SIST EN 60603-7-71:2010

Connectors for electronic equipment - Part 7-71: Detail specification for 8-way, shielded, free and fixed connectors, for data transmission with frequencies up to 1 000 MHz (IEC 60603-7-71:2010)

This part of IEC 60603 covers 8-way, shielded, free and fixed connectors, references dimensional, mechanical, electrical and environmental characteristics and tests in IEC 60603- 7, and specifies electrical transmission requirements, including power sum alien (exogenous) crosstalk, for frequencies up to 1 000 MHz. These connectors are typically used as category 7A connectors in class FA cabling systems specified in ISO/IEC 11801. These connectors are intermateable and interoperable with other IEC 60603-7 series connectors as defined in Clause 2 of IEC 60603-7-1 and IEC 60603-7-7. These connectors are backward compatible with other IEC 60603-7 series connectors.

Steckverbinder für elektronische Einrichtungen - Teil 7-71: Bauartspezifikation für geschirmte freie und feste Steckverbinder, 8polig, für Datenübertragungen bis 1 000 MHz (IEC 60603-7-71:2010)

Connecteurs pour équipements électroniques - Partie 7-71: Spécification particulière pour les fiches et les embases blindées à 8 voies pour la transmission de données à des fréquences jusqu'à 1 000 MHz (CEI 60603-7-71:2010)

La CEI 60603-7-71:2010 couvre les fiches et les embases blindées à 8 voies et spécifie les exigences dimensionnelles, mécaniques, électriques et environnementales ainsi que les essais dans la CEI 60603-7 et elle spécifie les exigences de transmission électrique y compris la puissance de diaphonie exogène cumulée pour des fréquences jusqu'à 1 000 MHz. Ces connecteurs sont normalement utilisés comme connecteurs de catégorie 7A dans les systèmes de câblage de classe FA spécifiés dans l'ISO/CEI 11801. Ces connecteurs sont accouplables et interopérables avec les autres connecteurs de la série CEI 60603-7 comme cela est défini à l'Article 2 de la CEI 60603-7-1 et de la CEI 60603-7-7. Ces connecteurs offrent une compatibilité amont avec les autres connecteurs de la série CEI 60603-7.

Konektorji za elektronsko opremo - 7-71. del: Podrobna specifikacija za 8-redne, zaslonjene, proste in pritrjene konektorje za prenos podatkov s frekvencami do 1000 MHz (IEC 60603-7-71:2010)

Ta del IEC 60603 zajema 8-polne, zaslonjene, proste in fiksne konektorje in se sklicuje na merske, mehanske, električne in okoljske značilnosti in preskuse v IEC 60603-7 ter določa zahteve za prevajanje električnega toka za frekvence do 1 000 MHz. Ti konektorji se praviloma uporabljajo kot konektorji kategorije 7A iz razreda kabelskih sistemov FA, določenih v ISO/IEC 11801. Ti konektorji so medsebojno združljivi in interoperabilni z drugimi konektorji serije IEC 60603-7, kot je opredeljeno v Klavzuli 2 IEC 60603-7-1 in IEC 60603-7-7. Ti konektorji so povratno skladni z drugimi konektorji serije IEC 60603-7.

General Information

• Status: Published
• Publication Date: 14-Nov-2010
• ICS: 31.220.10 - Plug-and-socket devices. Connectors
• Technical Committee: I11 - Imaginarni 11
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 29-Oct-2010
• Due Date: 03-Jan-2011
• Completion Date: 15-Nov-2010
• Ref Project: EN 60603-7-71:2010 - Connectors for electronic equipment - Part 7-71: Detail specification for 8-way, shielded, free and fixed connectors, for data transmission with frequencies up to 1 000 MHz

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 60603-7-71:2010
01-december-2010
Konektorji za elektronsko opremo - 7-71. del: Podrobna specifikacija za 8-redne,
zaslonjene, proste in pritrjene konektorje za prenos podatkov s frekvencami do
1000 MHz (IEC 60603-7-71:2010)
Connectors for electronic equipment - Part 7-71: Detail specification for 8-way, shielded,
free and fixed connectors, for data transmission with frequencies up to 1 000 MHz (IEC
60603-7-71:2010)
Steckverbinder für elektronische Einrichtungen - Teil 7-71: Bauartspezifikation für
geschirmte freie und feste Steckverbinder, 8polig, für Datenübertragungen bis 1 000
MHz (IEC 60603-7-71:2010)
Connecteurs pour équipements électroniques - Partie 7-71: Spécification particulière
pour les fiches et les embases blindées à 8 voies pour la transmission de données à des
fréquences jusqu'à 1 000 MHz (CEI 60603-7-71:2010)
Ta slovenski standard je istoveten z: EN 60603-7-71:2010
ICS:
31.220.10 9WLþLLQYWLþQLFHNRQHNWRUML Plug-and-socket devices.
Connectors
SIST EN 60603-7-71:2010 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 60603-7-71:2010

---------------------- Page: 2 ----------------------

SIST EN 60603-7-71:2010

EUROPEAN STANDARD
EN 60603-7-71

NORME EUROPÉENNE
October 2010
EUROPÄISCHE NORM

ICS 31.220.10


English version


Connectors for electronic equipment -
Part 7-71: Detail specification for 8-way, shielded, free and fixed
connectors, for data transmission with frequencies up to 1 000 MHz
(IEC 60603-7-71:2010)


Connecteurs pour équipements Steckverbinder für elektronische
électroniques - Einrichtungen -
Partie 7-71: Spécification particulière pour Teil 7-71: Bauartspezifikation für
les fiches et les embases blindées à geschirmte freie und feste Steckverbinder,
8 voies pour la transmission de données à 8polig, für Datenübertragungen bis
des fréquences jusqu'à 1 000 MHz 1 000 MHz
(CEI 60603-7-71:2010) (IEC 60603-7-71:2010)




This European Standard was approved by CENELEC on 2010-10-01. CENELEC members are bound to comply
with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and notified
to the Central Secretariat has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus,
the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy,
Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia,
Spain, Sweden, Switzerland and the United Kingdom.

CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

Management Centre: Avenue Marnix 17, B - 1000 Brussels


© 2010 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 60603-7-71:2010 E

---------------------- Page: 3 ----------------------

SIST EN 60603-7-71:2010
EN 60603-7-71:2010 - 2 -
Foreword
The text of document 48B/2173/FDIS, future edition 1 of IEC 60603-7-71, prepared by SC 48B,
Connectors, of IEC TC 48, Electromechanical components and mechanical structures for electronic
equipment, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as
EN 60603-7-71 on 2010-10-01.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN and CENELEC shall not be held responsible for identifying any or all such patent
rights.
The following dates were fixed:
– latest date by which the EN has to be implemented
at national level by publication of an identical
national standard or by endorsement (dop) 2011-07-01
– latest date by which the national standards conflicting
with the EN have to be withdrawn (dow) 2013-10-01
Annex ZA has been added by CENELEC.
__________
Endorsement notice
The text of the International Standard IEC 60603-7-71:2010 was approved by CENELEC as a European
Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards indicated:
IEC 60512-2-1 NOTE  Harmonized as EN 60512-2-1.
IEC 60512-26-100:2008 NOTE  Harmonized as EN 60512-26-100:2008 (not modified).
__________

---------------------- Page: 4 ----------------------

SIST EN 60603-7-71:2010
- 3 - EN 60603-7-71:2010
Annex ZA
(normative)

Normative references to international publications
with their corresponding European publications

The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.

NOTE  When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD
applies.

Publication Year Title EN/HD Year

IEC 60512-1-100 - Connectors for electronic equipment - Tests EN 60512-1-100 -
and measurements -
Part 1-100: General - Applicable publications


IEC 60512-25-9 - Connectors for electronic equipment - Tests EN 60512-25-9 -
and measurements -
Part 25-9: Signal integrity tests - Test 25i:
Alien crosstalk


1) 1)
IEC 60512-27-100 201X Connectors for electronic equipment - Tests EN 60512-27-100 201X
and measurements -
Part 27-100: Signal integrity tests up to
500 MHz on IEC 60603-7 series connectors -
Tests 27a to 27g


IEC 60603-7 2008 Connectors for electronic equipment - EN 60603-7 2009
Part 7: Detail specification for 8-way,
unshielded, free and fixed connectors


IEC 60603-7-1 2009 Connectors for electronic equipment - EN 60603-7-1 2009
Part 7-1: Detail specification for 8-way,
shielded, free and fixed connectors


IEC 60603-7-7 2006 Connectors for electronic equipment - EN 60603-7-7 2006
Part 7-7: Detail specification for 8-way,
shielded, free and fixed connectors for data
transmission with frequencies up to 600 MHz


IEC 61156 Series Multicore and symmetrical pair/quad cables - -
for digital communications







1)
At draft stage.

---------------------- Page: 5 ----------------------

SIST EN 60603-7-71:2010

---------------------- Page: 6 ----------------------

SIST EN 60603-7-71:2010
IEC 60603-7-71
®
Edition 1.0 2010-06
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE


Connectors for electronic equipment –
Part 7-71: Detail specification for 8-way, shielded, free and fixed connectors,
for data transmission with frequencies up to 1 000 MHz

Connecteurs pour équipements électroniques –
Partie 7-71: Spécification particulière pour les fiches et les embases blindées
à 8 voies pour la transmission de données à des fréquences jusqu'à 1 000 MHz


INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
PRICE CODE
INTERNATIONALE
Q
CODE PRIX
ICS 31.220.10 ISBN 978-2-88912-028-4
® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale

---------------------- Page: 7 ----------------------

SIST EN 60603-7-71:2010
– 2 – 60603-7-71 © IEC:2010
CONTENTS
FOREWORD.4
INTRODUCTION.6
1 General .7
1.1 Scope.7
1.2 Normative references .7
2 Terms and definitions .8
3 Common features and isometric view .8
4 Cable terminations and internal connections – Fixed and free connectors .8
5 Gauges .8
6 Characteristics .8
6.1 General .8
6.2 Pin and pair grouping assignment .8
6.3 Classification into climatic category.8
6.4 Electrical characteristics.9
6.5 Transmission characteristics .9
6.5.1 General .9
6.5.2 Insertion loss.9
6.5.3 Return loss .9
6.5.4 Propagation delay .10
6.5.5 Delay skew.10
6.5.6 NEXT .10
6.5.7 Power sum NEXT (for information only) .10
6.5.8 FEXT.11
6.5.9 Power sum FEXT (for information only) .11
6.5.10 Transverse conversion loss .11
6.5.11 Transverse conversion transfer loss .11
6.5.12 Power sum alien (exogenous) NEXT.12
6.5.13 Power sum alien (exogenous) FEXT .12
6.6 Mechanical.13
6.6.1 Mechanical operation .13
6.6.2 Effectiveness of connector coupling devices.13
6.6.3 Insertion and withdrawal forces .13
7 Tests and test schedule.13
7.1 General .13
7.2 Arrangement for contact resistance test .13
7.3 Arrangement for vibration test .13
7.4 Test procedures and measuring methods .13
7.5 Preconditioning .13
7.6 Wiring and mounting of specimens .13
7.6.1 Wiring.13
7.6.2 Mounting .13
7.7 Test schedules .13
7.7.1 Basic (minimum) test schedule .13
7.7.2 Full test schedule .14
Bibliography.16

---------------------- Page: 8 ----------------------

SIST EN 60603-7-71:2010
60603-7-71 © IEC:2010 – 3 –
Table 1 – Test group EP .14

---------------------- Page: 9 ----------------------

SIST EN 60603-7-71:2010
– 4 – 60603-7-71 © IEC:2010
INTERNATIONAL ELECTROTECHNICAL COMMISSION
_____________

CONNECTORS FOR ELECTRONIC EQUIPMENT –

Part 7-71: Detail specification for 8-way, shielded,
free and fixed connectors, for data transmission
with frequencies up to 1 000 MHz


FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 60603-7-71 has been prepared by subcommittee 48B: Connectors,
of IEC technical committee 48: Electromechanical components and mechanical structures for
electronic equipment.
The text of this standard is based on the following documents:
FDIS Report on voting
48B/2173/FDIS 48B/2199/RVD

Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.

---------------------- Page: 10 ----------------------

SIST EN 60603-7-71:2010
60603-7-71 © IEC:2010 – 5 –
A list of all parts of the IEC 60603 series, under the general title Connectors for electronic
equipment, can be found on the IEC website.
The committee has decided that the contents of this publication will remain unchanged until
the stability date indicated on the IEC web site under "http://webstore.iec.ch" in the data
related to the specific publication. At this date, the publication will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.

---------------------- Page: 11 ----------------------

SIST EN 60603-7-71:2010
– 6 – 60603-7-71 © IEC:2010
INTRODUCTION
IEC 60603-7 is the bas
...