iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
SIST

SIST EN ISO 10350:1999

(Main)

Plastics - Acquisition and presentation of comparable single-point data (ISO 10350:1993)

Plastics - Acquisition and presentation of comparable single-point data (ISO 10350:1993)

Kunststoffe - Ermittlung und Darstellung vergleichbarer Einpunktkennwerte (ISO 10350:1993)

Diese Internationale Norm legt spezifische Prüfverfahren zur Ermittlung und Darstellung vergleichbarer Kennwerte von gewissen grundlegenden Kunststoff- Eigenschaften fest. Allgemein ist jede Eigenschaft durch einen einzelnen Meßwert dargestellt, während in gewissen Fällen zwei unter verschiedenen Prüfbedingungen ermittelte Kennwerte eine Eigenschaft darlegen. Die aufgeführten Eigenschaften werden üblicherweise in Datenblättern von Erzeugern geboten.

Plastiques - Acquisitions et présentation de caractéristiques intrinseques comparables (ISO 10350:1993)

Polimerni materiali - Pridobitev in predstavitev primerljivih značilnih enotočkovnih podatkov (ISO 10350:1993)

General Information

Status
Withdrawn
Publication Date
30-Apr-1999
Withdrawal Date
30-Apr-2003
ICS
83.080.01 - Plastics in general
Technical Committee
IPMA - Polimer materials and products
Current Stage
9900 - Withdrawal (Adopted Project)
Start Date
01-May-2003
Due Date
01-May-2003
Completion Date
01-May-2003
Ref Project
EN ISO 10350:1995 - Plastics - Acquisition and presentation of comparable single-point data (ISO 10350:1993)

Relations

Replaced By
SIST EN ISO 10350-1:2001 - Plastics - Acquisition and presentation of comparable single-point data - Part 1: Moulding materials (ISO 10350-1:1998)
Effective Date
22-Dec-2008
Replaced By
SIST EN ISO 10350-2:2002 - Plastics - Acquisition and presentation of comparable single-point data - Part 2: Long-fibre-reinforced plastics (ISO 10350-2:2001)
Effective Date
22-Dec-2008

Buy Standard

EN ISO 10350:1999EN ISO 10350:1999
PreviousNext
Standard
EN ISO 10350:1999
English language
9 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 10350:1999
01-maj-1999
3ROLPHUQLPDWHULDOL3ULGRELWHYLQSUHGVWDYLWHYSULPHUOMLYLK]QDþLOQLKHQRWRþNRYQLK
SRGDWNRY ,62
Plastics - Acquisition and presentation of comparable single-point data (ISO 10350:1993)
Kunststoffe - Ermittlung und Darstellung vergleichbarer Einpunktkennwerte (ISO
10350:1993)
Plastiques - Acquisitions et présentation de caractéristiques intrinseques comparables
(ISO 10350:1993)
Ta slovenski standard je istoveten z: EN ISO 10350:1995
ICS:
83.080.01 Polimerni materiali na Plastics in general
splošno
SIST EN ISO 10350:1999 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 10350:1999

---------------------- Page: 2 ----------------------

SIST EN ISO 10350:1999

---------------------- Page: 3 -----------------
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

SIST
SIST EN ISO 6186:2023(Main)
Plastics - Determination of pourability (ISO 6186:2023)
EN ISO 6186:2023

This document specifies two methods, A and B, for determining the pourability of plastics in powdered and granular form, by measuring the flow time through a funnel under specified conditions.
From method A, information concerning the processability can be derived, whilst method B is especially designed for process control during manufacture.
The methods specified are not necessarily applicable to all plastics in powdered and granular form.

  • Standard
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    8 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 6603-2:2023(Main)
Plastics - Determination of puncture impact behaviour of rigid plastics - Part 2: Instrumented impact testing (ISO 6603-2:2023)
EN ISO 6603-2:2023

This document specifies a test method for the determination of puncture impact properties of rigid plastics, in the form of flat specimens, using instruments for measuring force and deflection. It is applicable if a force-deflection or force-time diagram, recorded at nominal constant striker velocity, is necessary for detailed characterization of the impact behaviour.
The test method is applicable to specimens with a thickness between 1 mm to 4 mm.
The method is suitable for use with the following types of material:
—    rigid thermoplastic moulding and extrusion materials, including filled, unfilled and reinforced compounds and sheets;
—    rigid thermosetting moulding and extrusion materials, including filled and reinforced compounds, sheets and laminates;
—    fibre-reinforced thermoset and thermoplastic composites incorporating unidirectional or multi-directional reinforcements such as mats, woven fabrics, woven rovings, chopped strands, combination and hybrid reinforcements, rovings, milled fibres and sheets made from pre-impregnated materials (prepregs).
The method is also applicable to specimens which are either moulded or machined from finished products, laminates and extruded or cast sheet.
The test results are comparable only if the conditions of preparation of the specimens, their dimensions and surfaces as well as the test conditions are the same. In particular, results determined on specimens of different thickness cannot be compared with one another (see Annex E). Comprehensive evaluation of the reaction to impact stress can be obtained by determinations made as a function of impact velocity and temperature for different material variables, such as crystallinity and moisture content.
The impact behaviour of finished products cannot be predicted directly from this test, but specimens may be taken from finished products (see above) for tests by this method.
Test data developed by this method is not intended to be used for design calculations. However, information on the typical behaviour of the material can be obtained by testing at different temperatures and impact velocities (see Annex D) by varying the thickness (see Annex E) and by testing specimens prepared under different conditions.
It is not the purpose of this document to give an interpretation of the mechanism occurring on every particular point of the force-deflection diagram. These interpretations are a task for scientific research.

  • Standard
    42 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    34 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 179-1:2023(Main)
Plastics - Determination of Charpy impact properties - Part 1: Non-instrumented impact test (ISO 179-1:2023)
EN ISO 179-1:2023

ISO 179-1:2010 specifies a method for determining the Charpy impact strength of plastics under defined conditions. A number of different types of specimen and test configurations are defined. Different test parameters are specified according to the type of material, the type of test specimen and the type of notch.
The method can be used to investigate the behaviour of specified types of specimen under the impact conditions defined and for estimating the brittleness or toughness of specimens within the limitations inherent in the test conditions. It can also be used for the determination of comparative data from similar types of material.
The method has a greater range of applicability than that given in ISO 180 (Izod impact testing) and is more suitable for the testing of materials showing interlaminar shear fracture or of materials exhibiting surface effects due to environmental factors.
The method is suitable for use with the following range of materials:
rigid thermoplastic moulding and extrusion materials (including filled and reinforced compounds in addition to unfilled types) and rigid thermoplastics sheets;
rigid thermosetting moulding materials (including filled and reinforced compounds) and rigid thermosetting sheets (including laminates);
fibre-reinforced thermosetting and thermoplastic composites incorporating unidirectional or multi-directional reinforcements (such as mats, woven fabrics, woven rovings, chopped strands, combination and hybrid reinforcements, rovings and milled fibres) or incorporating sheets made from pre-impregnated materials (prepregs), including filled compounds;
thermotropic liquid-crystal polymers.

  • Standard
    30 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    27 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 180:2023(Main)
Plastics - Determination of Izod impact strength (ISO 180:2023)
EN ISO 180:2023

1.1 This document specifies a method for determining the Izod impact strength of plastics under defined conditions. A number of different types of specimen and test configurations are defined. Different test parameters are specified according to the type of material, the type of test specimen and the type of notch.
1.2 The method is used to investigate the behaviour of specified types of specimen under the impact conditions defined and for estimating the brittleness or toughness of specimens within the limitations inherent in the test conditions.
1.3 The method is suitable for use with the following range of materials:
— rigid thermoplastic moulding and extrusion materials, including filled and reinforced compounds in addition to unfilled types; rigid thermoplastics sheets;
— rigid thermosetting moulding materials, including filled and reinforced compounds; rigid thermosetting sheets, including laminates;
— fibre-reinforced thermosetting and thermoplastic composites incorporating unidirectional or non-unidirectional reinforcements such as mat, woven fabrics, woven rovings, chopped strands, combination and hybrid reinforcements, rovings and milled fibres and sheet made from pre-impregnated materials (prepregs);
— thermotropic liquid-crystal polymers.
1.4 The method is not normally suitable for use with rigid cellular materials and sandwich structures containing cellular material. Notched specimens are also not normally used for long-fibre-reinforced composites or thermotropic liquid-crystal polymers.
1.5 The method is suited to the use of specimens which can be either moulded to the chosen dimensions, machined from the central portion of a standard multipurpose test specimen (see ISO 20753) or machined from finished or semi-finished products such as mouldings, laminates and extruded or cast sheet.
1.6 The method specifies preferred dimensions for the test specimen. Tests which are carried out on specimens of different dimensions or with different notches, or specimens which are prepared under different conditions, may produce results which are not comparable. Other factors, such as the energy capacity of the apparatus, its impact velocity and the conditioning of the specimens can also influence the results. Consequently, when comparative data are required, these factors are to be carefully controlled and recorded.
1.7 The method is not intended to be used as a source of data for design calculations. Information on the typical behaviour of a material can be obtained, however, by testing at different temperatures, by varying the notch radius and/or the thickness and by testing specimens prepared under different conditions.

  • Standard
    22 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    18 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 11357-1:2023(Main)
Plastics - Differential scanning calorimetry (DSC) - Part 1: General principles (ISO 11357-1:2023)
EN ISO 11357-1:2023

ISO 11357-1:2016 specifies several differential scanning calorimetry (DSC) methods for the thermal analysis of polymers and polymer blends, such as
- thermoplastics (polymers, moulding compounds and other moulding materials, with or without fillers, fibres or reinforcements),
- thermosets (uncured or cured materials, with or without fillers, fibres or reinforcements), and
- elastomers (with or without fillers, fibres or reinforcements).
ISO 11357-1:2016 is intended for the observation and measurement of various properties of, and phenomena associated with, the above-mentioned materials, such as
- physical transitions (glass transition, phase transitions such as melting and crystallization, polymorphic transitions, etc.),
- chemical reactions (polymerization, crosslinking and curing of elastomers and thermosets, etc.),
- the stability to oxidation, and
- the heat capacity.
ISO 11357-1:2016 specifies a number of general aspects of differential scanning calorimetry, such as the principle and the apparatus, sampling, calibration and general aspects of the procedure and test report common to all following parts.
Details on performing specific methods are given in subsequent parts of ISO 11357 (see Foreword).

  • Standard
    43 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    40 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST ISO 171:2023(Main)
Plastics - Determination of bulk factor of moulding materials
ISO 171:2022

This document specifies a method of determining the bulk factor of a moulding material based on the ratio of the apparent volumetric density of a given quantity of particles and the corresponding material density.

  • Standard
    6 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    2 pages
    English language
    sale 15% off
  • Draft
    2 pages
    English language
    sale 15% off
  • Draft
    2 pages
    English language
    sale 15% off
SIST
SIST ISO 1675:2023(Main)
Plastics - Liquid resins - Determination of density by the pycnometer method
ISO 1675:2022

This document specifies a method for the determination of the density of liquid resins using a pycnometer.

  • Standard
    8 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    French language
    sale 15% off
  • Draft
    4 pages
    English language
    sale 15% off
  • Draft
    4 pages
    English language
    sale 15% off
SIST
SIST EN ISO 1675:2023(Main)
Plastics - Liquid resins - Determination of density by the pycnometer method (ISO 1675:2022)
EN ISO 1675:2022

This document specifies a method for the determination of the density of liquid resins using a pycnometer.

  • Standard
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    8 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST-TP CEN/TR 17910:2023(Main)
Biodegradable plastics - Status of standardization and new prospects
CEN/TR 17910:2022

This document summarizes the state of standardization in the field of biodegradable plastics and plastics products at CEN and ISO level. It explains the underlying scientific principles of biodegradation that provide the foundations for relevant test methods and enters into the merits of the individual tests to explain and clarify the reasons for the adoption of specific solutions and criteria.
In a second part, this document highlights areas where standardisation in this field is currently lacking and where future developments may be anticipated and useful.

  • Technical report
    43 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 11403-2:2022(Main)
Plastics - Acquisition and presentation of comparable multipoint data - Part 2: Thermal and processing properties (ISO 11403-2:2022)
EN ISO 11403-2:2022

This document specifies test procedures for the acquisition and presentation of multipoint data on the
following thermal and processing properties of plastics:
— enthalpy/temperature curve;
— linear-expansion/temperature curve;
— melt shear viscosity.

  • Standard
    16 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day