SIST EN 10028-5:2003
(Main)Flat products made of steels for pressure purposes - Part 5: Weldable fine grain steels, thermomechanically rolled
Flat products made of steels for pressure purposes - Part 5: Weldable fine grain steels, thermomechanically rolled
This part of EN 10028 specifies the requirements for flat products for pressure equipments made of themomechanically rolled steels as listed in table 1. The steels are not suitable for hot forming. NOTE: Until now insufficient data for the standardization of the elevated temperature properties of these steels are available. If their use at such temperatures is intended the conditions for this shall be especially agreed between the interested parties. Other parts of this European Standard are: EN 10028-1 Flat products made of steels for pressure purposes - General requirements EN 10028-2 Flat products made of steels for pressure purposes - Part 2: Non-alloy and alloy steels with specified elevated temperature properties EN 10028-3 Flat producs made of steels for pressure purposes - Part 3: Weldable fine grain steels, normalized EN 10028-4 Flat products made of steels for pressure purposes - Part 4: Nickel-alloy steels with specified low temperature properties EN 10028-6 Flat products made of steels for pressure purposes - Part 6: Weldable fine grain steels, quenched and tempered EN 10028-7 Flat products made of steels for pressure purposes - Part 7: Stainless steels.
Flacherzeugnisse aus Druckbehälterstählen - Teil 5: Schweißgeeignete Feinkornbaustähle, thermomechanisch gewalzt
Produits plats en aciers pour appareils a pression - Partie 5: Aciers soudables a grains fins, laminés thermomécaniquement
Ploščati jekleni izdelki za tlačne posode – 5. del: Variva drobnozrnata jekla, toplotnomehansko valjana
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Flat products made of steels for pressure purposes - Part 5: Weldable fine grain steels, thermomechanically rolledProduits plats en aciers pour appareils a pression - Partie 5: Aciers soudables a grains fins, laminés thermomécaniquementFlacherzeugnisse aus Druckbehälterstählen - Teil 5: Schweißgeeignete Feinkornbaustähle, thermomechanisch gewalztTa slovenski standard je istoveten z:EN 10028-5:2003SIST EN 10028-5:2003en77.140.5077.140.30ICS:SIST EN 10028-5:19971DGRPHãþDSLOVENSKI
STANDARDSIST EN 10028-5:200301-november-2003
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 10028-5June 2003ICS 77.140.30; 77.140.50Supersedes EN 10028-5:1996English versionFlat products made of steels for pressure purposes - Part 5:Weldable fine grain steels, thermomechanically rolledProduits plats en aciers pour appareils à pression - Partie5: Aciers soudables à grains fins, laminésthermomécaniquementFlacherzeugnisse aus Druckbehälterstählen - Teil 5:Schweißgeeignete Feinkornbaustähle, thermomechanischgewalztThis European Standard was approved by CEN on 17 January 2003.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and UnitedKingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2003 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 10028-5:2003 E
EN 10028-5:2003 (E)2Contents pageForeword.31Scope.42Normative references.43Terms and definitions.44Dimension and tolerances.45Calculation of mass.46Classification and designation.46.1Classification.46.2Designation.57Information to be supplied by the purchaser.57.1Mandatory information.57.2Options.57.3Example for ordering.58Requirements.58.1Steelmaking process.58.2Delivery condition.58.3Chemical composition.68.4Mechanical properties.68.5Surface condition.68.6Internal soundness.69Inspection.69.1Types of inspection and inspection documents.69.2Tests to be carried out.69.3Retests.610Sampling.711Test methods.712Marking.7Annex ZA (informative)
Clauses of this European Standard addressing essential requirements or otherprovisions of EU Directives.Error! Bookmark not defined.Bibliography.14
EN 10028-5:2003 (E)3ForewordThis document EN 10028-5:2003 has been prepared by Technical Committee ECISS /TC 22, "Steels for pressurepurposes - Qualities", the secretariat of which is held by DIN.This European Standard shall be given the status of a national standard, either by publication of an identical text orby endorsement, at the latest by December 2003, and conflicting national standards shall be withdrawn at the latestby December 2003.This document supersedes EN 10028-5:1996.This document has been prepared under a mandate given to CEN by the European Commission and the EuropeanFree Trade Association, and supports essential requirements of EU Directive(s).For relationship with EU Directive(s), see informative annex ZA, which is an integral part of this document.This European Standard consists of the following parts, under the general title Flat products made of steels forpressure purposes:Part 1: General requirements Part 2: Non-alloy and alloy steels with specified elevated temperature propertiesPart 3: Weldable fine grain steels, normalizedPart 4: Nickel alloy steels with specified low temperature propertiesPart 5: Weldable fine grain steels, thermomechanically rolledPart 6: Weldable fine grain steels, quenched and temperedPart 7: Stainless steelsNOTEThe clauses marked by two points (··) contain information relating to agreements that may be made at the time ofenquiry and order.This document includes a Bibliography.According to the CEN/CENELEC Internal Regulations, the national standards organizations of the followingcountries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal,Slovakia, Spain, Sweden, Switzerland and the United Kingdom.
EN 10028-5:2003 (E)41 ScopeThis European Standard specifies the requirements for flat products for pressure equipments made ofthermomechanically rolled steels as specified in Table 1.The steels are not suitable for hot forming.NOTEUntil now no sufficient data for the standardization of the elevated temperature properties of these steels are availa-ble. If their use at such temperatures is intended the conditions for this should be specially agreed between the interested par-ties.The requirements of EN 10028-1 also apply.2 Normative referencesThis European Standard incorporates by dated or undated reference, provisions from other publications. Thesenormati
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.