iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
SIST

SIST HD 523.3.121 TO 122 S1:1998

(Main)

Specification for flexible insulating sleeving -- Part 3: Specification requirements for individual types of sleeving -- Sheets 121 and 122: Extruded silicone sleeving

Specification for flexible insulating sleeving -- Part 3: Specification requirements for individual types of sleeving -- Sheets 121 and 122: Extruded silicone sleeving

This standard gives requirements for two types of non-heat-shrinkable sleeving extruded from silicone elastomer and distinguished principally by volatile content - These sleevings are normally available in bore sizes up to 25 mm and in a range of wall thicknesses between 0.1 mm and 2.0 mm - National standards may select a restricted list of preferred combinations of bore diameter and wall thickness - These sleevings are normally available in the following opaque colours: black - blue - brown - grey - green - orange - pink - red - violet - white - yellow and green/yellow - It is also available in colourless translucent form

Bestimmung für Isolierschläuche -- Teil 3: Bestimmungen für einzelne Schlauchtypen -- Blätter 121 und 122: Extrudierte Siliconschläuche

Spécification pour gaines isolantes souples -- Partie 3: Spécifications particulières aux types particuliers de gaines -- Feuilles 121 et 122: Gaines en silicone extrudé

Specification for flexible insulating sleeving - Part 3: Specification requirements for individual types of sleeving - Sheets 121 to 122: Extruded silicone sleeving (IEC 60684-3-121 and 122:1988)

General Information

Status
Withdrawn
Publication Date
31-May-1998
Withdrawal Date
31-May-1998
ICS
29.035.20 - Plastics and rubber insulating materials
Technical Committee
IZO - Insulating materials
Current Stage
9900 - Withdrawal (Adopted Project)
Start Date
01-Jun-1998
Due Date
01-Jun-1998
Completion Date
01-Jun-1998
Ref Project
HD 523.3.121 & 122 S1:1990 - Specification for flexible insulating sleeving - Part 3: Specification requirements for individual types of sleeving - Sheets 121 and 122: Extruded silicone sleeving

Relations

Replaced By
SIST EN 60684-3-121 to 124:2002 - Flexible insulating sleeving -- Part 3: Specifications for individual types of sleeving -- Sheets 121 to 124: Extruded silicone sleeving
Effective Date
07-Jun-2022
Replaced By
SIST EN 60684-3-121 to 124:2002 - Flexible insulating sleeving -- Part 3: Specifications for individual types of sleeving -- Sheets 121 to 124: Extruded silicone sleeving
Effective Date
29-Jan-2023

Buy Standard

HD 523.3.121 TO 122 S1:1998HD 523.3.121 TO 122 S1:1998
PreviousNext
Standardization document
HD 523.3.121 TO 122 S1:1998
English language
8 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST HD 523.3.121 TO 122 S1:1998
01-junij-1998
Specification for flexible insulating sleeving - Part 3: Specification requirements
for individual types of sleeving - Sheets 121 to 122: Extruded silicone sleeving
(IEC 60684-3-121 and 122:1988)
Specification for flexible insulating sleeving -- Part 3: Specification requirements for
individual types of sleeving -- Sheets 121 and 122: Extruded silicone sleeving
Bestimmung für Isolierschläuche -- Teil 3: Bestimmungen für einzelne Schlauchtypen --
Blätter 121 und 122: Extrudierte Siliconschläuche
Spécification pour gaines isolantes souples -- Partie 3: Spécifications particulières aux
types particuliers de gaines -- Feuilles 121 et 122: Gaines en silicone extrudé
Ta slovenski standard je istoveten z: HD 523.3.121 & 122 S1:1990
ICS:
29.035.20 3ODVWLþQLLQJXPHQLL]RODFLMVNL Plastics and rubber insulating
PDWHULDOL materials
SIST HD 523.3.121 TO 122 S1:1998 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

SIST
SIST EN 60684-3-246:2007(Main)
Flexible insulating sleeving -- Part 3: Specifications for individual types of sleeving -- Sheet 246: Heat-shrinkable polyolefin sleeving, dual wall, not flame retarded
EN 60684-3-246:2007

This part of IEC 60684 defines requirements for dual wall, non-flame retarded, heat shrinkable, polyolefin sleeving. This sleeving has been found suitable for use up to 110 °C. The sleeving consists of an outer layer made of a semi-rigid cross-linked material. The inner layer is a substantially non-cross-linked polyolefin that flows and fuses during the shrinkage process to provide a seal. It is normally offered for sale with an internal diameter up to 25 mm in the following colours: black, white, red, yellow, blue and translucent. Sizes or colours other than those listed in this standard may be available as custom items. These items are considered to comply with this standard if they comply with the property requirements listed in Tables 2, 3, 4 and 5, excluding dimensions. Materials which conform to this specification meet established levels of performance. However, the selection of a material by a user for a specific application should be based on the actual requirements necessary for adequate performance in that application and not based on this specification alone.

  • Standard
    14 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 60454-2:2007(Main)
Pressure-sensitive adhesive tapes for electrical purposes -- Part 2: Methods of test
EN 60454-2:2007

This part of IEC 60454 specifies methods of test for pressure-sensitive adhesive tapes for electrical purposes.

  • Standard
    45 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 60684-3-211:2007(Main)
Flexible insulating sleeving -- Part 3: Specifications for individual types of sleeving -- Sheet 211: Heat-shrinkable sleeving, semi-rigid polyolefin, shrink ratio 2:1
EN 60684-3-211:2007

This part of IEC 60684 gives the requirements for four types of semi-rigid, heat-shrinkable polyolefin sleeving with a nominal shrink ratio of 2:1 that has been found suitable for temperatures up to 135 °C. - Type A: general purpose, flame-retarded, opaque colours; - Type B: general purpose, non flame-retarded, translucent; - Type C: fluid resistant, flame-retarded, opaque colours; - Type D: fluid resistant, non flame-retarded, translucent. The sleeving is normally available in internal diameter sizes up to 12,7 mm as supplied, in the following colours: black, white, red, yellow, blue and translucent. Sizes or colours other than those specifically listed in this standard may be available as custom items. The items are considered to comply with this standard if they comply with the property requirements listed in tables 2, 3 and also with the property requirements of Table 4 for types C and D, excluding dimensions. Materials which conform to this specification meet established levels of performance. However, the selection of a material by a user for a specific application should be based on the actual requirements necessary for adequate performance in that application and not based on this specification alone.

  • Standard
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 60454-3-11:2007(Main)
Pressure-sensitive adhesive tapes for electrical purposes -- Part 3: Specifications for individual materials -- Sheet 11: Polyester film combinations with glass filament, creped cellulosic paper, polyester non-woven, epoxy and pressure-sensitive adhesives
EN 60454-3-11:2007

This sheet of IEC 60454-3 contains the requirements for pressure-sensitive adhesive tapes, made with combined backings based on polyester film: - PET film/glass filament combination tapes; - Creped cellulosic paper/PET film combination tapes; - PET film/polyester non-woven combination tapes; - PET film/epoxy combination tapes. Materials which conform to this specification meet established levels of performance. However, the selection of a material by a user for a specific application should be based on the actual requirements necessary for adequate performance in that application, and not based on this specification alone.

  • Standard
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 60454-3-4:2007(Main)
Pressure-sensitive adhesive tapes for electrical purposes -- Part 3: Specifications for individual materials -- Sheet 4: Cellulose paper, creped and non-creped, with rubber thermosetting adhesive
EN 60454-3-4:2007

This sheet of IEC 60454-3 contains the requirements for pressure-sensitive adhesive tapes made with cellulose paper, creped and non-creped, with rubber thermosetting adhesive. Materials, which conform to this specification, meet established levels of performance. However, the selection of a material by a user for a specific application should be based on the actual requirements necessary for adequate performance in that application, and not based on this specification alone.

  • Standard
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 60684-3-248:2007(Main)
Flexible insulating sleeving -- Part 3: Specifications for individual types of sleeving -- Sheet 248: General purpose, heat-shrinkable, dual wall polyolefin sleeving, flame retarded, shrink ratios 2:1, 3:1, 4:1
EN 60684-3-248:2007

This part of IEC 60684 gives the requirements for six types of general purpose, heat shrinkable dual wall polyolefin sleevings, flame retarded with nominal shrink ratios of 2:1, 3:1 or 4:1 and available in low and high temperature adhesive inner walls. The low temperature adhesive sleeving has been found suitable for temperatures up to 105 °C and the high temperature adhesive sleeving has been found suitable for temperatures up to 125 °C. - Type AL: 2:1 shrink ratio, internal diameter up to 51 mm, low temperature adhesive inner wall. - Type AH: 2:1 shrink ratio, internal diameter up to 51 mm, high temperature adhesive inner wall. - Type BL: 3:1 shrink ratio, internal diameter up to 40 mm, low temperature adhesive inner wall. - Type BH: 3:1 shrink ratio, internal diameter up to 40 mm, high temperature adhesive inner wall. - Type CL: 4:1 shrink ratio, internal diameter up to 52 mm, low temperature adhesive inner wall. - Type CH: 4:1 shrink ratio, internal diameter up to 52 mm, high temperature adhesive inner wall. The sleeving consists of an outer layer being of a flexible cross-linked polyolefin. The inner wall consists of a hot melt adhesive that flows and fuses during the shrinking process to provide a bond. These sleevings are normally supplied in colour black. Sizes or colours other than those listed in this standard may be available as custom items. These items are considered to comply with this standard if they comply with the property requirements listed in Tables, 5 and 6 and Table 8 where applicable, with the exception of dimensions. Materials which conform to this specification meet established levels of performance. However, the selection of a material by a user for a specific application should be based on the actual requirements necessary for adequate performance in that application and not based on this specification alone.

  • Standard
    16 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 62329-2:2007(Main)
Heat shrinkable moulded shapes -- Part 2: Methods of test
EN 62329-2:2006

This part of IEC 62329 gives methods of test for heat-shrinkable moulded shapes in a range of configurations and materials suitable for insulation, environmental sealing, mechanical protection and strain relief for connector/cable terminations and multi-way transitions. The tests specified are designed to control the quality of the moulded shapes but it is recognized that they do not completely establish the suitability of moulded shapes for impregnation or encapsulation processes or other specialized applications. Where necessary, the test methods in this Part will need to be supplemented by appropriate impregnation or compatibility tests to suit the individual circumstances.

  • Standard
    51 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 60455-3-5:2006(Main)
Resin based reactive compounds used for electrical insulation -- Part 3: Specifications for individual materials -- Sheet 5: Unsaturated polyester based impregnating resins
EN 60455-3-5:2006

This sheet 5 of IEC 60455-3 gives the requirements for unsaturated polyester based impregnating resins, and includes requirements for certain properties at elevated temperature. Materials which conform to this specification meet established levels of performance. However, the selection of a material by a user for a specific application should be based on the actual requirements necessary for adequate performance in that application and not on this specification alone.

  • Standard
    14 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 60454-3-2:2006(Main)
Pressure-sensitive adhesive tapes for electrical purposes -- Part 3: Specifications for individual materials -- Sheet 2: Requirements for polyester film tapes with rubber thermosetting, rubber thermoplastic or acrylic crosslinked adhesives
EN 60454-3-2:2006

This sheet of IEC 60454-3 contains the requirements for: Polyester film tapes with rubber thermosetting, rubber thermoplastic or acrylic crosslinked adhesives Materials which conform to this specification meet established levels of performance. However, the selection of a material by a user for a specific application should be based on the actual requirements necessary for adequate performance in that application, and not based on this specification alone.

  • Standard
    12 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 60454-3-12:2006(Main)
Pressure-sensitive adhesive tapes for electrical purposes -- Part 3: Specifications for individual materials -- Sheet 12: Requirements for polyethylene and polypropylene film tapes with pressure sensitive adhesive
EN 60454-3-12:2006

This sheet of IEC 60454-3 contains requirements for polyethylene and polypropylene film tapes with pressure sensitive adhesives Materials which conform to this specification meet established levels of performance. However, the selection of a material by a user for a specific application should be based on the actual requirements necessary for adequate performance in that application, and not based on this specification alone.

  • Standard
    12 pages
    English language
    sale 10% off
    e-Library read for
    1 day