SIST EN 50632-2-6:2015
(Main)Electric motor-operated tools - dust measurement procedure - Part 2-6: Particular requirements for hammers
Electric motor-operated tools - dust measurement procedure - Part 2-6: Particular requirements for hammers
This part of EN 50632 applies to hammers.
Motorbetriebene Elektrowerkzeuge - Staubmessverfahren - Teil 2-6: Besondere Anforderungen für Hämmer
Outils électriques à moteur - Procédure de mesure de la poussière - Partie 2-6: Exigences particulières pour les marteaux
Elektromotorna orodja - Postopek meritve prahu - 2-6. del: Posebne zahteve za kladiva
Ta del standarda EN 50632 se uporablja za kladiva.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 50632-2-6:2015
01-december-2015
Elektromotorna orodja - Postopek meritve prahu - 2-6. del: Posebne zahteve za
kladiva
Electric motor-operated tools - dust measurement procedure - Part 2-6: Particular
requirements for hammers
Motorbetriebene Elektrowerkzeuge - Staubmessverfahren - Teil 2-6: Besondere
Anforderungen für Hämmer
Ta slovenski standard je istoveten z: EN 50632-2-6:2015
ICS:
25.140.20 (OHNWULþQDRURGMD Electric tools
SIST EN 50632-2-6:2015 en,fr
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 50632-2-6:2015
---------------------- Page: 2 ----------------------
SIST EN 50632-2-6:2015
EUROPEAN STANDARD EN 50632-2-6
NORME EUROPÉENNE
EUROPÄISCHE NORM
September 2015
ICS 25.140.20
English Version
Electric motor-operated tools - dust measurement procedure -
Part 2-6: Particular requirements for hammers
To be completed Motorbetriebene Elektrowerkzeuge - Staubmessverfahren -
Teil 2-6: Besondere Anforderungen für Hämmer
This European Standard was approved by CENELEC on 2015-08-17. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2015 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN 50632-2-6:2015 E
---------------------- Page: 3 ----------------------
SIST EN 50632-2-6:2015
EN 50632-2-6:2015 (E)
Contents
European foreword . 3
1 Scope . 4
2 Normative references . 4
3 Terms and definitions . 4
4 Test procedure . 4
5 Instrumentation . 7
6 Information to be reported . 7
Figures
Figure 101 – A-support . 8
Figure 102 – Working position with rebar in concrete block . 9
Tables
Table 101 — Operating conditions for rotary hammers . 5
Table 102 — Concrete formulation (per cubic metre) . 5
Table 103 — Drilling specification . 6
Table 104 — Operating conditions for hammers without rotary action . 7
2
---------------------- Page: 4 ----------------------
SIST EN 50632-2-6:2015
EN 50632-2-6:2015 (E)
European foreword
This document (EN 50632-2-6:2015) was prepared by CLC/TC 116 “Safety of motor-operated electric
tools”.
The following dates are fixed:
(dop) 2016-08-17
• latest date by which this document has
to be implemented at national level by
publication of an identical national
standard or by endorsement
(dow) 2017-08-17
• latest date by which the national
standards conflicting with this
document have to be withdrawn
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such
patent rights.
This European Standard is divided into three parts:
Part 1: General requirements for the dust measurement which are common to electric motor-
operated tools (for the purpose of this standard referred to simply as tools);
Part 2 or 3: Requirements for the dust measurement for particular types of tools, which either
supplement or modify the requirements given in Part 1 to account for the particular
characteristics of these specific tools.
This Part 2 is to be used in conjunction with EN 50632-1:2015.
This Part 2 supplements or modifies the corresponding clauses in EN 50632-1:2015.
This Part 2 was developed to set out requirements for the measurement of the concentration for
inhalable and respirable dust emitted by hammers.
Where a particular subclause of Part 1 is not mentioned in this Part 2, that subclause applies as far as
reasonable. When this standard states "addition", "modification" or "replacement", the relevant text in
Part 1 is to be adapted accordingly.
Subclauses, notes, tables and figures which are additional to those in Part 1 are numbered starting
from 101.
The following print types are used:
- requirements; in roman type
- test specifications: in italic type;
- notes: in smaller roman type.
The terms defined in Clause 3 are printed in bold typeface.
3
---------------------- Page: 5 ----------------------
SIST EN 50632-2-6:2015
EN 50632-2-6:2015 (E)
1 Scope
This clause of Part 1 is applicable except as follows:
Addi
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.