in merili za uspešno/neuspešno opravljen preskus. Preskusi so namenjeni enkratnemu izvajanju, z njimi pa se dokaže, ali lahko izdelek izpolnjuje zahteve tehničnega standarda.
Izdelek, ki dokazano izpolnjuje vse zahteve tehničnega standarda, je mogoče šteti za skladnega s tehničnim standardom.

General Information

• Status: Published
• Publication Date: 16-Jan-2019
• ICS: 33.180.20 - Fibre optic interconnecting devices
• Technical Committee: MOC - Mobile Communications
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 19-Dec-2018
• Due Date: 23-Feb-2019
• Completion Date: 17-Jan-2019
• Ref Project: EN IEC 62149-10:2018 - Fibre optic active components and devices - Performance standards - Part 10: Radio-over-fibre (RoF) transceivers for mobile fronthaul

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN IEC 62149-10:2019
01-marec-2019
Aktivne optične komponente in naprave - Tehnični standardi - 10. del:
Sprejemniki/oddajniki za radiofrekvenčni signal po optičnih kablih (RoF) v
mobilnih dostopovnih povezavah (IEC 62149-10:2018)
Fibre optic active components and devices - Performance standards - Part 10: Radio-
over-fibre (RoF) transceivers for mobile fronthaul (IEC 62149-10:2018)
Aktive Lichtwellenleiterbauelemente und -geräte - Betriebsverhaltensnormen - Teil 10:
RoF-Sende-Empfangsgeräte (Funk über Lichtwellenleiter) für Mobilfunk Fronthaul-
Anwendungen
Composants et dispositifs actifs fibroniques - Normes de performances - Partie 10:
Émetteurs récepteurs radio sur fibre (RoF) pour le fronthaul des réseaux mobiles
Ta slovenski standard je istoveten z: EN IEC 62149-10:2018
ICS:
33.180.20 Povezovalne naprave za Fibre optic interconnecting
optična vlakna devices
SIST EN IEC 62149-10:2019 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN IEC 62149-10:2019

---------------------- Page: 2 ----------------------

SIST EN IEC 62149-10:2019


EUROPEAN STANDARD EN IEC 62149-10

NORME EUROPÉENNE

EUROPÄISCHE NORM
December 2018
ICS 33.180.99

English Version
Fibre optic active components and devices - Performance
standards - Part 10: Radio-over-fibre (RoF) transceivers for
mobile fronthaul
(IEC 62149-10:2018)
Composants et dispositifs actifs fibroniques - Normes de Aktive Lichtwellenleiterbauelemente und -geräte -
performances - Partie 10: Émetteurs récepteurs radio sur Betriebsverhaltensnormen - Teil 10: RoF-Sende-
fibre (RoF) pour le fronthaul des réseaux mobiles(IEC Empfangsgeräte (Funk über Lichtwellenleiter) für Mobilfunk
62149-10:2018) Fronthaul-Anwendungen
(IEC 62149-10:2018)
This European Standard was approved by CENELEC on 2018-12-12. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden,
Switzerland, Turkey and the United Kingdom.



European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2018 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
 Ref. No. EN IEC 62149-10:2018 E

---------------------- Page: 3 ----------------------

SIST EN IEC 62149-10:2019
EN IEC 62149-10:2018 (E)
European foreword
The text of document 86C/1501/CDV, future edition 1 of IEC 62149-10, prepared by SC 86C "Fibre
optic systems and active devices" of IEC/TC 86 "Fibre optics" was submitted to the IEC-CENELEC
parallel vote and approved by CENELEC as EN IEC 62149-10:2018.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2019-09-12
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2021-12-12
document have to be withdrawn

Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
Endorsement notice
The text of the International Standard IEC 62149-10:2018 was approved by CENELEC as a European
Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards
indicated:
IEC 60191(series) NOTE Harmonized as EN 60191 (series)
IEC 60749 (series) NOTE Harmonized as EN 60749 (series)
IEC 60793-2 (series) NOTE Harmonized as EN 60793-2 (series)
IEC 60794-2 NOTE Harmonized as EN 60794-2
IEC 60825 (series) NOTE Harmonized as EN 60825 (series)
IEC 60874 (series) NOTE Harmonized in EN 60874 (series)
IEC 61281-1 NOTE Harmonized as EN IEC 61281-1
IEC 61290-1-3 NOTE Harmonized as EN 61290-1-3
IEC 61300-2-4 NOTE Harmonized as EN 61300-2-4
IEC 61300-2-19 NOTE Harmonized as EN 61300-2-19
IEC 61300-2-48 NOTE Harmonized as EN 61300-2-48
IEC 62007-1 NOTE Harmonized as EN 62007-1
IEC 62007-2 NOTE Harmonized as EN 62007-2
IEC 62148-1 NOTE Harmonized as EN IEC 62148-1
IEC 62149-1 NOTE Harmonized as EN 62149-1
IEC 62149-8 NOTE Harmonized as EN 62149-8
IEC 62149-9 NOTE Harmonized as EN 62149-9
2

---------------------- Page: 4 ----------------------

SIST EN IEC 62149-10:2019
EN IEC 62149-10:2018 (E)
Annex ZA
(normative)

Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1  Where an International Publication has been modified by common modifications, indicated by (mod), the relevant
EN/HD applies.
NOTE 2  Up-to-date information on the latest versions of the European Standards listed in this annex is available here:
www.cenelec.eu.
Publication Year Title EN/HD Year
IEC 60068-2-6 -  Environmental testing - Part 2-6: Tests - Test EN 60068-2-6 -
Fc: Vibration (sinusoidal)
IEC 60068-2-20 -  Environmental testing - Part 2-20: Tests - Test EN 60068-2-20 -
T: Test methods for solderability and resistance
to soldering heat of devices with leads
IEC 60068-2-27 -  Environmental testing - Part 2-27: Tests - Test EN 60068-2-27 -
Ea and guidance: Shock
IEC 60068-2-38 -  Environmental testing - Part 2-38: Tests - Test EN 60068-2-38 -
Z/AD: Composite temperature/humidity cyclic
test
IEC 60068-2-78 -  Environmental testing - Part 2-78: Tests - Test EN 60068-2-78 -
Cab: Damp heat, steady state
IEC 60749-25 -  Semiconductor devices - Mechanical and EN 60749-25 -
climatic test methods - Part 25: Temperature
cycling
IEC 60749-26 -  Semiconductor devices - Mechanical and EN IEC 60749-26 -
climatic test methods - Part 26: Electrostatic
discharge (ESD) sensitivity testing - Human
body model (HBM)
IEC 60825-1 -  Safety of laser products - Part 1: Equipment EN 60825-1 -
classification and requirements
IEC 60950-1 (mod) -  Information technology equipment - Safety - EN 60950-1 -
Part 1: General requirements
IEC 61300-2-47 -  Fibre optic interconnecting devices and passive EN 61300-2-47 -
components - Basic test and measurement
procedures - Part 2-47: Tests - Thermal shocks
ITU-T -  Supplement 55, Radio-over-fibre (RoF) - -
Recommendation technologies and their applications
G.Sup55

3

---------------------- Page: 5 ----------------------

SIST EN IEC 62149-10:2019

---------------------- Page: 6 ----------------------

SIST EN IEC 62149-10:2019




IEC 62149-10

®


Edition 1.0 2018-11




INTERNATIONAL



STANDARD




NORME



INTERNATIONALE
colour

inside










Fibre optic active components and devices – Performance standards –

Part 10: Radio-over-fibre (RoF) transceivers for mobile fronthaul




Composants et dispositifs actifs fibroniques – Normes de performances –

Partie 10: Émetteurs récepteurs radio sur fibre (RoF) pour le fronthaul des

réseaux mobiles















INTERNATIONAL

ELECTROTECHNICAL

COMMISSION


COMMISSION

ELECTROTECHNIQUE


INTERNATIONALE




ICS 33.180.99 ISBN 978-2-8322-6174-3




Warning! Make sure that you obtained this publication from an authorized distributor.

Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé.

® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale

---------------------- Page: 7 ----------------------

SIST EN IEC 62149-10:2019
– 2 – IEC 62149-10:2018 © IEC 2018
CONTENTS
FOREWORD . 3
INTRODUCTION . 5
1 Scope . 6
2 Normative references . 6
3 Terms, definitions, symbols and abbreviated terms . 7
3.1 Terms and definitions . 7
3.2 Symbols . 7
3.3 Abbreviated terms . 7
4 Product parameters . 8
4.1 Absolute limiting ratings . 8
4.2 Operating environment . 8
4.3 Functional specification. 8
5 Testing . 8
5.1 General . 8
5.2 Characterization testing . 9
5.3 Performance testing . 9
6 Environmental specifications . 9
6.1 General safety . 9
6.2 Laser safety . 9
6.3 Electromagnetic compatibility (EMC) requirements. 9
Annex A (normative) Specifications for RoF transceivers for mobile fronthaul . 10
A.1 Absolute limiting ratings . 10
A.2 Operating environment . 10
A.3 Functional specification. 10
A.4 Diagrams . 11
A.5 Labelling . 13
A.6 Testing . 13
A.6.1 General . 13
A.6.2 Characterization testing . 14
A.6.3 Performance testing. 14
Annex B (normative) Sample size and grouping requirements . 17
Bibliography . 18

Figure A.1 – Block diagram of RoF transceiver . 12
Figure A.2 – Interface/reference points compliant with ITU-T G-Series
Recommendations – Supplement 55 . 13

Table 1 – Operating environment . 8
Table A.1 – Absolute limiting ratings . 10
Table A.2 – Functional specification . 11
Table A.3 – Characterization tests . 14
Table A.4 – Performance test plan . 15
Table B.1 – Sample size, sequencing and grouping requirements . 17

---------------------- Page: 8 ----------------------

SIST EN IEC 62149-10:2019
IEC 62149-10:2018 © IEC 2018 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________

FIBRE OPTIC ACTIVE COMPONENTS AND DEVICES –
PERFORMANCE STANDARDS –

Part 10: Radio-over-fibre (RoF) transceivers for mobile fronthaul

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as "IEC
Publication(s)"). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 62149-10 has been prepared by subcommittee 86C: Fibre optic
systems and active devices, of IEC technical committee 86: Fibre optics.
The text of this International Standard is based on the following documents:
CDV Report on voting
86C/1501/CDV 86C/1531/RVC

Full information on the voting for the approval of this International Standard can be found in
the report on voting indicated in the above table.
This document has been drafted in accordance with the ISO/IEC Directives, Part 2.

---------------------- Page: 9 ----------------------

SIST EN IEC 62149-10:2019
– 4 – IEC 62149-10:2018 © IEC 2018
A list of all parts in the IEC 62149 series, published under the general title Fibre optic active
components and devices – Performance standards, can be found on the IEC website.
The committee has decided that the contents of this document will remain unchanged until the
stability date indicated on the IEC website under "http://webstore.iec.ch" in the data related to
the specific document. At this date, the document will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.

IMPORTANT – The 'colour inside' logo on the cover page of this publication indicates
that it contains colours which are considered to be useful for the correct
understanding of its contents. Users should therefore print this document using a
colour printer.

---------------------- Page: 10 ----------------------

SIST EN IEC 62149-10:2019
IEC 62149-10:2018 © IEC 2018 – 5 –
INTRODUCTION
This part of IEC 62149 covers the performance specification for radio-over-fibre (RoF)
transceivers in fibre optic mobile fronthaul applications. The performance criteria are
generally well specified for a number of internationally agreed application areas, such as
ITU-T G-series Recommendations – Supplement 55. This document provides optical interface
specifications toward the realization of transversely compatible mobile fronthaul systems
based on RoF technology. RoF transceivers for mobile fronthaul systems are supplied by
different manufacturers, but those manufacturers do not guarantee the operation of RoF
transceivers in mobile fronthaul systems. Manufacturers using this document are responsible
for meeting the required performance and/or reliability and quality assurance under a
recognized scheme.

---------------------- Page: 11 ----------------------

SIST EN IEC 62149-10:2019
– 6 – IEC 62149-10:2018 © IEC 2018
FIBRE OPTIC ACTIVE COMPONENTS AND DEVICES –
PERFORMANCE STANDARDS –

Part 10: Radio-over-fibre (RoF) transceivers for mobile fronthaul



1 Scope
This part of IEC 62149 covers the performance specification for radio-over-fibre (RoF)
transceivers used for mobile fronthaul systems. The performance standard contains a
definition of the product performance requirements together with a series of tests and
measurements with clearly defined conditions, severities, and pass/fail criteria. The tests are
intended to be run on a one-off basis to prove any product's ability to satisfy the performance
standard's requirements.
A product that has been shown to meet all the requirements of a performance standard can
be declared to be in compliance with the performance standard.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their
content constitutes requirements of this document. For dated references, only the edition
cited applies. For undated references, the latest edition of the referenced document (including
any amendments) applies.
IEC 60068-2-6, Environmental testing – Part 2-6: Tests – Test Fc: Vibration (sinusoidal)
IEC 60068-2-20, Environmental testing – Part 2-20: Tests – Test T: Test methods for
solderability and resistance to soldering heat of devices with leads
IEC 60068-2-27, Environmental testing – Part 2-27: Tests – Test Ea and guidance: Shock
IEC 60068-2-38, Environmental testing – Part 2-38: Tests – Test Z/AD: Composite
temperature/humidity cyclic test
IEC 60068-2-78, Environmental testing – Part 2-78: Tests – Test Cab: Damp heat, steady
state
IEC 60749-25, Semiconductor devices – Mechanical and climatic test methods – Part 25:
Temperature cycling
IEC 60749-26,
...