SIST EN IEC 61076-2-010:2021

Connectors for electrical and electronic equipment - Product requirements - Part 2-010: Circular connectors - Detail specification for connectors with outer or inner push-pull locking mechanism, based on mating interfaces according to IEC 61076-2-101, IEC 61076-2-109, IEC 61076-2-111 and IEC 61076-2-113 (IEC 61076-2-010:2021)

This part of IEC 61076-2 specifies circular connectors with a push-pull locking mechanism of a size derived from, and thus being compatible with M12 screw-locking connectors (free connectors with screw-locking according to IEC 61076‑2‑101, IEC 61076-2-109,
IEC 61076-2-111 or IEC 61076‑2‑113 are compatible with push‑pull fixed interfaces according
to this document) and with mating interfaces according to IEC 61076‑2‑101, IEC 61076-2-109,
IEC 61076-2-111 (except codings E in general and coding F for inner push-pull) or
IEC 61076-2-113.
A fixed connector with push-pull locking according to this document is intermateable with a
correspondingly coded free connector with M12 screw-locking according to any of the above
mentioned standards.
NOTE 1 M12 is the dimension of the thread of the screw-locking mechanism of circular connectors with M12 screwlocking.
NOTE 2 IEC 61076-2-012 defines another inner push-pull for fixed female connectors which is however not
compatible to the inner push-pull defined in this document. Annex C shows the different styles of female free
connectors to extend male free connectors.
This document covers both:
a) power connectors with current ratings up to 16 A and voltage ratings up to 630 V, typically
used for power supply and power applications in industrial premises, and
b) connectors for data and signal transmission with frequencies up to 500 MHz.
These connectors consist of both, fixed and free connectors, either rewirable or non-rewirable,
with M12 push-pull locking as explained above. Male connectors have round contacts from Ø
0,6 mm up to Ø 1,5 mm. In addition, the push-pull mechanisms consist of 2 different push-pull
designs:
c) An outer push-pull for male and female fixed connector, where the locking groove is placed
onto the outer cylindric surface of the housing. The outer push-pull for female fixed
connectors is made for 2 different types of male connectors. It has locking means for both
types on its outer surface.
NOTE 3 For design and dimensions see 5.3.2 and 5.3.3.
d) An inner push-pull for female fixed connectors and for male free connectors, where the
locking means are placed onto the inner cylindric surface of the housing.
NOTE 4 For design and dimensions see 5.3.4.
The different codings provided by IEC 61076-2 series detail specifications mentioned within this
document prevent the mating of accordingly coded male or female connectors to any other
similarly sized interfaces, covered by other standards and the cross-mating between the
different codings provided by any other IEC 61076-2 series detail specification mentioned within
this document.

Steckverbinder für elektrische und elektronische Einrichtungen – Produktanforderungen - Teil 2-010: Rundsteckverbinder– Bauartspezifikation für Push-pull-Steckverbinder mit äußerem Verriegelungsmechanismus, basierend auf Kontaktschnittstellen nach IEC 61076-2-101, IEC 61076-2-109, IEC 61076-2-111 und IEC 61076-2-113 (IEC 61076-2-010:2021)

Connecteurs pour équipements électriques et électroniques - Exigences de produit - Partie 2-010: Connecteurs circulaires - Spécification particulière relative aux connecteurs avec mécanisme de verrouillage de type pousser-tirer externe ou interne, basés sur des interfaces d’accouplement conformes à l’IEC 61076-2-101, l’IEC 61076-2-109, l’IEC 61076-2-111 et l’IEC 61076-2-113 (IEC 61076-2-010:2021)

IEC 61076-2-010:2021 spécifie les connecteurs circulaires pourvus d’un mécanisme de verrouillage de type pousser-tirer dont la taille est dérivée des connecteurs M12 avec verrouillage à vis (les fiches avec verrouillage à vis conformes à l’IEC 61076‑2‑101, l’IEC 61076-2-109, l’IEC 61076-2-111 ou l’IEC 61076‑2‑113 sont compatibles avec les interfaces d’embase de type pousser-tirer conformes au présent document) et d’interfaces d’accouplement conformes à l’IEC 61076‑2‑101, l’IEC 61076-2-109, l’IEC 61076-2-111 (sauf les détrompages E en général et le détrompage F pour les verrouillages internes de type pousser-tirer) ou l’IEC 61076-2-113.
Une embase avec verrouillage de type pousser-tirer conforme au présent document est accouplable avec une fiche présentant le détrompage correspondant avec un verrouillage à vis M12, conformément à l’une quelconque des normes susmentionnées.
M12 désigne la dimension du filetage du mécanisme de verrouillage à vis des connecteurs circulaires avec verrouillage à vis M12.
L’IEC 61076-2-012 définit un autre verrouillage interne de type pousser-tirer pour les embases femelles, qui n’est cependant pas compatible avec le verrouillage interne de type pousser-tirer défini dans le présent document. L’Annexe C donne les différents modèles de fiches femelles adaptables sur les fiches mâles.
Le présent document couvre à la fois:
a) les connecteurs d’alimentation avec des courants assignés allant jusqu’à 16 A et des tensions assignées allant jusqu’à 630 V, généralement employés pour des applications d’alimentation et de puissance dans des locaux industriels, et
b) les connecteurs pour les transmissions de données et de signaux avec des fréquences allant jusqu’à 500 MHz.
Ces connecteurs se composent à la fois d’embases et de fiches, démontables ou non démontables, avec un verrouillage de type pousser-tirer M12 comme expliqué précédemment. Les connecteurs mâles possèdent des contacts arrondis d’un diamètre compris entre Ø 0,6 mm et Ø 1,5 mm. De plus, les mécanismes pousser-tirer présentent 2 conceptions différentes:
c) un mécanisme pousser-tirer externe pour les embases mâle et femelle, dont la rainure de verrouillage est placée sur la surface cylindrique extérieure du boîtier. Le mécanisme pousser-tirer externe pour embases femelles est conçu pour 2 types différents de connecteurs mâles. Il possède des dispositifs de verrouillage pour ces deux types de connecteurs sur sa surface extérieure;
Pour la conception et les dimensions, voir 5.3.2 et 5.3.3.
d) un mécanisme pousser-tirer interne pour les embases femelles et les fiches mâles, dont les dispositifs de verrouillage sont placés sur la surface cylindrique intérieure du boîtier.
Pour la conception et les dimensions, voir 5.3.4.
Les différents détrompages prévus par les spécifications particulières de la série IEC 61076-2 et mentionnés dans le présent document, empêchent l’accouplement de connecteurs mâles et femelles avec de tels détrompeurs avec une quelconque autre interface de taille semblable couverte par d’autres normes, ainsi que l’accouplement croisé entre les différents détrompages prévus par une quelconque autre spécification particulière de la série IEC 61076-2 mentionnée dans le présent document.

Konektorji za električno in elektronsko opremo - Zahteve za izdelek - 2-010. del: Okrogli konektorji - Podrobna specifikacija za konektorje z zunanjim ali notranjim zaklepnim mehanizmom na osnovi vmesnikov v skladu s standardi IEC 61076-2-101, IEC 61076-2-109, IEC 61076-2-111 in IEC 61076-2-113 (IEC 61076-2-010:2021)

General Information

• Status: Published
• Publication Date: 22-Aug-2021
• ICS: 31.220.10 - Plug-and-socket devices. Connectors
• Technical Committee: I11 - Imaginarni 11
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 04-Aug-2021
• Due Date: 09-Oct-2021
• Completion Date: 23-Aug-2021
• Ref Project: EN IEC 61076-2-010:2021 - Connectors for electrical and electronic equipment - Product requirements - Part 2-010: Circular connectors - Detail specification for connectors with outer or inner push-pull locking mechanism, based on mating interfaces according to IEC 61076-2-101, IEC 61076-2-109, IEC 61076-2-111 and IEC 61076-2-113

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN IEC 61076-2-010:2021
01-september-2021
Konektorji za električno in elektronsko opremo - Zahteve za izdelek - 2-010. del:
Okrogli konektorji - Podrobna specifikacija za konektorje z zunanjim ali notranjim
zaklepnim mehanizmom na osnovi vmesnikov v skladu s standardi IEC 61076-2-
101, IEC 61076-2-109, IEC 61076-2-111 in IEC 61076-2-113 (IEC 61076-2-010:2021)
Connectors for electrical and electronic equipment - Product requirements - Part 2-010:
Circular connectors - Detail specification for connectors with outer or inner push-pull
locking mechanism, based on mating interfaces according to IEC 61076-2-101, IEC
61076-2-109, IEC 61076-2-111 and IEC 61076-2-113 (IEC 61076-2-010:2021)
Steckverbinder für elektrische und elektronische Einrichtungen – Produktanforderungen -
Teil 2-010: Rundsteckverbinder– Bauartspezifikation für Push-pull-Steckverbinder mit
äußerem Verriegelungsmechanismus, basierend auf Kontaktschnittstellen nach IEC
61076-2-101, IEC 61076-2-109, IEC 61076-2-111 und IEC 61076-2-113 (IEC 61076-2-
010:2021)
Connecteurs pour équipements électriques et électroniques - Exigences de produit -
Partie 2-010: Connecteurs circulaires - Spécification particulière relative aux connecteurs
avec mécanisme de verrouillage de type pousser-tirer externe ou interne, basés sur des
interfaces d’accouplement conformes à l’IEC 61076-2-101, l’IEC 61076-2-109, l’IEC
61076-2-111 et l’IEC 61076-2-113 (IEC 61076-2-010:2021)
Ta slovenski standard je istoveten z: EN IEC 61076-2-010:2021
ICS:
31.220.10 Vtiči in vtičnice, konektorji Plug-and-socket devices.
Connectors
SIST EN IEC 61076-2-010:2021 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN IEC 61076-2-010:2021

---------------------- Page: 2 ----------------------
SIST EN IEC 61076-2-010:2021


EUROPEAN STANDARD EN IEC 61076-2-010

NORME EUROPÉENNE

EUROPÄISCHE NORM
July 2021
ICS 31.220.10

English Version
Connectors for electrical and electronic equipment - Product
requirements - Part 2-010: Circular connectors - Detail
specification for connectors with outer or inner push-pull locking
mechanism, based on mating interfaces according to IEC 61076-
2-101, IEC 61076-2-109, IEC 61076-2-111 and IEC 61076-2-113
(IEC 61076-2-010:2021)
Connecteurs pour équipements électriques et électroniques Steckverbinder für elektrische und elektronische
- Exigences de produit - Partie 2-010: Connecteurs Einrichtungen - Produktanforderungen - Teil 2-010:
circulaires - Spécification particulière relative aux Rundsteckverbinder- Bauartspezifikation für Push-pull-
connecteurs avec mécanisme de verrouillage de type Steckverbinder mit äußerem Verriegelungsmechanismus,
pousser-tirer externe ou interne, basés sur des interfaces basierend auf Kontaktschnittstellen nach IEC 61076-2-101,
d'accouplement conformes à l'IEC 61076-2-101, l'IEC IEC 61076-2-109, IEC 61076-2-111 und IEC 61076-2-113
61076-2-109, l'IEC 61076-2-111 et l'IEC 61076-2-113 (IEC 61076-2-010:2021)
(IEC 61076-2-010:2021)
This European Standard was approved by CENELEC on 2021-07-01. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.


European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
 Ref. No. EN IEC 61076-2-010:2021 E

---------------------- Page: 3 ----------------------
SIST EN IEC 61076-2-010:2021
EN IEC 61076-2-010:2021 (E)
European foreword
The text of document 48B/2876/FDIS, future edition 1 of IEC 61076-2-010, prepared by SC 48B
“Electrical connectors” of IEC/TC 48 “Electrical connectors and mechanical structures for electrical
and electronic equipment” was submitted to the IEC-CENELEC parallel vote and approved by
CENELEC as EN IEC 61076-2-010:2021.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2022–04–01
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2024–07–01
document have to be withdrawn
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
Any feedback and questions on this document should be directed to the users’ national committee. A
complete listing of these bodies can be found on the CENELEC website.
Endorsement notice
The text of the International Standard IEC 61076-2-010:2021 was approved by CENELEC as a
European Standard without any modification.
2

---------------------- Page: 4 ----------------------
SIST EN IEC 61076-2-010:2021
EN IEC 61076-2-010:2021 (E)
Annex ZA
(normative)

Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1 Where an International Publication has been modified by common modifications, indicated by (mod), the
relevant EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available
here: www.cenelec.eu.
Publication Year Title EN/HD Year
IEC 60050-581 2008 International Electrotechnical Vocabulary - - -
Part 581: Electromechanical components
for electronic equipment
IEC 60068-1 - Environmental testing - Part 1: General EN 60068-1 -
and guidance
IEC 60512-1 - Connectors for electrical and electronic EN IEC 60512-1 -
equipment - Tests and measurements -
Part 1: Generic specification
IEC 60512-2–1 - Connectors for electronic equipment - EN 60512-2–1 -
Tests and measurements - Part 2–1:
Electrical continuity and contact resistance
tests - Test 2a: Contact resistance -
Millivolt level method
IEC 60512-3–1 - Connectors for electronic equipment - EN 60512-3–1 -
Tests and measurements - Part 3–1:
Insulation tests - Test 3a: Insulation
resistance
IEC 60512-4–1 - Connectors for electronic equipment - EN 60512-4–1 -
Tests and measurements - Part 4–1:
Voltage stress tests - Test 4a: Voltage
proof
IEC 60512-5–1 - Connectors for electronic equipment - EN 60512-5–1 -
Tests and measurements - Part 5–1:
Current-carrying capacity tests - Test 5a:
Temperature rise
IEC 60512-6–3 - Connectors for electronic equipment - EN 60512-6–3 -
Tests and measurements - Part 6–3:
Dynamic stress tests - Test 6c: Shock
IEC 60512-6–4 - Connectors for electronic equipment - EN 60512-6–4 -
Tests and measurements - Part 6–4:
Dynamic stress tests - Test 6d: Vibration
(sinusoidal)
3

---------------------- Page: 5 ----------------------
SIST EN IEC 61076-2-010:2021
EN IEC 61076-2-010:2021 (E)
IEC 60512-9–1 - Connectors for electronic equipment - EN 60512-9–1 -
Tests and measurements - Part 9–1:
Endurance tests - Test 9a: Mechanical
operation
IEC 60512-13–1 - Connectors for electronic equipment - EN 60512-13–1 -
Tests and measurements - Part 13–1:
Mechanical operation tests - Test 13a:
Engaging and separating forces
IEC 60512-13–2 - Connectors for electronic equipment - EN 60512-13–2 -
Tests and measurements - Part 13–2:
Mechanical operation tests - Test 13b:
Insertion and withdrawal forces
IEC 60512-13–5 - Connectors for electronic equipment - EN 60512-13–5 -
Tests and measurements - Part 13–5:
Mechanical operation tests - Test 13e:
Polarizing and keying method
IEC 60512-15–6 - Connectors for electronic equipment - EN 60512-15–6 -
Tests and measurements - Part 15–6:
Connector tests (mechanical) - Test 15f:
Effectiveness of connector coupling
devices
IEC 60529 1989 Degrees of protection provided by EN 60529 1991
enclosures (IP Code)
- -  + corrigendum May 1993
+ A1 1999  + A1 2000
+ A2 2013  + A2 2013
IEC 60664-1 - Insulation coordination for equipment EN IEC 60664-1 -
within low-voltage supply systems - Part 1:
Principles, requirements and tests
IEC 60998-2–1 2002 Connecting devices for low-voltage circuits EN 60998-2–1 2004
(mod) for household and similar purposes - Part
2–1: Particular requirements for connecting
devices as separate entities with screw-
type clamping units
IEC 61076-1 2006 Connectors for electronic equipment - EN 61076-1 2006
Product requirements - Part 1: Generic
specification
+ A1 2019 + A1 2019
IEC 61076-2–012 - Connectors for electrical and electronic EN IEC 61076-2– -
equipment - Product Requirements - Part012
2–012: Circular connectors - Detail
specification for connectors with inner
push-pull locking based on M12 connector
interfaces according to IEC 61076-2–101,
IEC 61076-2–109, IEC 61076-2–111 and
IEC 61076-2–113
IEC 61076-2–101 2012 Connectors for electronic equipment - EN 61076-2–101 2012
Product requirements - Part 2–101:
Circular connectors - Detail specification
for M12 connectors with screw-locking
4

---------------------- Page: 6 ----------------------
SIST EN IEC 61076-2-010:2021
EN IEC 61076-2-010:2021 (E)
IEC 61076-2–109 2014 Connectors for electronic equipment - EN 61076-2–109 2014
Product requirements - Part 2–109:
Circular connectors - Detail specification
for connectors with M 12 × 1 screw-
locking, for data transmission frequencies
up to 500 MHz
IEC 61076-2–111 2017 Connectors for electrical and electronic EN IEC 61076-2– 2018
equipment - Product requirements - Part111
2–111: Circular connectors - Detail
specification for power connectors with
M12 screw-locking
IEC 61076-2–113 2017 Connectors for electronic equipment - EN 61076-2–113 2017
Product requirements - Part 2–113:
Circular connectors - Detail specification
for connectors with M12 screw locking with
power and signal contacts for data
transmission with frequency up to 100 MHz
IEC 61984 - Connectors - Safety requirements and EN 61984 -
tests

5

---------------------- Page: 7 ----------------------
SIST EN IEC 61076-2-010:2021

---------------------- Page: 8 ----------------------
SIST EN IEC 61076-2-010:2021



IEC 61076-2-010

®


Edition 1.0 2021-05




INTERNATIONAL



STANDARD




NORME


INTERNATIONALE











Connectors for electrical and electronic equipment – Product requirements –

Part 2-010: Circular connectors – Detail specification for connectors with outer

or inner push-pull locking mechanism, based on mating interfaces according to

IEC 61076‑2‑101, IEC 61076‑2‑109, IEC 61076‑2‑111 and IEC 61076‑2‑113



Connecteurs pour équipements électriques et électroniques – Exigences de


produit –

Partie 2-010: Connecteurs circulaires – Spécification particulière relative aux

connecteurs avec mécanisme de verrouillage de type pousser-tirer externe ou


interne, basés sur des interfaces d’accouplement conformes à

l’IEC 61076‑2‑101, l’IEC 61076‑2‑109, l’IEC 61076‑2‑111 et l’IEC 61076‑2‑113








INTERNATIONAL

ELECTROTECHNICAL

COMMISSION


COMMISSION

ELECTROTECHNIQUE


INTERNATIONALE




ICS 31.220.10 ISBN 978-2-8322-9812-1




Warning! Make sure that you obtained this publication from an authorized distributor.

Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé.

® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale

---------------------- Page: 9 ----------------------
SIST EN IEC 61076-2-010:2021
– 2 – IEC 61076-2-010:2021 © IEC 2021
CONTENTS
FOREWORD . 6
INTRODUCTION . 8
1 Scope . 10
2 Normative references . 11
3 Terms and definitions . 12
4 Technical information . 13
4.1 System of levels. 13
4.1.1 Performance levels . 13
4.1.2 Compatibility levels, according to IEC 61076-1 . 13
4.2 Classification into climatic categories . 13
4.3 Contact terminations . 13
4.4 Available connector codings . 13
4.5 Ratings . 15
4.6 Marking . 15
4.7 Safety aspects . 15
5 Dimensional information . 15
5.1 General . 15
5.2 Survey of styles and variants . 15
5.2.1 General . 15
5.2.2 Fixed connectors . 15
5.2.3 Free connectors . 22
5.3 Interface dimension . 31
5.3.1 General . 31
5.3.2 Outer push-pull locking: male fixed connector side view . 32
5.3.3 Outer push-pull locking: female fixed connector side view with details
and engage-plane definition for male free cable connectors type 1 and 2 . 33
5.3.4 Inner push-pull locking: female fixed connector side view and male free
connector side view with details for both . 36
5.4 Gauges – Sizing gauges and retention force gauges . 39
6 Characteristics . 39
6.1 Classification into climatic category . 39
6.2 Electrical characteristics . 39
6.2.1 Voltage proof . 39
6.2.2 Rated voltage – Rated impulse voltage – Pollution degree . 39
6.2.3 Current-carrying capacity . 40
6.2.4 Contact resistance . 40
6.2.5 Insulation resistance. 40
6.2.6 Transmission performance . 40
6.3 Mechanical characteristics . 40
6.3.1 Mating interface . 40
6.3.2 Push-pull locking mechanism . 41
6.4 Other characteristics . 42
6.4.1 Vibration (sinusoidal) . 42
6.4.2 Shock . 42
6.4.3 Degree of protection provided by enclosures (IP code) . 42
7 Test schedule . 42
7.1 General . 42

---------------------- Page: 10 ----------------------
SIST EN IEC 61076-2-010:2021
IEC 61076-2-010:2021 © IEC 2021 – 3 –
7.2 Test schedule . 43
7.2.1 Test group P – Preliminary . 43
7.2.2 Test group AP – Dynamic/climatic . 43
7.2.3 Test group BP – Mechanical endurance . 43
7.2.4 Test group CP – Electrical load . 44
7.2.5 Test group DP – Chemical resistivity . 44
7.2.6 Test group EP – Connection method tests . 44
7.2.7 Test group FP – Electrical transmission requirements . 44
Annex A (informative) Diameter and position of the female connector body . 45
A.1 Diameter of the female connector body . 45
A.2 Position of female connector body for connectors with outer push-pull
locking . 45
A.3 Position of female connector body for connectors with inner push-pull
locking . 46
Annex B (informative) Example for L-coded connector and comparison between

screw- and inner push-pull-locking . 48
Annex C (informative) Styles of female free connectors to extend free male cable
connectors . 50

Figure 1 – Tube insert, male contacts, thread for M12 screw locking on tube . 17
Figure 2 – Fixed connector, male contacts, with M12 screw locking and outer push-pull

locking, square flange front mounting. 17
Figure 3 – Fixed connector, male contacts, with M12 screw locking and outer push-pull
locking, with wire ends, single hole front mounting thread M16 × 1,5 . 18
Figure 4 – Fixed connector, male contacts, with M12 screw locking and outer push-pull
locking, with wire ends, single hole front mounting thread M20 × 1,5 . 18
Figure 5 – Fixed connector, female contacts, with M12 screw locking and outer push-

pull locking, with wire ends, single hole front mounting thread M16 × 1,5 . 19
Figure 6 – Fixed connector, female contacts, with M12 screw locking and outer push-
pull locking, with wire ends, single hole front mounting thread M20 × 1,5 . 19
Figure 7 – Fixed connector, female contacts, with M12 screw locking and outer push-
pull locking, with wire ends, single hole front mounting thread M16 × 1,5 and mounting
orientation . 20
Figure 8 – Fixed connector, female contacts, with M12 screw locking and outer push-
pull locking, with wire ends, single hole rear mounting thread M16 × 1,5 . 20
Figure 9 – Fixed connector, female contacts, with M12 screw locking and inner push-
pull locking, with wire ends, single hole front mounting thread M16 × 1,5 . 21
Figure 10 – Fixed connector, female contacts, with M12 screw locking and inner push-
pull locking, with wire ends, single hole front mounting thread M20 × 1,5 . 21
Figure 11 – Fixed connector, female contacts, with M12 screw locking and inner push-
pull locking, with wire ends, single hole front mounting thread M16 × 1,5 and mounting
orientation . 22
Figure 12 – Fixed connector, female contacts, with M12 screw locking and inner push-

pull locking, with wire ends, single hole rear mounting thread M16 × 1,5 . 22
Figure 13 – Rewirable connector, male contacts, straight version, with outer push-pull
locking . 23
Figure 14 – Rewirable connector, male contacts, angled version, with outer push-pull
locking . 24
Figure 15 – Non-rewirable connector, male contacts, straight version, with outer push

pull locking . 24

---------------------- Page: 11 ----------------------
SIST EN IEC 61076-2-010:2021
– 4 – IEC 61076-2-010:2021 © IEC 2021
Figure 16 – Non-rewirable connector, male contacts, angled version, with outer push-
pull locking . 25
Figure 17 – Rewirable connector, female contacts, straight version, with outer push-

pull locking . 26
Figure 18 – Rewirable connector, female contacts, angled version, with outer push-pull
locking . 27
Figure 19 – Non-rewirable connector, female contacts, straight version, with outer
push-pull locking . 28
Figure 20 – Non-rewirable connector, female contacts, angled version, with outer push-

pull locking . 28
Figure 21 – Rewirable connector, male contacts, straight version, with inner push-pull
locking . 29
Figure 22 – Rewirable connector, male contacts, angled version, with inner push-pull
locking . 30
Figure 23 – Non-rewirable connector, male contacts, straight version, with inner push-

pull locking . 30
Figure 24 – Non-rewirable connector, male contacts, angled version, with inner push-
pull locking . 31
Figure 25 – Outer push-pull locking: male fixed connector side view . 32
Figure 26 – Outer push-pull locking: female fixed connector side view with details and
engage-plane definition for male free cable connector . 34
Figure 27 – Inner push-pull-locking: female fixed connector side view and male free
connector side view with details for both . 37
Figure A.1 – Diameter of the female connector body . 45
Figure A.2 – Position of the female insulating body for connectors with outer push-pull
locking . 46
Figure A.3 – Female fixed connector side view and position of insulating body . 47
Figure B.1 – Dimensions for L-coded interface dimensions according to
IEC 61076-2-111 . 48

Table 1 – Content of document . 9
Table 2 – Available connector codings . 14
Table 3 – Styles of fixed connectors . 16
Table 4 – Styles of free connectors . 23
Table 5 – Dimensions of style JM-OP, Figure 13 . 23
Table 6 – Dimensions of style KM-OP, Figure 14 . 24
Table 7 – Dimensions of style LM-OP, Figure 15. 25
Table 8 – Dimensions of style MM-OP, Figure 16 . 25
Table 9 – Dimensions of style JF-OP, Figure 17 . 26
Table 10 – Dimensions of style KF-OP, Figure 18 . 27
Table 11 – Dimensions of style LF-OP, Figure 19 . 28
Table 12 – Dimensions of style MF-OP, Figure 20 . 29
Table 13 – Dimensions of style JM-IP, Figure 21 . 29
Table 14 – Dimensions of style KM-IP, Figure 22 . 30
Table 15 – Dimensions of style LM-IP, Figure 23 . 31
Table 16 – Dimensions of style MM-IP, Figure 24 . 31
Table 17 – Dimensions of fixed connector with push pull housing and male contacts . 33

---------------------- Page: 12 ----------------------
SIST EN IEC 61076-2-010:2021
IEC 61076-2-010:2021 © IEC 2021 – 5 –
Table 18 – Dimensions for Figure 26. 35
Table 19 – Dimensions of CA for Figure 26 . 36
Table 20 – Dimensions of CD for Figure 26 . 36
Table 21 – Dimensions of CC for Figure 26 . 36
Table 22 – Dimensions for Figure 27.
...