SIST EN 62271-2:2003
(Main)High-voltage switchgear and controlgear -- Part 2: Seismic qualification for rated voltages of 72,5 kV and above
High-voltage switchgear and controlgear -- Part 2: Seismic qualification for rated voltages of 72,5 kV and above
Applies to all switchgear and their assemblies for alternating current of rated voltages of 72,5 kV and above for indoor and outdoor installation, including their supporting structure rigidly connected to the ground. Where switchgear and their assemblies are not ground mounted, e.g. in a building, conditions for application are subject to agreement between users and manufacturers. The seismic qualification of the switchgear and their assemblies take into account any auxiliary and control equipment either directly mounted or as a separate structure. This standard provides procedures to seismically qualify ground mounted switchgear and their assemblies for rated voltages of 72,5 kV and above. The seismic qualification of the switchgear and their assemblies is only performed upon request. This standard specifies seismic severity levels and gives a choice of methods that may be applied to demonstrate the performance of high-voltage switchgear and their assemblies for which seismic qualification is required.
Hochspannungs-Schaltgeräte und -Schaltanlagen -- Teil 2: Erdbebenqualifikation für Bemessungsspannungen von 72,5 kV und darüber
Appareillage à haute tension -- Partie 2: Qualification sismique pour tension assignée égale ou supérieure à 72,5 kV
S'applique à tous les appareillages et à leurs assemblages, à courant alternatif de tension assignée égale ou supérieure à 72,5 kV, installés à l'intérieur ou l'extérieur, en incluant leurs châssis supports montés rigidement au sol. Dans le cas où les appareillages et leurs assemblages ne seraient pas montés au sol, par exemple dans un bâtiment, les conditions d'application font l'objet d'un accord entre les utilisateurs et les fabricants. La qualification sismique des appareillages et de leurs assemblages prend en compte tout équipement auxiliaire et de commande monté directement ou sur un châssis séparé. Cette norme donne des procédures pour la qualification sismique des appareillages et de leurs assemblages de tension assignée égale ou supérieure à 72,5 kV montés au sol. La qualification sismique d'un appareillage et de son assemblage n'est effectuée que sur demande. Cette norme spécifie des niveaux de sévérité sismique et propose un choix de méthodes qui peuvent être utilisées pour démontrer la conformité des appareillages haute tension et leurs assemblages pour lesquels une qualification sismique est exigée.
High-voltage switchgear and controlgear - Part 2: Seismic qualification for rated voltages of 72,5 kV and above
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 62271-2:2003
01-julij-2003
High-voltage switchgear and controlgear - Part 2: Seismic qualification for rated
voltages of 72,5 kV and above
High-voltage switchgear and controlgear -- Part 2: Seismic qualification for rated voltages
of 72,5 kV and above
Hochspannungs-Schaltgerte und -Schaltanlagen -- Teil 2: Erdbebenqualifikation fr
Bemessungsspannungen von 72,5 kV und darber
Appareillage haute tension -- Partie 2: Qualification sismique pour tension assigne gale
ou suprieure 72,5 kV
Ta slovenski standard je istoveten z: EN 62271-2:2003
ICS:
29.130.10 Visokonapetostne stikalne in High voltage switchgear and
krmilne naprave controlgear
SIST EN 62271-2:2003 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
EUROPEAN STANDARD EN 62271-2
NORME EUROPÉENNE
EUROPÄISCHE NORM April 2003
ICS 29.130.10
English version
High-voltage switchgear and controlgear
Part 2: Seismic qualification for rated voltages of 72,5 kV and above
(IEC 62271-2:2003)
Appareillage à haute tension Hochspannungs-Schaltgeräte und
Partie 2: Qualification sismique -Schaltanlagen
pour tension assignée Teil 2: Erdbebenqualifikation für
égale ou supérieure à 72,5 kV Bemessungsspannungen
(CEI 62271-2:2003) von 72,5 kV und darüber
(IEC 62271-2:2003)
This European Standard was approved by CENELEC on 2003-04-01. CENELEC members are bound to
comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and
notified to the Central Secretariat has the same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Czech Republic,
Denmark, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Luxembourg, Malta,
Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and United Kingdom.
CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
Central Secretariat: rue de Stassart 35, B - 1050 Brussels
© 2003 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 62271-2:2003 E
---------------------- Page: 2 ----------------------
EN 62271-2:2003 - 2 -
Foreword
The text
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.