SIST EN ISO 1675:2023
(Main)Plastics - Liquid resins - Determination of density by the pycnometer method (ISO 1675:2022)
Plastics - Liquid resins - Determination of density by the pycnometer method (ISO 1675:2022)
This document specifies a method for the determination of the density of liquid resins using a pycnometer.
Kunststoffe – Flüssige Harze – Bestimmung der Dichte nach dem Pyknometer-Verfahren (ISO 1675:2022)
Dieses Dokument legt ein Verfahren zur Bestimmung der Dichte von flüssigen Harzen mit einem Pyknometer fest.
Plastiques - Résines liquides - Détermination de la masse volumique par la méthode du pycnomètre (ISO 1675:2022)
Le présent document spécifie une méthode de détermination de la masse volumique des résines liquides au moyen d’un pycnomètre.
Polimerni materiali - Tekoče smole - Določanje gostote s piknometrom (ISO 1675:2022)
Ta dokument določa metodo za določanje gostote tekoče smole s piknometrom.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 1675:2023
01-marec-2023
Nadomešča:
SIST EN ISO 1675:1999
Polimerni materiali - Tekoče smole - Določanje gostote s piknometrom (ISO
1675:2022)
Plastics - Liquid resins - Determination of density by the pycnometer method (ISO
1675:2022)
Kunststoffe – Flüssige Harze – Bestimmung der Dichte nach dem Pyknometer-Verfahren
(ISO 1675:2022)
Plastiques - Résines liquides - Détermination de la masse volumique par la méthode du
pycnomètre (ISO 1675:2022)
Ta slovenski standard je istoveten z: EN ISO 1675:2022
ICS:
83.080.01 Polimerni materiali na Plastics in general
splošno
SIST EN ISO 1675:2023 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 1675:2023
---------------------- Page: 2 ----------------------
SIST EN ISO 1675:2023
EN ISO 1675
EUROPEAN STANDARD
NORME EUROPÉENNE
December 2022
EUROPÄISCHE NORM
ICS 83.080.01 Supersedes EN ISO 1675:1998
English Version
Plastics - Liquid resins - Determination of density by the
pycnometer method (ISO 1675:2022)
Plastiques - Résines liquides - Détermination de la Kunststoffe - Flüssige Harze - Bestimmung der Dichte
masse volumique par la méthode du pycnomètre (ISO nach dem Pyknometer-Verfahren (ISO 1675:2022)
1675:2022)
This European Standard was approved by CEN on 6 December 2022.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 1675:2022 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 1675:2023
EN ISO 1675:2022 (E)
Contents Page
European foreword . 3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 1675:2023
EN ISO 1675:2022 (E)
European foreword
This document (EN ISO 1675:2022) has been prepared by Technical Committee ISO/TC 61 "Plastics" in
collaboration with Technical Committee CEN/TC 249 “Plastics” the secretariat of which is held by NBN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by June 2023, and conflicting national standards shall be
withdrawn at the latest by June 2023.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 1675:1998.
Any feedback and questions on this document should be directed to the users’ national standards
body/national committee. A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the
United Kingdom.
Endorsement notice
The text of ISO 1675:2022 has been approved by CEN as EN ISO 1675:2022 without any modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 1675:2023
---------------------- Page: 6 ----------------------
SIST EN ISO 1675:2023
INTERNATIONAL ISO
STANDARD 1675
Third edition
2022-12
Plastics — Liquid resins —
Determination of density by the
pycnometer method
Plastiques — Résines liquides — Détermination de la masse
volumique par la méthode du pycnomètre
Reference number
ISO 1675:2022(E)
© ISO 2022
---------------------- Page: 7 ----------------------
SIST EN ISO 1675:2023
ISO 1675:2022(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2022
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
© ISO 2022 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 1675:2023
ISO 1675:2022(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Principle . 1
5 Apparatus . 1
6 Procedure .2
6.1 Preparation of resin . 2
6.2 Measurement of density . 2
7 Expression of results . 2
8 Test report . 3
Bibliography .
...
SLOVENSKI STANDARD
oSIST prEN ISO 1675:2022
01-julij-2022
Polimerni materiali - Tekoče smole - Določanje gostote s piknometrom (ISO/DIS
1675:2022)
Plastics - Liquid resins - Determination of density by the pycnometer method (ISO/DIS
1675:2022)
Kunststoffe – Flüssige Harze – Bestimmung der Dichte nach dem Pyknometer-Verfahren
(ISO/DIS 1675:2022)
Plastiques - Résines liquides - Détermination de la masse volumique par la méthode du
pycnomètre (ISO/DIS 1675:2022)
Ta slovenski standard je istoveten z: prEN ISO 1675
ICS:
83.080.01 Polimerni materiali na Plastics in general
splošno
oSIST prEN ISO 1675:2022 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN ISO 1675:2022
---------------------- Page: 2 ----------------------
oSIST prEN ISO 1675:2022
DRAFT INTERNATIONAL STANDARD
ISO/DIS 1675
ISO/TC 61/SC 5 Secretariat: DIN
Voting begins on: Voting terminates on:
2022-05-03 2022-07-26
Plastics — Liquid resins — Determination of density by the
pycnometer method
Plastiques — Résines liquides — Détermination de la masse volumique par la méthode du pycnomètre
ICS: 83.080.01
This document is circulated as received from the committee secretariat.
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENT AND APPROVAL. IT IS
ISO/CEN PARALLEL PROCESSING
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/DIS 1675:2022(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION. © ISO 2022
---------------------- Page: 3 ----------------------
oSIST prEN ISO 1675:2022
ISO/DIS 1675:2022(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2022
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
© ISO 2022 – All rights reserved
---------------------- Page: 4 ----------------------
oSIST prEN ISO 1675:2022
ISO/DIS 1675:2022(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Principle . 1
5 Apparatus . 1
6 Procedure .2
6.1 Preparation of resin . 2
6.2 Measurement of density . 2
7 Expression of results . 2
8 Test report . 3
Bibliography . 4
iii
© ISO 2022 – All rights reserved
---------------------- Page: 5 ----------------------
oSIST prEN ISO 1675:2022
ISO/DIS 1675:2022(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.