SIST EN 14617-8:2008
(Main)Agglomerated stone - Test methods - Part 8: Determination of resistance to fixing (dowel hole)
Agglomerated stone - Test methods - Part 8: Determination of resistance to fixing (dowel hole)
The present European standard specifies a test method to determine the breaking load at the dowel hole of agglomerated stones slabs used for cladding or lining in building.
Künstlich hergestellter Stein - Prüfverfahren - Teil 8: Bestimmung der Beständigkeit gegen Befestigungen (Ankerdornloch)
Pierre agglomérée - Méthodes d'essai - Détermination de la résistance aux attaches (trou pour broches)
Aglomeriran kamen - Preskusne metode - 8. del: Ugotavljanje odpornosti pritrditve (sidrna izvrtina)
General Information
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Agglomerated stone - Test methods - Part 8: Determination of resistance to fixing (dowel hole)Aglomeriran kamen - Preskusne metode - 8. del: Ugotavljanje odpornosti pritrditve (sidrna izvrtina)Pierre agglomérée - Méthodes d'essai - Détermination de la résistance aux attaches (trou pour broches)Künstlich hergestellter Stein - Prüfverfahren - Teil 8: Bestimmung der Beständigkeit gegen Befestigungen (Ankerdornloch)Ta slovenski standard je istoveten z:EN 14617-8:2007SIST EN 14617-8:2008en,fr,de91.100.15ICS:SLOVENSKI
STANDARDSIST EN 14617-8:200801-april-2008
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 14617-8October 2007ICS 91.100.15 English VersionAgglomerated stone - Test methods - Part 8: Determination ofresistance to fixing (dowel hole)Pierre agglomérée - Méthodes d'essai - Partie 8 :Détermination de la résistance aux attaches (trous pourbroches)Künstlich hergestellter Stein - Prüfverfahren - Teil 8:Bestimmung der Beständigkeit gegen Befestigungen(Ankerdornloch)This European Standard was approved by CEN on 26 August 2007.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2007 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 14617-8:2007: E
EN 14617-8:2007 (E) 2 Contents Page Foreword.3 1 Scope.4 2 Normative references.4 3 Principle.4 4 Symbols.4 5 Apparatus.4 6 Preparation of the specimens.5 6.1 Sampling.5 6.2 Test specimens.5 6.2.1 General.5 6.2.2 Tests.5 6.2.3 Number of specimens.5 6.2.4 Surface finish of the specimens.5 6.2.5 Dimensions of the specimens.5 6.2.6 Location of the holes.6 6.2.7 Dimensions and tolerances of the holes.6 6.2.8 Drilling the holes.6 6.2.9 Conditioning.6 6.2.10 Measuring d and d1.6 6.3 Clamping device.7 7 Dowels.9 7.1 Dimensions and tolerances.9 7.2 Material.9 7.3 Placing the dowels.9 8 Test procedure.9 9 Expression of the results.10 10 Test report.10 Annex A (normative)
Statistical evaluation of the test results.12 A.1 Scope.12 A.2 Symbols and definitions.12 A.3 Statistical evaluation of test results.13
EN 14617-8:2007 (E) 3 Foreword This document (EN 14617-8:2007) has been prepared by Technical Committee CEN/TC 246 “Natural stones”, the secretariat of which is held by UNI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by April 2008, and conflicting national standards shall be withdrawn at the latest by April 2008. Test methods for agglomerated stones consist of the following: EN 14617-1, Agglomerated stone — Test methods — Part 1: Determination of apparent density and water absorption EN 14617-2, Agglomerated stone — Test methods — Part 2: Determination of flexural strength (bending) EN 14617-4, Agglomerated stone — Test methods — Part 4: Determination of the abrasion resistance EN 14617-5, Agglomerated stone — Test methods — Part 5: Determination of freeze and thaw resistance EN 14617-6, Agglomerated stone — Test methods — Part 6: Determination of thermal shock resistance EN 14617-8, Agglomerated stone — Test methods — Part 8: Determination of resistance to fixing (dowel hole) EN 14617-9, Agglomerated stone — Test methods — Part 9: Determination of impact resistance EN 14617-10, Agglomerated stone — Test methods — Part 10: Determination of chemical resistance EN 14617-11, Agglomerated stone — Test methods — Part 11: Determination of linear thermal expansion coefficient EN 14617-12, Agglomerated stone — Test methods — Part 12: Determination of dimensional stability EN 14617-13, Agglomerated stone — Test methods — Part 13: Determination of electrical resistivity EN 14617-15, Agglomerated stone — Test methods — Part 15: Determination of compressive strength EN 14617-16, Agglomerated stone — Test methods — Part 16: Determination of dimensions, geometric characteristics and surface quality of modular tiles No existing standard is superseded. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EN 14617-8:2007 (E) 4 1 Scope This European Standard specifies a test method to determine the breaking load at the dowel hole of agglomerated stones slabs used for cladding or lining in buildings. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 197-1, Cement — Part 1: Composition, specifications and conformity criteria for common cements EN 10088-1, Stainless steels — Part 1: List of stainless steels EN 12390-4, Testing hardened concrete — Part 4: Compressive strength — Specification for testing machines 3 Principle This test consists of applying a force in a direction perpendicular to the face of a specimen through a dowel previously placed in a hole drilled in one of its sides and measuring the breaking load of the specimen. 4 Symbols For the purposes of this document, the following symbols apply. d is the thickness of the test specimen, in millimetres 1d is the distance from the hole wall to the face where fracture occurs, in millimetres Ab is the maximum distance of the centre of the hole to the fracture edge on the face, in millimet
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.