SIST EN 301 908-10 V4.1.1:2009
(Main)Electromagnetic compatibility and Radio spectrum Matters (ERM) - Base Stations (BS), Repeaters and User Equipment (UE) for IMT-2000 Third-Generation cellular networks - Part 10: Harmonized EN for IMT-2000, FDMA/TDMA (DECT) covering essential requirements of article 3.2 of the R&TTE Directive
Electromagnetic compatibility and Radio spectrum Matters (ERM) - Base Stations (BS), Repeaters and User Equipment (UE) for IMT-2000 Third-Generation cellular networks - Part 10: Harmonized EN for IMT-2000, FDMA/TDMA (DECT) covering essential requirements of article 3.2 of the R&TTE Directive
The present document applies to terminal equipment for IMT-FT. IMT-FT is the Digital Enhanced Cordless Telecommunications (DECT) system being a member of the ITU IMT-2000 family. DECT terminal equipment consists of the following elements:
a) Fixed Part (FP);
b) Portable Part (PP);
c) Cordless Terminal Adapter (CTA);
d) Wireless Relay Station (WRS) (FP and PP combined with repeater functionality);
e) Hybrid Part (HyP) (a PP with capability to act as a FP to provide PP to PP communication).
These radio equipment types are capable of operating in all or any part of the frequency bands given in table 1. The IMT-FT (DECT) service frequency bands for transmitting and receiving for all elements are the parts of the European UMTS spectrum applicable for TDD operation, 1 900 MHz to 1 980 MHz and 2 010 MHz to 2 025 MHz, (see ERC/DEC(99)25 [18] and ERC/DEC(00)01 [19]). NOTE 1: IMT-FT equipment may have a second mode for providing operation also in the DECT band 1 880 MHz to 1 900 MHz. Application of DECT in the band 1 880 MHz to 1 900 MHz is covered by EN 301 406 [i.7]. Details of the DECT Common Interface may be found in EN 300 175 parts 1 to 8 [5] to [12]. Further details of the DECT system may be found in the ETSI Technical Reports, TR 101 178 [i.1] and ETR 043 [i.2]. The present document is intended to cover the provisions of Directive 1999/5/EC (R&TTE Directive) [1] article 3.2, which states that "[…] radio equipment shall be so constructed that it effectively uses the spectrum allocated to terrestrial/space radio communications and orbital resources so as to avoid harmful interference". In addition to the present document, other ENs that specify technical requirements in respect of essential requirements under other parts of article 3 of the R&TTE Directive [1] will apply to equipment within the scope of the present document.
Elektromagnetna združljivost in zadeve v zvezi z radijskim spektrom (ERM) - Bazne postaje (BS), ponavljalniki (repetitorji) in uporabniška oprema (UE) za celična omrežja tretje generacije IMT-2000 - 10. del: Harmonizirani EN za IMT-2000, FDMA/TDMA (DECT), ki zajema bistvene zahteve člena 3.2 direktive R&TTE
General Information
Buy Standard
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.577(Electromagnetic compatibility and Radio spectrum Matters (ERM) - Base Stations (BS), Repeaters and User Equipment (UE) for IMT-2000 Third-Generation cellular networks - Part 10: Harmonized EN for IMT-2000, FDMA/TDMA (DECT) covering essential requirements of article 3.2 of the R&TTE Directive33.100.01Elektromagnetna združljivost na splošnoElectromagnetic compatibility in general33.060.99Druga oprema za radijske komunikacijeOther equipment for radiocommunicationsICS:Ta slovenski standard je istoveten z:EN 301 908-10 Version 4.1.1SIST EN 301 908-10 V4.1.1:2009en01-september-2009SIST EN 301 908-10 V4.1.1:2009SLOVENSKI
STANDARD
SIST EN 301 908-10 V4.1.1:2009
ETSI EN 301 908-10 V4.1.1 (2009-07)Harmonized European Standard (Telecommunications series) Electromagnetic compatibilityand Radio spectrum Matters (ERM);Base Stations (BS), Repeaters and User Equipment (UE) forIMT-2000 Third-Generation cellular networks;Part 10: Harmonized EN for IMT-2000,FDMA/TDMA (DECT)covering essential requirementsof article 3.2 of the R&TTE Directive SIST EN 301 908-10 V4.1.1:2009
ETSI ETSI EN 301 908-10 V4.1.1 (2009-07)2
Reference REN/DECT-000253 Keywords 3G, DECT, digital, generic, IMT-2000, radio, regulation, testing ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00
Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C Association à but non lucratif enregistrée à la Sous-Préfecture de Grasse (06) N° 7803/88
Important notice Individual copies of the present document can be downloaded from: http://www.etsi.org The present document may be made available in more than one electronic version or in print. In any case of existing or perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF). In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at http://portal.etsi.org/tb/status/status.asp If you find errors in the present document, please send your comment to one of the following services: http://portal.etsi.org/chaircor/ETSI_support.asp Copyright Notification No part may be reproduced except as authorized by written permission. The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2009. All rights reserved.
DECTTM, PLUGTESTSTM, UMTSTM, TIPHONTM, the TIPHON logo and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. LTE™ is a Trade Mark of ETSI currently being registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association. SIST EN 301 908-10 V4.1.1:2009
ETSI ETSI EN 301 908-10 V4.1.1 (2009-07)3 Contents Intellectual Property Rights . 10 Foreword . 10 Introduction . 11 1 Scope . 12 2 References . 13 2.1 Normative references . 13 2.2 Informative references . 14 3 Definitions, symbols and abbreviations . 15 3.1 Definitions . 15 3.2 Symbols . 17 3.3 Abbreviations . 17 4 Technical requirements specifications . 18 4.1 Environmental profile . 18 4.2 Document layout . 18 4.2.1 Test suites . 19 4.2.2 Test groups. 19 4.2.3 Test cases . 20 4.3 Applicant's declaration . 20 4.4 Applicability of essential test suites . 20 4.4.1 Introduction. 20 4.4.2 Equipment that includes only a DECT RF receiver . 21 4.4.3 Equipment that includes a radio transmitter . 21 4.4.4 CTAs . 21 4.4.5 Equipment with a synchronization port . 21 4.4.6 Equipment incorporating the IPEI (PPs only) . 21 4.4.7 All FP equipment . 21 4.4.8 Equipment with combined FT and PT functionality . 21 4.4.8.1 Introduction . 21 4.4.8.2 Wireless Relay Station . 21 4.4.8.3 Direct PP to PP communication . 22 4.4.8.4 Distributed communications . 22 4.4.9 Provision of 4 Mbit/s services
Equipment that is capable of using 4-level, 8-level, 16 level and/or 64-level modulation . 22 4.4.10 Dual mode handsets . 22 4.5 Conformance requirements . 22 4.5.1 General . 22 4.5.2 Accuracy and stability of RF carriers . 23 4.5.2.1 Definition of nominal position of RF carriers . 23 4.5.2.2 Limits . 23 4.5.2.3 Conformance . 23 4.5.3 Accuracy and stability of timing parameters . 23 4.5.3.1 Definitions . 23 4.5.3.1.1 Slot structure . 23 4.5.3.1.2 Definition of the position of p0 . 25 4.5.3.2 Limits . 25 4.5.3.2.1 Reference timer accuracy and stability . 25 4.5.3.2.2 RFP transmission jitter . 25 4.5.3.2.3 PP reference timer synchronization . 26 4.5.3.3 Conformance . 26 4.5.4 Transmission burst . 26 4.5.4.1 Definitions . 26 4.5.4.1.1 Introduction . 26 4.5.4.1.2 Physical packets. 27 SIST EN 301 908-10 V4.1.1:2009
ETSI ETSI EN 301 908-10 V4.1.1 (2009-07)4 4.5.4.1.3 Transmitted power . 27 4.5.4.1.4 Normal Transmitted Power (NTP) . 27 4.5.4.1.5 Transmitter attack time . 27 4.5.4.1.6 Transmitter release time . 27 4.5.4.1.7 Minimum power . 27 4.5.4.1.8 Maximum power . 27 4.5.4.1.9 Maintenance of transmission after packet end . 27 4.5.4.1.10 Transmitter idle power output . 27 4.5.4.2 Limits . 27 4.5.4.2.1 Transmitter attack time . 27 4.5.4.2.2 Transmitter release time . 27 4.5.4.2.3 Minimum power . 27 4.5.4.2.4 Maximum power . 28 4.5.4.2.5 Maintenance of transmission after packet end . 28 4.5.4.2.6 Transmitter idle power output . 28 4.5.4.3 Conformance . 28 4.5.5 Transmitted power . 28 4.5.5.1 Definitions . 28 4.5.5.1.1 PP and RFP with an integral antenna . 28 4.5.5.1.2 PP and RFP with external connections for all antennas . 28 4.5.5.1.3 PP and RFP with both integral and external antennas . 28 4.5.5.2 Limits . 28 4.5.5.3 Conformance . 28 4.5.6 RF carrier modulation . 29 4.5.6.1 Definition . 29 4.5.6.2 Limits . 29 4.5.6.3 Conformance . 29 4.5.7 Unwanted RF power radiation . 29 4.5.7.1 General . 29 4.5.7.2 Emissions due to modulation . 29 4.5.7.2.1 Definition. 29 4.5.7.2.2 Limits . 30 4.5.7.2.3 Conformance . 30 4.5.7.3 Emissions due to transmitter transients . 30 4.5.7.3.1 Definition. 30 4.5.7.3.2 Limits . 30 4.5.7.3.3 Conformance . 30 4.5.7.4 Emissions due to intermodulation . 31 4.5.7.4.1 Definition. 31 4.5.7.4.2 Limits . 31 4.5.7.4.3 Conformance . 31 4.5.7.5 Spurious emissions when allocated a transmit channel . 31 4.5.7.5.1 Definition. 31 4.5.7.5.2 Limits . 31 4.5.7.5.3 Conformance . 31 4.5.8 Radio receiver testing . 31 4.5.8.1 Radio receiver sensitivity . 31 4.5.8.1.1 Definition. 31 4.5.8.1.2 Limits . 32 4.5.8.1.3 Conformance . 32 4.5.8.2 Radio receiver reference BER and FER . 32 4.5.8.2.1 Definition. 32 4.5.8.2.2 Limits . 32 4.5.8.2.3 Conformance . 32 4.5.8.3 Radio receiver interference performance . 32 4.5.8.3.1 Definition. 32 4.5.8.3.2 Limits . 33 4.5.8.3.3 Conformance . 33 4.5.8.4 Radio receiver blocking case 1: owing to signals occurring at the same time but on other frequencies . 33 4.5.8.4.1 Definition. 33 4.5.8.4.2 Limits . 33 SIST EN 301 908-10 V4.1.1:2009
ETSI ETSI EN 301 908-10 V4.1.1 (2009-07)5 4.5.8.4.3 Conformance . 34 4.5.8.5 Radio receiver blocking case 2: owing to signals occurring at a different time . 34 4.5.8.5.1 Definition. 34 4.5.8.5.2 Limits . 34 4.5.8.5.3 Conformance . 34 4.5.8.6 Receiver intermodulation performance . 34 4.5.8.6.1 Definition. 34 4.5.8.6.2 Limits . 34 4.5.8.6.3 Conformance . 34 4.5.8.7 Spurious emissions when the PP has no allocated transmit channel . 34 4.5.8.7.1 Definition. 34 4.5.8.7.2 Limits . 35 4.5.8.7.3 Conformance . 35 4.5.9 Intersystem synchronization (FP only) . 35 4.5.9.1 Description . 35 4.5.9.2 Wired synchronization ports . 35 4.5.9.2.1 FP as a master . 35 4.5.9.2.2 FP as a slave . 36 4.5.9.3 GPS synchronization . 36 4.5.9.3.1 FP with integrated Global Positioning System (GPS) synchronization . 36 4.5.9.3.2 External GPS synchronization device . 37 4.5.10 Equipment identity testing . 37 4.5.10.1 PP . 37 4.5.10.2 FP . 37 4.5.11 Efficient use of the radio spectrum . 38 4.5.11.1 Channel selection . 38 4.5.11.2 Channel confirmation . 38 4.5.11.2.1 For the PT . 38 4.5.11.2.2 For the FT . 38 4.5.11.3 Channel release . 38 4.5.11.4 General . 39 4.5.12 WRS testing . 39 4.5.12.1 General requirements . 39 4.5.12.2 Testing as a PP . 39 4.5.12.3 Testing as an RFP . 39 4.5.12.4 Additional requirements . 40 4.5.12.5 Conformance . 44 4.5.13 Requirements for PPs with direct PP to PP communication mode . 44 4.5.13.1 General requirements . 44 4.5.13.2 Setting the EUT in direct communications mode . 44 4.5.13.3 When the EUT has not initiated a call . 44 4.5.13.4 When the EUT initiates a call . 44 4.5.13.5 Conformance . 45 4.5.14 Distributed communications . 45 4.5.14.1 General requirements . 45 4.5.14.2 Testing as a PP . 45 4.5.14.3 Testing as an RFP . 45 4.5.14.4 Conformance . 46 4.5.15 Higher level modulation options . 46 4.5.15.1 Requirements . 46 4.5.15.2 Conformance . 46 5 Testing for compliance with technical requirements . 47 5.1 General test requirements . 47 5.1.1 Test philosophy . 47 5.1.2 Standard position .
...
ETSI EN 301 908-10 V4.1.1 (2009-07)
Harmonized European Standard (Telecommunications series)
Electromagnetic compatibility
and Radio spectrum Matters (ERM);
Base Stations (BS), Repeaters and User Equipment (UE) for
IMT-2000 Third-Generation cellular networks;
Part 10: Harmonized EN for IMT-2000,
FDMA/TDMA (DECT)
covering essential requirements
of article 3.2 of the R&TTE Directive
---------------------- Page: 1 ----------------------
2 ETSI EN 301 908-10 V4.1.1 (2009-07)
Reference
REN/DECT-000253
Keywords
3G, DECT, digital, generic, IMT-2000, radio,
regulation, testing
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
Individual copies of the present document can be downloaded from:
http://www.etsi.org
The present document may be made available in more than one electronic version or in print. In any case of existing or
perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF).
In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive
within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
http://portal.etsi.org/chaircor/ETSI_support.asp
Copyright Notification
No part may be reproduced except as authorized by written permission.
The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2009.
All rights reserved.
TM TM TM TM
DECT , PLUGTESTS , UMTS , TIPHON , the TIPHON logo and the ETSI logo are Trade Marks of ETSI registered
for the benefit of its Members.
TM
3GPP is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners.
LTE™ is a Trade Mark of ETSI currently being registered
for the benefit of its Members and of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3 ETSI EN 301 908-10 V4.1.1 (2009-07)
Contents
Intellectual Property Rights . 10
Foreword . 10
Introduction . 11
1 Scope . 12
2 References . 13
2.1 Normative references . 13
2.2 Informative references . 14
3 Definitions, symbols and abbreviations . 15
3.1 Definitions . 15
3.2 Symbols . 17
3.3 Abbreviations . 17
4 Technical requirements specifications . 18
4.1 Environmental profile . 18
4.2 Document layout . 18
4.2.1 Test suites . 19
4.2.2 Test groups. 19
4.2.3 Test cases . 20
4.3 Applicant's declaration . 20
4.4 Applicability of essential test suites . 20
4.4.1 Introduction. 20
4.4.2 Equipment that includes only a DECT RF receiver . 21
4.4.3 Equipment that includes a radio transmitter . 21
4.4.4 CTAs . 21
4.4.5 Equipment with a synchronization port . 21
4.4.6 Equipment incorporating the IPEI (PPs only) . 21
4.4.7 All FP equipment . 21
4.4.8 Equipment with combined FT and PT functionality . 21
4.4.8.1 Introduction . 21
4.4.8.2 Wireless Relay Station . 21
4.4.8.3 Direct PP to PP communication . 22
4.4.8.4 Distributed communications . 22
4.4.9 Provision of 4 Mbit/s services Equipment that is capable of using 4-level, 8-level, 16 level and/or
64-level modulation . 22
4.4.10 Dual mode handsets . 22
4.5 Conformance requirements . 22
4.5.1 General . 22
4.5.2 Accuracy and stability of RF carriers . 23
4.5.2.1 Definition of nominal position of RF carriers . 23
4.5.2.2 Limits . 23
4.5.2.3 Conformance . 23
4.5.3 Accuracy and stability of timing parameters . 23
4.5.3.1 Definitions . 23
4.5.3.1.1 Slot structure . 23
4.5.3.1.2 Definition of the position of p0 . 25
4.5.3.2 Limits . 25
4.5.3.2.1 Reference timer accuracy and stability . 25
4.5.3.2.2 RFP transmission jitter . 25
4.5.3.2.3 PP reference timer synchronization . 26
4.5.3.3 Conformance . 26
4.5.4 Transmission burst . 26
4.5.4.1 Definitions . 26
4.5.4.1.1 Introduction . 26
4.5.4.1.2 Physical packets. 27
ETSI
---------------------- Page: 3 ----------------------
4 ETSI EN 301 908-10 V4.1.1 (2009-07)
4.5.4.1.3 Transmitted power . 27
4.5.4.1.4 Normal Transmitted Power (NTP) . 27
4.5.4.1.5 Transmitter attack time . 27
4.5.4.1.6 Transmitter release time . 27
4.5.4.1.7 Minimum power . 27
4.5.4.1.8 Maximum power . 27
4.5.4.1.9 Maintenance of transmission after packet end . 27
4.5.4.1.10 Transmitter idle power output . 27
4.5.4.2 Limits . 27
4.5.4.2.1 Transmitter attack time . 27
4.5.4.2.2 Transmitter release time . 27
4.5.4.2.3 Minimum power . 27
4.5.4.2.4 Maximum power . 28
4.5.4.2.5 Maintenance of transmission after packet end . 28
4.5.4.2.6 Transmitter idle power output . 28
4.5.4.3 Conformance . 28
4.5.5 Transmitted power . 28
4.5.5.1 Definitions . 28
4.5.5.1.1 PP and RFP with an integral antenna . 28
4.5.5.1.2 PP and RFP with external connections for all antennas . 28
4.5.5.1.3 PP and RFP with both integral and external antennas . 28
4.5.5.2 Limits . 28
4.5.5.3 Conformance . 28
4.5.6 RF carrier modulation . 29
4.5.6.1 Definition . 29
4.5.6.2 Limits . 29
4.5.6.3 Conformance . 29
4.5.7 Unwanted RF power radiation . 29
4.5.7.1 General . 29
4.5.7.2 Emissions due to modulation . 29
4.5.7.2.1 Definition. 29
4.5.7.2.2 Limits . 30
4.5.7.2.3 Conformance . 30
4.5.7.3 Emissions due to transmitter transients . 30
4.5.7.3.1 Definition. 30
4.5.7.3.2 Limits . 30
4.5.7.3.3 Conformance . 30
4.5.7.4 Emissions due to intermodulation . 31
4.5.7.4.1 Definition. 31
4.5.7.4.2 Limits . 31
4.5.7.4.3 Conformance . 31
4.5.7.5 Spurious emissions when allocated a transmit channel . 31
4.5.7.5.1 Definition. 31
4.5.7.5.2 Limits . 31
4.5.7.5.3 Conformance . 31
4.5.8 Radio receiver testing . 31
4.5.8.1 Radio receiver sensitivity . 31
4.5.8.1.1 Definition. 31
4.5.8.1.2 Limits . 32
4.5.8.1.3 Conformance . 32
4.5.8.2 Radio receiver reference BER and FER . 32
4.5.8.2.1 Definition. 32
4.5.8.2.2 Limits . 32
4.5.8.2.3 Conformance . 32
4.5.8.3 Radio receiver interference performance . 32
4.5.8.3.1 Definition. 32
4.5.8.3.2 Limits . 33
4.5.8.3.3 Conformance . 33
4.5.8.4 Radio receiver blocking case 1: owing to signals occurring at the same time but on other
frequencies . 33
4.5.8.4.1 Definition. 33
4.5.8.4.2 Limits . 33
ETSI
---------------------- Page: 4 ----------------------
5 ETSI EN 301 908-10 V4.1.1 (2009-07)
4.5.8.4.3 Conformance . 34
4.5.8.5 Radio receiver blocking case 2: owing to signals occurring at a different time . 34
4.5.8.5.1 Definition. 34
4.5.8.5.2 Limits . 34
4.5.8.5.3 Conformance . 34
4.5.8.6 Receiver intermodulation performance . 34
4.5.8.6.1 Definition. 34
4.5.8.6.2 Limits . 34
4.5.8.6.3 Conformance . 34
4.5.8.7 Spurious emissions when the PP has no allocated transmit channel . 34
4.5.8.7.1 Definition. 34
4.5.8.7.2 Limits . 35
4.5.8.7.3 Conformance . 35
4.5.9 Intersystem synchronization (FP only) . 35
4.5.9.1 Description . 35
4.5.9.2 Wired synchronization ports . 35
4.5.9.2.1 FP as a master . 35
4.5.9.2.2 FP as a slave . 36
4.5.9.3 GPS synchronization . 36
4.5.9.3.1 FP with integrated Global Positioning System (GPS) synchronization . 36
4.5.9.3.2 External GPS synchronization device . 37
4.5.10 Equipment identity testing . 37
4.5.10.1 PP . 37
4.5.10.2 FP . 37
4.5.11 Efficient use of the radio spectrum . 38
4.5.11.1 Channel selection . 38
4.5.11.2 Channel confirmation . 38
4.5.11.2.1 For the PT . 38
4.5.11.2.2 For the FT . 38
4.5.11.3 Channel release . 38
4.5.11.4 General . 39
4.5.12 WRS testing . 39
4.5.12.1 General requirements . 39
4.5.12.2 Testing as a PP . 39
4.5.12.3 Testing as an RFP . 39
4.5.12.4 Additional requirements . 40
4.5.12.5 Conformance . 44
4.5.13 Requirements for PPs with direct PP to PP communication mode . 44
4.5.13.1 General requirements . 44
4.5.13.2 Setting the EUT in direct communications mode . 44
4.5.13.3 When the EUT has not initiated a call . 44
4.5.13.4 When the EUT initiates a call . 44
4.5.13.5 Conformance . 45
4.5.14 Distributed communications . 45
4.5.14.1 General requirements . 45
4.5.14.2 Testing as a PP . 45
4.5.14.3 Testing as an RFP . 45
4.5.14.4 Conformance . 46
4.5.15 Higher level modulation options . 46
4.5.15.1 Requirements . 46
4.5.15.2 Conformance . 46
5 Testing for compliance with technical requirements . 47
5.1 General test requirements . 47
5.1.1 Test philosophy . 47
5.1.2 Standard position . 48
5.1.3 Test antenna of the LT . 48
5.1.4 Substitution antenna . 48
5.1.5 Test fixture .
...
Final draft ETSI EN 301 908-10 V4.1.0 (2009-03)
Harmonized European Standard (Telecommunications series)
Electromagnetic compatibility
and Radio spectrum Matters (ERM);
Base Stations (BS), Repeaters and User Equipment (UE) for
IMT-2000 Third-Generation cellular networks;
Part 10: Harmonized EN for IMT-2000,
FDMA/TDMA (DECT)
covering essential requirements
of article 3.2 of the R&TTE Directive
---------------------- Page: 1 ----------------------
2 Final draft ETSI EN 301 908-10 V4.1.0 (2009-03)
Reference
REN/DECT-000253
Keywords
3G, DECT, digital, generic, IMT-2000, radio,
regulation, testing
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
Individual copies of the present document can be downloaded from:
http://www.etsi.org
The present document may be made available in more than one electronic version or in print. In any case of existing or
perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF).
In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive
within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
http://portal.etsi.org/chaircor/ETSI_support.asp
Copyright Notification
No part may be reproduced except as authorized by written permission.
The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2009.
All rights reserved.
TM TM TM TM
DECT , PLUGTESTS , UMTS , TIPHON , the TIPHON logo and the ETSI logo are Trade Marks of ETSI registered
for the benefit of its Members.
TM
3GPP is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners.
LTE™ is a Trade Mark of ETSI currently being registered
for the benefit of its Members and of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3 Final draft ETSI EN 301 908-10 V4.1.0 (2009-03)
Contents
Intellectual Property Rights . 10
Foreword . 10
Introduction . 11
1 Scope . 12
2 References . 13
2.1 Normative references . 13
2.2 Informative references . 14
3 Definitions, symbols and abbreviations . 15
3.1 Definitions . 15
3.2 Symbols . 17
3.3 Abbreviations . 17
4 Technical requirements specifications . 18
4.1 Environmental profile . 18
4.2 Document layout . 18
4.2.1 Test suites . 19
4.2.2 Test groups. 19
4.2.3 Test cases . 20
4.3 Applicant's declaration . 20
4.4 Applicability of essential test suites . 20
4.4.1 Introduction. 20
4.4.2 Equipment that includes only a DECT RF receiver . 21
4.4.3 Equipment that includes a radio transmitter . 21
4.4.4 CTAs . 21
4.4.5 Equipment with a synchronization port . 21
4.4.6 Equipment incorporating the IPEI (PPs only) . 21
4.4.7 All FP equipment . 21
4.4.8 Equipment with combined FT and PT functionality . 21
4.4.8.1 Introduction . 21
4.4.8.2 Wireless Relay Station . 21
4.4.8.3 Direct PP to PP communication . 22
4.4.8.4 Distributed communications . 22
4.4.9 Provision of 4 Mbit/s services Equipment that is capable of using 4-level, 8-level, 16 level and/or
64-level modulation . 22
4.4.10 Dual mode handsets . 22
4.5 Conformance requirements . 22
4.5.1 General . 22
4.5.2 Accuracy and stability of RF carriers . 23
4.5.2.1 Definition of nominal position of RF carriers . 23
4.5.2.2 Limits . 23
4.5.2.3 Conformance . 23
4.5.3 Accuracy and stability of timing parameters . 23
4.5.3.1 Definitions . 23
4.5.3.1.1 Slot structure . 23
4.5.3.1.2 Definition of the position of p0 . 25
4.5.3.2 Limits . 25
4.5.3.2.1 Reference timer accuracy and stability . 25
4.5.3.2.2 RFP transmission jitter . 25
4.5.3.2.3 PP reference timer synchronization . 26
4.5.3.3 Conformance . 26
4.5.4 Transmission burst . 26
4.5.4.1 Definitions . 26
4.5.4.1.1 Introduction . 26
4.5.4.1.2 Physical packets. 27
ETSI
---------------------- Page: 3 ----------------------
4 Final draft ETSI EN 301 908-10 V4.1.0 (2009-03)
4.5.4.1.3 Transmitted power . 27
4.5.4.1.4 Normal Transmitted Power (NTP) . 27
4.5.4.1.5 Transmitter attack time . 27
4.5.4.1.6 Transmitter release time . 27
4.5.4.1.7 Minimum power . 27
4.5.4.1.8 Maximum power . 27
4.5.4.1.9 Maintenance of transmission after packet end . 27
4.5.4.1.10 Transmitter idle power output . 27
4.5.4.2 Limits . 27
4.5.4.2.1 Transmitter attack time . 27
4.5.4.2.2 Transmitter release time . 27
4.5.4.2.3 Minimum power . 27
4.5.4.2.4 Maximum power . 28
4.5.4.2.5 Maintenance of transmission after packet end . 28
4.5.4.2.6 Transmitter idle power output . 28
4.5.4.3 Conformance . 28
4.5.5 Transmitted power . 28
4.5.5.1 Definitions . 28
4.5.5.1.1 PP and RFP with an integral antenna . 28
4.5.5.1.2 PP and RFP with external connections for all antennas . 28
4.5.5.1.3 PP and RFP with both integral and external antennas . 28
4.5.5.2 Limits . 28
4.5.5.3 Conformance . 28
4.5.6 RF carrier modulation . 29
4.5.6.1 Definition . 29
4.5.6.2 Limits . 29
4.5.6.3 Conformance . 29
4.5.7 Unwanted RF power radiation . 29
4.5.7.1 General . 29
4.5.7.2 Emissions due to modulation . 29
4.5.7.2.1 Definition. 29
4.5.7.2.2 Limits . 30
4.5.7.2.3 Conformance . 30
4.5.7.3 Emissions due to transmitter transients . 30
4.5.7.3.1 Definition. 30
4.5.7.3.2 Limits . 30
4.5.7.3.3 Conformance . 30
4.5.7.4 Emissions due to intermodulation . 31
4.5.7.4.1 Definition. 31
4.5.7.4.2 Limits . 31
4.5.7.4.3 Conformance . 31
4.5.7.5 Spurious emissions when allocated a transmit channel . 31
4.5.7.5.1 Definition. 31
4.5.7.5.2 Limits . 31
4.5.7.5.3 Conformance . 31
4.5.8 Radio receiver testing . 31
4.5.8.1 Radio receiver sensitivity . 31
4.5.8.1.1 Definition. 31
4.5.8.1.2 Limits . 32
4.5.8.1.3 Conformance . 32
4.5.8.2 Radio receiver reference BER and FER . 32
4.5.8.2.1 Definition. 32
4.5.8.2.2 Limits . 32
4.5.8.2.3 Conformance . 32
4.5.8.3 Radio receiver interference performance . 32
4.5.8.3.1 Definition. 32
4.5.8.3.2 Limits . 33
4.5.8.3.3 Conformance . 33
4.5.8.4 Radio receiver blocking case 1: owing to signals occurring at the same time but on other
frequencies . 33
4.5.8.4.1 Definition. 33
4.5.8.4.2 Limits . 33
ETSI
---------------------- Page: 4 ----------------------
5 Final draft ETSI EN 301 908-10 V4.1.0 (2009-03)
4.5.8.4.3 Conformance . 34
4.5.8.5 Radio receiver blocking case 2: owing to signals occurring at a different time . 34
4.5.8.5.1 Definition. 34
4.5.8.5.2 Limits . 34
4.5.8.5.3 Conformance . 34
4.5.8.6 Receiver intermodulation performance . 34
4.5.8.6.1 Definition. 34
4.5.8.6.2 Limits . 34
4.5.8.6.3 Conformance . 34
4.5.8.7 Spurious emissions when the PP has no allocated transmit channel . 34
4.5.8.7.1 Definition. 34
4.5.8.7.2 Limits . 35
4.5.8.7.3 Conformance . 35
4.5.9 Intersystem synchronization (FP only) . 35
4.5.9.1 Description . 35
4.5.9.2 Wired synchronization ports . 35
4.5.9.2.1 FP as a master . 35
4.5.9.2.2 FP as a slave . 36
4.5.9.3 GPS synchronization . 36
4.5.9.3.1 FP with integrated Global Positioning System (GPS) synchronization . 36
4.5.9.3.2 External GPS synchronization device . 37
4.5.10 Equipment identity testing . 37
4.5.10.1 PP . 37
4.5.10.2 FP . 37
4.5.11 Efficient use of the radio spectrum . 38
4.5.11.1 Channel selection . 38
4.5.11.2 Channel confirmation . 38
4.5.11.2.1 For the PT . 38
4.5.11.2.2 For the FT . 38
4.5.11.3 Channel release . 38
4.5.11.4 General . 39
4.5.12 WRS testing . 39
4.5.12.1 General requirements . 39
4.5.12.2 Testing as a PP . 39
4.5.12.3 Testing as an RFP . 39
4.5.12.4 Additional requirements . 40
4.5.12.5 Conformance . 43
4.5.13 Requirements for PPs with direct PP to PP communication mode . 44
4.5.13.1 General requirements . 44
4.5.13.2 Setting the EUT in direct communications mode . 44
4.5.13.3 When the EUT has not initiated a call . 44
4.5.13.4 When the EUT initiates a call . 44
4.5.13.5 Conformance . 45
4.5.14 Distributed communications . 45
4.5.14.1 General requirements . 45
4.5.14.2 Testing as a PP . 45
4.5.14.3 Testing as an RFP . 45
4.5.14.4 Conformance . 46
4.5.15 Higher level modulation options . 46
4.5.15.1 Requirements . 46
4.5.15.2 Conformance . 46
5 Testing for compliance with technical requirements . 47
5.1 General test requirements . 47
5.1.1 Test philosophy . 47
5.1.2 Standard position . 48
5.1.3 Test antenna of the LT . 48
5.1.4 Substitution antenna . 48
5.1.5 Test fixture .
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.