SIST EN 301 908-2 V11.1.2:2017

IMT cellular networks - Harmonised Standard covering the essential requirements of article 3.2 of Directive 2014/53/EU - Part 2: CDMA Direct Spread (UTRA FDD) User Equipment (UE)

The present document applies to the following radio equipment type:
• User Equipment for IMT-2000 CDMA Direct Spread (UTRA FDD).
These radio equipment types are capable of operating in all or any part of the frequency bands given in table 1-1.
The present document covers requirements for UTRA FDD User Equipment from 3GPP™ Releases 99, 4, 5, 6, 7, 8, 9,
10 and 11 defined in ETSI TS 125 101 [4]. This include the requirements for UE operating bands from 3GPP™
Release 12 defined in ETSI TS 125 101 [4]. In addition, the present document covers requirements for UTRA FDD
User Equipment in the operating bands specified in ETSI TS 102 735 [i.4].
NOTE: For Band XX:
- for user equipment designed to be mobile or nomadic, the requirements in the present document
measured at the antenna port also show conformity to the corresponding requirement defined as
TRP (Total Radiated Power), as described in Commission Decision 2010/267/EU [i.6],
ECC Decision (09)03 [i.7] and CEPT Report 30 [i.8];
- for user equipment designed to be fixed or installed, the present document does not address the
requirements described in Commission Decision 2010/267/EU [i.6], ECC Decision (09)03 [i.7] and
CEPT Report 30 [i.8].
The present document contains requirements to demonstrate that radio equipment both effectively uses and supports the
efficient use of radio spectrum in order to avoid harmful interference.
The present document covers the essential requirements of article 3.2 of Directive 2014/53/EU [i.2] under the
conditions identified in annex A.

Celična omrežja IMT - Harmonizirani standard, ki zajema bistvene zahteve člena 3.2 direktive 2014/53/EU - 2. del: CDMA z neposrednim razprševanjem (“Direct Spread”) (UTRA FDD) (UE)

Ta dokument zajema zahteve za uporabniško opremo UTRA FDD iz izdaj 99, 4, 5, 6, 7, 8, 9, 10 in 11 dokumenta 3GPP™, kot je določeno v dokumentu ETSI TS 125 101 [4]. To vključuje zahteve za pasove uporabniške opreme iz izdaje 12 dokumenta 3GPP™,
ki so opredeljene v dokumentu ETSI TS 125 101 [4]. Poleg tega ta dokument zajema zahteve za uporabniško opremo UTRA FDD, ki deluje v frekvenčnih pasovih, določenih v dokumentu ETSI TS 102 735 [i.4].
OPOMBA: Za pas XX:
– Za uporabniško opremo, zasnovano kot mobilno ali nomadsko, so zahteve iz tega dokumenta, izmerjene na antenskem vhodu, tudi v skladu z ustrezno zahtevo, opredeljeno kot TRP (skupna sevana moč), kot je opisana v Sklepu Komisije 2010/267/EU [i.6]
Sklepu Odbora za elektronske komunikacije (09)03 [i.7] in poročilu CEPT 30 [i.8].
- Za uporabniško opremo, zasnovano za priključitev ali namestitev, ta dokument ne obravnava zahtev, opisanih v Sklepu Komisije 2010/267/EU [i.6], Sklepu Odbora za elektronske komunikacije (09)03 [i.7] in poročilu CEPT 30 [i.8].
Ta dokument vsebuje zahteve, s katerimi se dokazuje, da je radijska oprema izdelana tako, da učinkovito uporablja in podpira učinkovito rabo radijskega spektra z namenom preprečevanja škodljivega motenja.
Ta dokument zajema bistvene zahteve člena 3.2 direktive 2014/53/EU [i.2] pod pogoji iz dodatka A.

General Information

• Status: Published
• Publication Date: 22-Aug-2017
• ICS: 33.060.99 - Other equipment for radiocommunications
• ICS: 33.070.99 - Other mobile services
• Technical Committee: MOC - Mobile Communications
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 17-Aug-2017
• Due Date: 22-Oct-2017
• Completion Date: 23-Aug-2017
• Directive: 2014/53/EU - Directive 2014/53/EU of The European Parliament and of the Council of 16 April 2014 on the harmonisation of the laws of the Member States relating to the making available on the market of radio equipment and repealing Directive 1999/5/EC
• Ref Project: ETSI EN 301 908-2 V11.1.2 (2017-08) - IMT cellular networks; Harmonised Standard covering the essential requirements of article 3.2 of Directive 2014/53/EU; Part 2: CDMA Direct Spread (UTRA FDD) User Equipment (UE)

Standards Content (Sample)

HARMONISED EUROPEAN STANDARD
IMT cellular networks;
Harmonised Standard covering the essential requirements
of article 3.2 of Directive 2014/53/EU;
Part 2: CDMA Direct Spread (UTRA FDD)
User Equipment (UE)
2 ETSI EN 301 908-2 V11.1.2 (2017-08)

Reference
REN/MSG-TFES-11-02-RED-C1
Keywords
3G, 3GPP, cellular, digital, IMT, mobile, radio,
regulation, UMTS, UTRA, WCDMA
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: [phone]  Fax: [phone]

Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88

Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.

© ETSI 2017.
All rights reserved.
TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are trademarks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are trademarks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
oneM2M logo is protected for the benefit of its Members.
GSM® and the GSM logo are trademarks registered and owned by the GSM Association.
ETSI
3 ETSI EN 301 908-2 V11.1.2 (2017-08)
Contents
Intellectual Property Rights . 7
Foreword . 7
Modal verbs terminology . 7
Introduction . 8
1 Scope . 9
2 References . 10
2.1 Normative references . 10
2.2 Informative references . 10
3 Definitions, symbols and abbreviations . 11
3.1 Definitions . 11
3.2 Symbols . 12
3.3 Abbreviations . 13
4 Technical requirements specifications . 14
4.1 Environmental profile . 14
4.2 Conformance requirements . 14
4.2.0 General . 14
4.2.1 Introduction. 14
4.2.2 Transmitter maximum output power. 15
4.2.2.1 Transmitter maximum output power . 15
4.2.2.1.1 Definition. 15
4.2.2.1.2 Limits . 15
4.2.2.1.3 Conformance . 16
4.2.2.2 Transmitter maximum output power for DC-HSUPA . 16
4.2.2.2.1 Definition for DC-HSUPA . 16
4.2.2.2.2 Limits for DC-HSUPA . 16
4.2.2.2.3 Conformance . 16
4.2.2.3 Transmitter maximum output power for UL OLTD . 16
4.2.2.3.1 Definition for UL OLTD . 16
4.2.2.3.2 Limits for UL OLTD . 16
4.2.2.3.3 Conformance . 17
4.2.3 Transmitter spectrum emission mask . 17
4.2.3.1 Transmitter spectrum emission mask . 17
4.2.3.1.1 Definition. 17
4.2.3.1.2 Limits . 17
4.2.3.1.3 Conformance . 18
4.2.3.2 Transmitter spectrum emission mask for DC-HSUPA . 18
4.2.3.2.1 Definition for DC-HSUPA . 18
4.2.3.2.2 Limits for DC-HSUPA . 18
4.2.3.2.3 Conformance . 18
4.2.3.3 Transmitter spectrum emission mask for UL OLTD . 19
4.2.3.3.1 Definition for UL OLTD . 19
4.2.3.3.2 Limits for UL OLTD . 19
4.2.3.3.3 Conformance . 19
4.2.3.4 Transmitter spectrum emission mask for UL CLTD Activation state 1 . 19
4.2.3.4.1 Definition for UL CLTD Activation state 1 . 19
4.2.3.4.2 Limits for UL CLTD Activation state 1 . 19
4.2.3.4.3 Conformance . 20
4.2.4 Transmitter spurious emis sions . 20
4.2.4.1 Transmitter spurious emissions . 20
4.2.4.1.1 Definition. 20
4.2.4.1.2 Limits . 20
4.2.4.1.3 Conformance . 22
4.2.4.2 Transmitter spurious emissions for DC-HSUPA . 22
4.2.4.2.1 Definition for DC-HSUPA . 22
ETSI
4 ETSI EN 301 908-2 V11.1.2 (2017-08)
4.2.4.2.2 Limits for DC-HSUPA . 22
4.2.4.2.3 Conformance . 24
4.2.5 Transmitter minimum output power . 25
4.2.5.1 Transmitter minimum output power. 25
4.2.5.1.1 Definition. 25
4.2.5.1.2 Limits . 25
4.2.5.1.3 Conformance . 25
4.2.5.2 Transmitter minimum output power for DC-HSUPA . 25
4.2.5.2.1 Definition for DC-HSUPA . 25
4.2.5.2.2 Limits for DC-HSUPA . 25
4.2.5.2.3 Conformance . 25
4.2.5.3 Transmitter minimum output power for UL CLTD Activation state 1 . 25
4.2.5.3.1 Definition for UL CLTD Activation state 1 . 25
4.2.5.3.2 Limits for UL CLTD Activation state 1 . 25
4.2.5.3.3 Conformance . 25
4.2.6 Receiver Adjacent Channel Selectivity (ACS) . 26
4.2.6.1 Definition . 26
4.2.6.2 Limits . 26
4.2.6.3 Conformance . 26
4.2.7 Receiver blocking characteristics . 26
4.2.7.1 Definition . 26
4.2.7.2 Limits . 26
4.2.7.3 Conformance . 28
4.2.8 Receiver spurious response . 28
4.2.8.1 Definition . 28
4.2.8.2 Limits . 28
4.2.8.3 Conformance . 29
4.2.9 Receiver intermodulation characteristics . 29
4.2.9.1 Definition . 29
4.2.9.2 Limits . 29
4.2.9.3 Conformance . 30
4.2.10 Receiver spurious emissions . 30
4.2.10.1 Definition . 30
4.2.10.2 Limits . 30
4.2.10.3 Conformance . 31
4.2.11 Out-of-synchronization handling of output power . 31
4.2.11.1 Definition . 31
4.2.11.2 Limits . 31
4.2.11.3 Conformance . 33
4.2.12 Transmitter Adjacent Channel Leakage power Ratio (ACLR) . 33
4.2.12.1 Transmitter adjacent channel leakage power ratio (ACLR) . 33
4.2.12.1.1 Definition. 33
4.2.12.1.2 Limits . 33
4.2.12.1.3 Conformance . 33
4.2.12.2 Adjacent channel leakage power ratio for DC-HSUPA . 33
4.2.12.2.1 Definition for DC-HSUPA . 33
4.2.12.2.2 Limits for DC-HSUPA . 33
4.2.12.2.3 Conformance . 34
4.2.12.3 Adjacent channel leakage power ratio for UL OLTD . 34
4.2.12.3.1 Definition for UL OLTD . 34
4.2.12.3.2 Limits for UL OLTD . 34
4.2.12.3.3 Conformance . 34
4.2.12.4 Adjacent channel leakage power ratio for UL CLTD Activation state 1 . 34
4.2.12.4.1 Definition for UL CLTD Activation state 1 . 34
4.2.12.4.2 Limits for UL CLTD Activation state 1 . 34
4.2.12.4.3 Conformance . 35
4.2.13 Receiver Reference Sensitivity level . 35
4.2.13.0 General . 35
4.2.13.1 Definition . 35
4.2.13.2 Limits . 35
4.2.13.3 Conformance . 35
ETSI
5 ETSI EN 301 908-2 V11.1.2 (2017-08)
5 Testing for compliance with technical requirements . 35
5.1 Environmental conditions for testing . 35
5.2 Interpretation of the measurement results . 36
5.3 Essential radio test suites . 37
5.3.0 General . 37
5.3.1 Transmitter maximum output power. 37
5.3.1.1 Method of test . 37
5.3.1.1.1 UTRA . 37
5.3.1.1.1A DC-HSUPA . 38
5.3.1.1.1B UL OLTD . 38
5.3.1.2 Test requirements . 39
5.3.2 Transmitter spectrum emission mask . 39
5.3.2.1 Method of test . 39
5.3.2.1.1 UEs not supporting HSDPA and/or E-DCH . 39
5.3.2.1.1A UEs supporting HSDPA and/or E-DCH . 40
5.3.2.1.1B DC-HSUPA . 40
5.3.2.1.1C UL OLTD . 41
5.3.2.1.1D UL CLTD Activation state 1 . 42
5.3.2.2 Test requirements . 42
5.3.3 Transmitter spurious emis sions . 42
5.3.3.1 Method of test . 42
5.3.3.1.1 UTRA . 42
5.3.3.1.1A DC-HSUPA . 43
5.3.3.2 Test requirements . 43
5.3.4 Transmitter minimum output power . 44
5.3.4.1 Method of test . 44
5.3.4.1.1 UTRA . 44
5.3.4.1.1A DC-HSUPA . 44
5.3.4.1.1B UL CLTD Activation state 1 . 45
5.3.4.2 Test requirements . 45
5.3.5 Receiver Adjacent Channel Selectivity (ACS) . 45
5.3.5.1 Method of test . 45
5.3.5.1.1 Initial conditions . 45
5.3.5.1.2 Procedure . 46
5.3.5.2 Test requirements . 46
5.3.6 Receiver blocking characteristics . 46
5.3.6.1 Method of test . 46
5.3.6.1.1 Initial requirements . 46
5.3.6.1.2 Procedure . 46
5.3.6.2 Test requirements . 46
5.3.7 Receiver spurious response . 47
5.3.7.1 Method of test . 47
5.3.7.1.1 Initial conditions . 47
5.3.7.1.2 Procedure . 47
5.3.7.2 Test requirements . 47
5.3.8 Receiver Intermodulation characteristics . 47
5.3.8.1 Method of test . 47
5.3.8.1.1 Initial conditions . 47
5.3.8.1.2 Procedure . 48
5.3.8.2 Test requirements . 48
5.3.9 Receiver spurious emissions . 48
5.3.9.1 Method of test . 48
5.3.9.1.1 Initial conditions . 48
5.3.9.1.2 Procedure . 48
5.3.9.2 Test requirements . 48
5.3.10 Out-of-synchronization handling of output power . 48
5.3.10.1 Method of test . 48
5.3.10.1.1 Initial conditions . 48
5.3.10.1.2 Procedure . 49
5.3.10.2 Test requirements . 49
5.3.11 Transmitter adjacent channel leakage power ratio . 49
5.3.11.1 Method of test . 49
ETSI
6 ETSI EN 301 908-2 V11.1.2 (2017-08)
5.3.11.1.1 UEs not supporting HSDPA and/or E-DCH . 49
5.3.11.1.1A UEs supporting HSDPA and/or E-DCH . 50
5.3.11.1.1B DC-HSUPA . 50
5.3.11.1.1C UL OLTD . 51
5.3.11.1.1D UL CLTD Activation state 1 . 51
5.3.11.2 Test requirements . 52
5.3.12 Receiver Reference Sensitivity level . 52
5.3.12.1 Method of test . 52
5.3.12.1.1 Initial conditions . 52
5.3.12.1.2 Procedure . 52
5.3.12.2 Test requirements . 52
Annex A (informative): Relationship between the present document and the essential
requirements of Directive 2014/53/EU . 53
Annex B (normative): Environmental profile . 54
B.1 General . 54
B.1.1 Introduction . 54
B.1.2 Temperature . 54
B.1.3 Voltage . 54
B.1.4 Test environment . 54
Annex C (informative): Bibliography . 55
Annex D (informative): Change history . 56
History . 57

ETSI
7 ETSI EN 301 908-2 V11.1.2 (2017-08)
Intellectual Property Rights
Essential patents
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Trademarks
The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.
ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no
right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does
not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.
Foreword
This Harmonised European Standard (EN) has been produced by ETSI Technical Committee Mobile Standards Group
(MSG).
The present document has been prepared under the Commission's standardisation request C(2015) 5376 final [i.9] to
provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation
of the laws of the Member States relating to the making available on the market of radio equipment and repealing
Directive 1999/5/EC [i.2].
Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with
the normative clauses of the present document given in table A-1 confers, within the limits of the scope of the present
document, a presumption of conformity with the corresponding essential requirements of that Directive, and associated
EFTA regulations.
The present document is part 2 of a multi-part deliverable. Full details of the entire series can be found in part 1 [i.10].

National transposition dates
Date of latest announcement of this EN (doa): 30 November 2017
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 31 May 2018
Date of withdrawal of any conflicting National Standard (dow): 31 May 2019

Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
ETSI
8 ETSI EN 301 908-2 V11.1.2 (2017-08)
Introduction
The present document is part of a set of standards developed by ETSI and is designed to fit in a modular structure to
cover all radio and telecommunications terminal equipment within the scope of the Radio Equipment Directive [i.2].
The present document is produced following the guidance in ETSI EG 203 336 [i.3] as applicable.

ETSI
9 ETSI EN 301 908-2 V11.1.2 (2017-08)
1 Scope
The present document applies to the following radio equipment type:
• User Equipment for IMT-2000 CDMA Direct Spread (UTRA FDD).
These radio equipment types are capable of operating in all or any part of the frequency bands given in table 1-1.
Table 1-1: UTRA FDD operating bands
UTRA FDD Band Direction of transmission UTRA FDD operating bands
I Transmit 1 920 MHz to 1 980 MHz
Receive 2 110 MHz to 2 170 MHz
III Transmit 1 710 MHz to 1 785 MHz
Receive 1 805 MHz to 1 880 MHz
VII Transmit 2 500 MHz to 2 570 MHz
Receive 2 620 MHz to 2 690 MHz
VIII Transmit 880 MHz to 915 MHz
Receive 925 MHz to 960 MHz
XV Transmit 1 900 MHz to 1 920 MHz
Receive 2 600 MHz to 2 620 MHz
XVI Transmit 2 010 MHz to 2 025 MHz
Receive 2 585 MHz to 2 600 MHz
XX Transmit 832 MHz to 862 MHz
Receive 791 MHz to 821 MHz
XXII Transmit 3 410 MHz to 3 490 MHz
Receive 3 510 MHz to 3 590 MHz

The present document covers requirements for UTRA FDD User Equipment from 3GPP™ Releases 99, 4, 5, 6, 7, 8, 9,
10 and 11 defined in ETSI TS 125 101 [4]. This include the requirements for UE operating bands from 3GPP™
Release 12 defined in ETSI TS 125 101 [4]. In addition, the present document covers requirements for UTRA FDD
User Equipment in the operating bands specified in ETSI TS 102 735 [i.4].
NOTE: For Band XX:
- for user equipment designed to be mobile or nomadic, the requirements in the present document
measured at the antenna port also show conformity to the corresponding requirement defined as
TRP (Total Radiated Power), as described in Commission Decision 2010/267/EU [i.6],
ECC Decision (09)03 [i.7] and CEPT Report 30 [i.8];
- for user equipment designed to be fixed or installed, the present document does not address the
requirements described in Commission Decision 2010/267/EU [i.6], ECC Decision (09)03 [i.7] and
CEPT Report 30 [i.8].
The present document contains requirements to demonstrate that radio equipment both effectively uses and supports the
efficient use of radio spectrum in order to avoid harmful interference.
The present document covers the essential requirements of article 3.2 of Directive 2014/53/EU [i.2] under the
conditions identified in annex A.
ETSI
10 ETSI EN 301 908-2 V11.1.2 (2017-08)
2 References
2.1 Normative references
References are specific, identified by date of publication and/or edition number or version number. Only the cited
version applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
http://docbox.etsi.org/Reference.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are necessary for the application of the present document.
[1] ETSI TS 134 121-1 (V12.1.0) (10-2015): "Universal Mobile Telecommunications System
(UMTS); User Equipment (UE) conformance specification; Radio transmission and reception
(FDD); Part 1: Conformance specification (3GPP TS 34.121-1 version 12.1.0 Release 12)".
[2] ETSI TS 134 108 (V12.1.0) (10-2015): "Universal Mobile Telecommunications System (UMTS);
LTE; Common test environments for User Equipment (UE); Conformance testing (3GPP
TS 34.108 version 12.1.0 Release 12)".
[3] ETSI TS 134 109 (V12.0.0) (09-2014): "Universal Mobile Telecommunications System (UMTS);
Terminal logical test interface; Special conformance testing functions (3GPP TS 34.109
version 12.0.0 Release 12)".
[4] ETSI TS 125 101 (V11.11.0) (01-2015): "Universal Mobile Telecommunications System (UMTS);
User Equipment (UE) radio transmission and reception (FDD) (3GPP TS 25.101 version 11.11.0
Release 11)".
[5] IEC 60068-2-1 (03-2007): "Environmental testing - Part 2-1: Tests - Test A: Cold".
[6] IEC 60068-2-2 (07-2007): "Environmental testing - Part 2-2: Tests - Test B: Dry heat".
[7] ETSI TS 125 214 (V11.12.0) (07-2015): "Universal Mobile Telecommunications System (UMTS);
Physical layer procedures (FDD) (3GPP TS 25.214 version 11.12.0 Release 11)".
[8] ETSI TS 145 004 (V11.0.0) (10-2012): "Digital cellular telecommunications system (Phase 2+);
Modulation (3GPP TS 45.004 version 11.0.0 Release 11)".
2.2 Informative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are not necessary for the application of the present document but they assist the
user with regard to a particular subject area.
[i.1] Void.
[i.2] Directive 2014/53/EU of the European Parliament and of the Council of 16 April 2014 on the
harmonisation of the laws of the Member States relating to the making available on the market of
radio equipment and repealing Directive 1999/5/EC.
[i.3] ETSI EG 203 336 (V1.1.1) (08-2015): "Electromagnetic compatibility and Radio spectrum
Matters (ERM); Guide for the selection of technical parameters for the production of Harmonised
Standards covering article 3.1(b) and article 3.2 of Directive 2014/53/EU".
ETSI
11 ETSI EN 301 908-2 V11.1.2 (2017-08)
[i.4] ETSI TS 102 735 (V7.1.0): "Universal Mobile Telecommunications System (UMTS); Band-
specific requirements for UMTS Frequency Division Duplex (FDD) operation in the bands
1 900 MHz to 1 920 MHz paired with 2 600 MHz to 2 620 MHz and 2 010 MHz to 2 025 MHz
paired with 2 585 MHz to 2 600 MHz".
[i.5] ETSI TR 100 028 (all parts) (V1.4.1): "Electromagnetic compatibility and Radio spectrum Matters
(ERM); Uncertainties in the measurement of mobile radio equipment characteristics".
[i.6] Commission Decision 2010/267/EU of 6 May 2010 on harmonised technical conditions of use in
the 790-862 MHz frequency band for terrestrial systems capable of providing electronic
communications services in the European Union.
[i.7] ECC Decision (09)03 of 30 October 2009 on harmonised conditions for mobile/fixed
communications networks (MFCN) operating in the band 790 - 862 MHz.
[i.8] CEPT Report 30 of 30 October 2009 to the European Commission in response to the Mandate on
"The identification of common and minimal (least restrictive) technical conditions for
790 - 862 MHz for the digital dividend in the European Union".
[i.9] Commission Implementing Decision C(2015) 5376 final of 4.8.2015 on a standardisation request
to the European Committee for Electrotechnical Standardisation and to the European
Telecommunications Standards Institute as regards radio equipment in support of Directive
2014/53/EU of the European Parliament and of the Council.
[i.10] ETSI EN 301 908-1 (V11.1.1): "IMT cellular networks; Harmonised Standard covering the
essential requirements of article 3.2 of the Directive 2014/53/EU; Part 1: Introduction and
common requirements".
3 Definitions, symbols and abbreviations
3.1 Definitions
For the purposes of the present document, the following terms and definit
...

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.IMT cellular networks - Harmonised Standard covering the essential requirements of article 3.2 of Directive 2014/53/EU - Part 2: CDMA Direct Spread (UTRA FDD) User Equipment (UE)33.070.99Druge mobilne storitveOther mobile services33.060.99Druga oprema za radijske komunikacijeOther equipment for radiocommunicationsICS:Ta slovenski standard je istoveten z:ETSI EN 301 908-2 V11.1.2 (2017-08)SIST EN 301 908-2 V11.1.2:2017en01-oktober-2017SIST EN 301 908-2 V11.1.2:2017SLOVENSKI
STANDARD
HARMONISED EUROPEAN STANDARD SIST EN 301 908-2 V11.1.2:2017

ETSI ETSI EN 301 908-2 V11.1.2 (2017-08)2
Reference REN/MSG-TFES-11-02-RED-C1 Keywords 3G, 3GPP, cellular, digital, IMT, mobile, radio, regulation, UMTS, UTRA, WCDMA ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: [phone]
Fax: [phone]
Siret N° 348 623 562 00017 - NAF 742 C Association à but non lucratif enregistrée à la Sous-Préfecture de Grasse (06) N° 7803/88
Important notice The present document can be downloaded from: http://www.etsi.org/standards-search The present document may be made available in electronic versions and/or in print. The content of any electronic and/or print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx If you find errors in the present document, please send your comment to one of the following services: https://portal.etsi.org/People/CommiteeSupportStaff.aspx Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm except as authorized by written permission of ETSI. The content of the PDF version shall not be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2017. All rights reserved.
DECTTM, PLUGTESTSTM, UMTSTM and the ETSI logo are trademarks of ETSI registered for the benefit of its Members. 3GPPTM and LTE™ are trademarks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. oneM2M logo is protected for the benefit of its Members. GSM® and the GSM logo are trademarks registered and owned by the GSM Association. SIST EN 301 908-2 V11.1.2:2017

ETSI ETSI EN 301 908-2 V11.1.2 (2017-08)3 Contents Intellectual Property Rights . 7 Foreword . 7 Modal verbs terminology . 7 Introduction . 8 1 Scope . 9 2 References . 10 2.1 Normative references . 10 2.2 Informative references . 10 3 Definitions, symbols and abbreviations . 11 3.1 Definitions . 11 3.2 Symbols . 12 3.3 Abbreviations . 13 4 Technical requirements specifications . 14 4.1 Environmental profile . 14 4.2 Conformance requirements . 14 4.2.0 General . 14 4.2.1 Introduction. 14 4.2.2 Transmitter maximum output power. 15 4.2.2.1 Transmitter maximum output power . 15 4.2.2.1.1 Definition. 15 4.2.2.1.2 Limits . 15 4.2.2.1.3 Conformance . 16 4.2.2.2 Transmitter maximum output power for DC-HSUPA . 16 4.2.2.2.1 Definition for DC-HSUPA . 16 4.2.2.2.2 Limits for DC-HSUPA . 16 4.2.2.2.3 Conformance . 16 4.2.2.3 Transmitter maximum output power for UL OLTD . 16 4.2.2.3.1 Definition for UL OLTD . 16 4.2.2.3.2 Limits for UL OLTD . 16 4.2.2.3.3 Conformance . 17 4.2.3 Transmitter spectrum emission mask . 17 4.2.3.1 Transmitter spectrum emission mask . 17 4.2.3.1.1 Definition. 17 4.2.3.1.2 Limits . 17 4.2.3.1.3 Conformance . 18 4.2.3.2 Transmitter spectrum emission mask for DC-HSUPA . 18 4.2.3.2.1 Definition for DC-HSUPA . 18 4.2.3.2.2 Limits for DC-HSUPA . 18 4.2.3.2.3 Conformance . 18 4.2.3.3 Transmitter spectrum emission mask for UL OLTD . 19 4.2.3.3.1 Definition for UL OLTD . 19 4.2.3.3.2 Limits for UL OLTD . 19 4.2.3.3.3 Conformance . 19 4.2.3.4 Transmitter spectrum emission mask for UL CLTD Activation state 1 . 19 4.2.3.4.1 Definition for UL CLTD Activation state 1 . 19 4.2.3.4.2 Limits for UL CLTD Activation state 1 . 19 4.2.3.4.3 Conformance . 20 4.2.4 Transmitter spurious emissions . 20 4.2.4.1 Transmitter spurious emissions . 20 4.2.4.1.1 Definition. 20 4.2.4.1.2 Limits . 20 4.2.4.1.3 Conformance . 22 4.2.4.2 Transmitter spurious emissions for DC-HSUPA . 22 4.2.4.2.1 Definition for DC-HSUPA . 22 SIST EN 301 908-2 V11.1.2:2017

ETSI ETSI EN 301 908-2 V11.1.2 (2017-08)4 4.2.4.2.2 Limits for DC-HSUPA . 22 4.2.4.2.3 Conformance . 24 4.2.5 Transmitter minimum output power . 25 4.2.5.1 Transmitter minimum output power. 25 4.2.5.1.1 Definition. 25 4.2.5.1.2 Limits . 25 4.2.5.1.3 Conformance . 25 4.2.5.2 Transmitter minimum output power for DC-HSUPA . 25 4.2.5.2.1 Definition for DC-HSUPA . 25 4.2.5.2.2 Limits for DC-HSUPA . 25 4.2.5.2.3 Conformance . 25 4.2.5.3 Transmitter minimum output power for UL CLTD Activation state 1 . 25 4.2.5.3.1 Definition for UL CLTD Activation state 1 . 25 4.2.5.3.2 Limits for UL CLTD Activation state 1 . 25 4.2.5.3.3 Conformance . 25 4.2.6 Receiver Adjacent Channel Selectivity (ACS) . 26 4.2.6.1 Definition . 26 4.2.6.2 Limits . 26 4.2.6.3 Conformance . 26 4.2.7 Receiver blocking characteristics . 26 4.2.7.1 Definition . 26 4.2.7.2 Limits . 26 4.2.7.3 Conformance . 28 4.2.8 Receiver spurious response . 28 4.2.8.1 Definition . 28 4.2.8.2 Limits . 28 4.2.8.3 Conformance . 29 4.2.9 Receiver intermodulation characteristics . 29 4.2.9.1 Definition . 29 4.2.9.2 Limits . 29 4.2.9.3 Conformance . 30 4.2.10 Receiver spurious emissions . 30 4.2.10.1 Definition . 30 4.2.10.2 Limits . 30 4.2.10.3 Conformance . 31 4.2.11 Out-of-synchronization handling of output power . 31 4.2.11.1 Definition . 31 4.2.11.2 Limits . 31 4.2.11.3 Conformance . 33 4.2.12 Transmitter Adjacent Channel Leakage power Ratio (ACLR) . 33 4.2.12.1 Transmitter adjacent channel leakage power ratio (ACLR) . 33 4.2.12.1.1 Definition. 33 4.2.12.1.2 Limits . 33 4.2.12.1.3 Conformance . 33 4.2.12.2 Adjacent channel leakage power ratio for DC-HSUPA . 33 4.2.12.2.1 Definition for DC-HSUPA . 33 4.2.12.2.2 Limits for DC-HSUPA . 33 4.2.12.2.3 Conformance . 34 4.2.12.3 Adjacent channel leakage power ratio for UL OLTD . 34 4.2.12.3.1 Definition for UL OLTD . 34 4.2.12.3.2 Limits for UL OLTD . 34 4.2.12.3.3 Conformance . 34 4.2.12.4 Adjacent channel leakage power ratio for UL CLTD Activation state 1 . 34 4.2.12.4.1 Definition for UL CLTD Activation state 1 . 34 4.2.12.4.2 Limits for UL CLTD Activation state 1 . 34 4.2.12.4.3 Conformance . 35 4.2.13 Receiver Reference Sensitivity level . 35 4.2.13.0 General . 35 4.2.13.1 Definition . 35 4.2.13.2 Limits . 35 4.2.13.3 Conformance . 35 SIST EN 301 908-2 V11.1.2:2017

ETSI ETSI EN 301 908-2 V11.1.2 (2017-08)5 5 Testing for compliance with technical requirements . 35 5.1 Environmental conditions for testing . 35 5.2 Interpretation of the measurement results . 36 5.3 Essential radio test suites . 37 5.3.0 General . 37 5.3.1 Transmitter maximum output power. 37 5.3.1.1 Method of test . 37 5.3.1.1.1 UTRA . 37 5.3.1.1.1A DC-HSUPA . 38 5.3.1.1.1B UL OLTD . 38 5.3.1.2 Test requirements . 39 5.3.2 Transmitter spectrum emission mask . 39 5.3.2.1 Method of test . 39 5.3.2.1.1 UEs not supporting HSDPA and/or E-DCH . 39 5.3.2.1.1A UEs supporting HSDPA and/or E-DCH . 40 5.3.2.1.1B DC-HSUPA . 40 5.3.2.1.1C UL OLTD . 41 5.3.2.1.1D UL CLTD Activation state 1 . 42 5.3.2.2 Test requirements . 42 5.3.3 Transmitter spurious emissions . 42 5.3.3.1 Method of test . 42 5.3.3.1.1 UTRA . 42 5.3.3.1.1A DC-HSUPA . 43 5.3.3.2 Test requirements . 43 5.3.4 Transmitter minimum output power . 44 5.3.4.1 Method of test . 44 5.3.4.1.1 UTRA . 44 5.3.4.1.1A DC-HSUPA . 44 5.3.4.1.1B UL CLTD Activation state 1 . 45 5.3.4.2 Test requirements . 45 5.3.5 Receiver Adjacent Channel Selectivity (ACS) . 45 5.3.5.1 Method of test . 45 5.3.5.1.1 Initial conditions . 45 5.3.5.1.2 Procedure . 46 5.3.5.2 Test requirements . 46 5.3.6 Receiver blocking characteristics . 46 5.3.6.1 Method of test . 46 5.3.6.1.1 Initial requirements . 46 5.3.6.1.2 Procedure . 46 5.3.6.2 Test requirements . 46 5.3.7 Receiver spurious response . 47 5.3.7.1 Method of test . 47 5.3.7.1.1 Initial conditions . 47 5.3.7.1.2 Procedure . 47 5.3.7.2 Test requirements . 47 5.3.8 Receiver Intermodulation characteristics . 47 5.3.8.1 Method of test . 47 5.3.8.1.1 Initial conditions . 47 5.3.8.1.2 Procedure . 48 5.3.8.2 Test requirements . 48 5.3.9 Receiver spurious emissions . 48 5.3.9.1 Method of test . 48 5.3.9.1.1 Initial conditions . 48 5.3.9.1.2 Procedure . 48 5.3.9.2 Test requirements . 48 5.3.10 Out-of-synchronization handling of output power . 48 5.3.10.1 Method of test . 48 5.3.10.1.1 Initial conditions . 48 5.3.10.1.2 Procedure . 49 5.3.10.2 Test requirements . 49 5.3.11 Transmitter adjacent channel leakage power ratio . 49 5.3.11.1 Method of test . 49 SIST EN 301 908-2 V11.1.2:2017

ETSI ETSI EN 301 908-2 V11.1.2 (2017-08)6 5.3.11.1.1 UEs not supporting HSDPA and/or E-DCH . 49 5.3.11.1.1A UEs supporting HSDPA and/or E-DCH . 50 5.3.11.1.1B DC-HSUPA . 50 5.3.11.1.1C UL OLTD . 51 5.3.11.1.1D UL CLTD Activation state 1 . 51 5.3.11.2 Test requirements . 52 5.3.12 Receiver Reference Sensitivity level . 52 5.3.12.1 Method of test . 52 5.3.12.1.1 Initial conditions . 52 5.3.12.1.2 Procedure . 52 5.3.12.2 Test requirements . 52 Annex A (informative): Relationship between the present document and the essential requirements of Directive 2014/53/EU . 53 Annex B (normative): Environmental profile . 54 B.1 General . 54 B.1.1 Introduction . 54 B.1.2 Temperature . 54 B.1.3 Voltage . 54 B.1.4 Test environment . 54 Annex C (informative): Bibliography . 55 Annex D (informative): Change history . 56 History . 57
ETSI ETSI EN 301 908-2 V11.1.2 (2017-08)7 Intellectual Property Rights Essential patents IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (https://ipr.etsi.org/). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Trademarks The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners. ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks. Foreword This Harmonised European Standard (EN) has been produced by ETSI Technical Committee Mobile Standards Group (MSG). The present document has been prepared under the Commission's standardisation request C(2015) 5376 final [i.9] to provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation of the laws of the Member States relating to the making available on the market of radio equipment and repealing Directive 1999/5/EC [i.2]. Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with the normative clauses of the present document given in table A-1 confers, within the limits of the scope of the present document, a presumption of conformity with the corresponding essential requirements of that Directive, and associated EFTA regulations. The present document is part 2 of a multi-part deliverable. Full details of the entire series can be found in part 1 [i.10].
National transposition dates Date of latest announcement of this EN (doa): 30 November 2017 Date of latest publication of new National Standard or endorsement of this EN (dop/e):
31 May 2018 Date of withdrawal of any conflicting National Standard (dow): 31 May 2019
Modal verbs terminology In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and "cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of provisions). "must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation. SIST EN 301 908-2 V11.1.2:2017

ETSI ETSI EN 301 908-2 V11.1.2 (2017-08)8 Introduction The present document is part of a set of standards developed by ETSI and is designed to fit in a modular structure to cover all radio and telecommunications terminal equipment within the scope of the Radio Equipment Directive [i.2]. The present document is produced following the guidance in ETSI EG 203 336 [i.3] as applicable.
ETSI ETSI EN 301 908-2 V11.1.2 (2017-08)9 1 Scope The present document applies to the following radio equipment type: • User Equipment for IMT-2000 CDMA Direct Spread (UTRA FDD). These radio equipment types are capable of operating in all or any part of the frequency bands given in table 1-1. Table 1-1: UTRA FDD operating bands UTRA FDD Band Direction of transmission UTRA FDD operating bands I Transmit 1 920 MHz to 1 980 MHz Receive 2 110 MHz to 2 170 MHz III Transmit 1 710 MHz to 1 785 MHz Receive 1 805 MHz to 1 880 MHz VII Transmit 2 500 MHz to 2 570 MHz Receive 2 620 MHz to 2 690 MHz VIII Transmit 880 MHz to 915 MHz Receive 925 MHz to 960 MHz XV Transmit 1 900 MHz to 1 920 MHz Receive 2 600 MHz to 2 620 MHz XVI Transmit 2 010 MHz to 2 025 MHz Receive 2 585 MHz to 2 600 MHz XX Transmit 832 MHz to 862 MHz Receive 791 MHz to 821 MHz XXII Transmit 3 410 MHz to 3 490 MHz Receive 3 510 MHz to 3 590 MHz
The present document covers requirements for UTRA FDD User Equipment from 3GPP™ Releases 99, 4, 5, 6, 7, 8, 9, 10 and 11 defined in ETSI TS 125 101 [4]. This include the requirements for UE operating bands from 3GPP™ Release 12 defined in ETSI TS 125 101 [4]. In addition, the present document covers requirements for UTRA FDD User Equipment in the operating bands specified in ETSI TS 102 735 [i.4]. NOTE: For Band XX: - for user equipment designed to be mobile or nomadic, the requirements in the present document measured at the antenna port also show conformity to the corresponding requirement defined as TRP (Total Radiated Power), as described in Commission Decision 2010/267/EU [i.6],
ECC Decision (09)03 [i.7] and CEPT Report 30 [i.8]; - for user equipment designed to be fixed or installed, the present document does not address the requirements described in Commission Decision 2010/267/EU [i.6], ECC Decision (09)03 [i.7] and CEPT Report 30 [i.8]. The present document contains requirements to demonstrate that radio equipment both effectively uses and supports the efficient use of radio spectrum in order to avoid harmful interference. The present document covers the essential requirements of article 3.2 of Directive 2014/53/EU [i.2] under the conditions identified in annex A. SIST EN 301 908-2 V11.1.2:2017

ETSI ETSI EN 301 908-2 V11.1.2 (2017-08)10 2 References 2.1 Normative references References are specific, identified by date of publication and/or edition number or version number. Only the cited version applies. Referenced documents which are not found to be publicly available in the expected location might be found at http://docbox.etsi.org/Reference. NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee their long term validity. The following referenced documents are necessary for the application of the present document. [1] ETSI TS 134 121-1 (V12.1.0) (10-2015): "Universal Mobile Telecommunications System (UMTS); User Equipment (UE) conformance specification; Radio transmission and reception (FDD); Part 1: Conformance specification (3GPP TS 34.121-1 version 12.1.0 Release 12)". [2] ETSI TS 134 108 (V12.1.0) (10-2015): "Universal Mobile Telecommunications System (UMTS); LTE; Common test environments for User Equipment (UE); Conformance testing (3GPP TS 34.108 version 12.1.0 Release 12)". [3] ETSI TS 134 109 (V12.0.0) (09-2014): "Universal Mobile Telecommunications System (UMTS); Terminal logical test interface; Special conformance testing functions (3GPP TS 34.109 version 12.0.0 Release 12)". [4] ETSI TS 125 101 (V11.11.0) (01-2015): "Universal Mobile Telecommunications System (UMTS); User Equipment (UE) radio transmission and reception (FDD) (3GPP TS 25.101 version 11.11.0 Release 11)". [5] IEC 60068-2-1 (03-2007): "Environmental testing - Part 2-1: Tests - Test A: Cold". [6] IEC 60068-2-2 (07-2007): "Environmental testing - Part 2-2: Tests - Test B: Dry heat". [7] ETSI TS 125 214 (V11.12.0) (07-2015): "Universal Mobile Telecommunications System (UMTS); Physical layer procedures (FDD) (3GPP TS 25.214 version 11.12.0 Release 11)". [8] ETSI TS 145 004 (V11.0.0) (10-2012): "Digital cellular telecommunications system (Phase 2+); Modulation (3GPP TS 45.004 version 11.0.0 Release 11)". 2.2 Informative references References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the referenced document (including any amendments) applies. NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee their long term validity. The following referenced documents are not necessary for the application of the present document but they assist the user with regard to a particular subject area. [i.1] Void. [i.2] Directive 2014/53/EU of the European Parliament and of the Council of 16 April 2014 on the harmonisation of the laws of the Member States relating to the making available on the market of radio equipment and repealing Directive 1999/5/EC. [i.3] ETSI EG 203 336 (V1.1.1) (08-2015): "Electromagnetic compatibility and Radio spectrum Matters (ERM); Guide for the selection of technical parameters for the production of Harmonised Standards covering article 3.1(b) and article 3.2 of Directive 2014/53/EU". SIST EN 301 908-2 V11.1.2:2017

ETSI ETSI EN 301 908-2 V11.1.2 (2017-08)11 [i.4] ETSI TS 102 735 (V7.1.0): "Universal Mobile Telecommunications System (UMTS); Band-specific requirements for UMTS Frequency Division Duplex (FDD) operation in the bands 1 900 MHz to 1 920 MHz paired with 2 600 MHz to 2 620 MHz and 2 010 MHz to 2 025 MHz paired with 2 585 MHz to 2 600 MHz". [i.5] ETSI TR 100 028 (all parts) (V1.4.1): "Electromagnetic compatibility and Radio spectrum Matters (ERM); Uncertainties in the measurement of mobile radio equipment characteristics". [i.6] Commission Decision 2010/267/EU of 6 May 2010 on harmonised technical conditions of use in the 790-862 MHz frequency band for terrestrial systems capable of providing electronic communications services in the European Union. [i.7] ECC Decision (09)03 of 30 October 2009 on harmonised conditions for mobile/fixed communications networks (MFCN) operating in the band 790 - 862 MHz. [i.8] CEPT Report 30 of 30 October 2009 to the European Commission in response to the Mandate on "The identification of common and minimal (least restrictive) technical conditions for 790 - 862 MHz for the digital dividend in the European Union". [i.9] Commission Implementing Decision C(2015) 5376 final of 4.8.2015 on a standardisation request to the European Committee for Electrotechnical Standardisation and to the European Telecommunications Standards Institute as regards radio equipment in support of Directive 2014/53/EU of the European Parliament and of the Council. [i.10] ETSI EN 301 908-1 (V11.1.1): "IMT cellular networks; Harmonised Standard covering the essential requirements of article 3.2 of the Directive 2014/53/EU; Part 1: Introduction and common requirements". 3 Definitions, symbols and abbreviations 3.1 Definitions For the purposes of the present document, the following terms and definitions apply: chip rate: rate of "chips" (modulated symbols aft
...