SIST EN ISO 20344:2022/A1:2024
(Amendment)Personal protective equipment - Test methods for footwear - Amendment 1 (ISO 20344:2021/Amd 1:2024)
Personal protective equipment - Test methods for footwear - Amendment 1 (ISO 20344:2021/Amd 1:2024)
Persönliche Schutzausrüstung - Prüfverfahren für Schuhe - Änderung 1 (ISO 20344:2021/Amd 1:2024)
Équipement de protection individuelle - Méthodes d'essai pour les chaussures - Amendement 1 (ISO 20344:2021/Amd 1:2024)
Osebna varovalna oprema - Metode preskušanja obutve - Dopolnilo A1 (ISO 20344:2021/Amd 1:2024)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-maj-2024
Osebna varovalna oprema - Metode preskušanja obutve - Dopolnilo A1 (ISO
20344:2021/Amd 1:2024)
Personal protective equipment - Test methods for footwear - Amendment 1 (ISO
20344:2021/Amd 1:2024)
Persönliche Schutzausrüstung - Prüfverfahren für Schuhe - Änderung 1 (ISO
20344:2021/Amd 1:2024)
Équipement de protection individuelle - Méthodes d'essai pour les chaussures -
Amendement 1 (ISO 20344:2021/Amd 1:2024)
Ta slovenski standard je istoveten z: EN ISO 20344:2021/A1:2024
ICS:
13.340.50 Varovanje nog in stopal Leg and foot protection
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN ISO 20344:2021/A1
EUROPEAN STANDARD
NORME EUROPÉENNE
January 2024
EUROPÄISCHE NORM
ICS 13.340.50
English Version
Personal protective equipment - Test methods for
footwear - Amendment 1 (ISO 20344:2021/Amd 1:2024)
Équipement de protection individuelle - Méthodes Persönliche Schutzausrüstung - Prüfverfahren für
d'essai pour les chaussures - Amendement 1 (ISO Schuhe - Änderung 1 (ISO 20344:2021/Amd 1:2024)
20344:2021/Amd 1:2024)
This amendment A1 modifies the European Standard EN ISO 20344:2021; it was approved by CEN on 6 November 2023.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of
this amendment into the relevant national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This amendment exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2024 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 20344:2021/A1:2024 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
European foreword
This document (EN ISO 20344:2021/A1:2024) has been prepared by Technical Committee ISO/TC 94
"Personal safety -- Personal protective equipment" in collaboration with Technical Committee CEN/TC
161 “Foot and leg protectors” the secretariat of which is held by BSI.
This Amendment to the European Standard EN ISO 20344:2021 shall be given the status of a national
standard, either by publication of an identical text or by endorsement, at the latest by July 2024, and
conflicting national standards shall be withdrawn at the latest by July 2024.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
Any feedback and questions on this document should be directed to the users’ national standards
body/national committee. A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the
United Kingdom.
Endorsement notice
The text of ISO 20344:2021/Amd 1:2024 has been approved by CEN as EN ISO 20344:2021/A1:2024
without any modification.
International
Standard
ISO 20344
Third edition
Personal protective equipment —
2021-10
Test methods for footwear
AMENDMENT 1
AMENDMENT 1
2024-01
Équipement de protection individuelle — Méthodes d'essai pour
les chaussures
AMENDEMENT 1
Reference number
ISO 20344:2021/Amd.1:2024(en) © ISO 2024
ISO 20344:2021/Amd.1:2024(en)
© ISO 2024
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
ISO 20344:2021/Amd.1:2024(en)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out through
ISO technical committees. Each member body interested in a subject for which a technical committee
has been established has the right to be represented on that committee. International organizations,
governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely
with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described
in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the different types
of ISO document should be noted. This document was drafted in accordance with the editorial rules of the
ISO/IEC Directives, Part 2 (see www.iso.org/directives).
ISO draws attention to the possibility that the implementation of this document may involve the use of (a)
patent(s). ISO takes no position concerning the evidence, validity or applicability of any claimed patent
rights in respect thereof. As of the date of publication of this document, ISO had not received notice of (a)
patent(s) which may be required to implement this document. However, implementers are cautioned that
this may not represent the latest information, which may be obtained from the patent database available at
www.iso.org/patents. ISO shall not be held responsible for identifying any or all such patent rights.
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and expressions
related to conformity assessment, as well as information about ISO's adherence to the World Trade
Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 94, Personal Safety – Personal protective
equipment, Subcommittee SC 3, Foot protection, in collaboration with the European Committee for
Standardization (CEN) Technical Committee CEN/TC 161, Foot and leg protectors, in accordance with the
Agreement on technical cooperation between ISO and CEN (Vienna Agreement).
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.
iii
ISO 20344:2021/Amd.1:2024(en)
Personal protective equipment — Test methods for footwear
AMENDMENT 1
4.2
nd
Replace the 2 paragraph by:
"If the test requires a defined condition (temperature (23 ± 2) °C and/or (50 ± 5) % RH), it is mentioned in
the test method. Where the testing in conditioned atmosphere is not required, the maximum time which
shall elapse between removal from the conditioning atmosphere and the start of testing shall not be greater
than 10 min, unless otherwise stated in the test method."
Table 1
th
Replace the text of the 4 line by:
Toecap dimensions B No 5.3 3 pairs of footwear or toe- 1 pair of toecaps
caps in sizes S-M-L
th
Replace the text of the 23 line by:
Ankle protection A Yes 5.22 3 footwear in sizes S-M-L For each footwear
1 test piece (outer)
and 1 test piece inner
(if claimed)
st
Replace the text of the 28 line by:
Height of the upper B Yes 6.2.2 3 pairs of footwear in sizes Item of footwear
S-M-L
Area for non-water B Yes 6.2.3 1 item of footwear size M 1 test piece
vapor permeable
materials
st
Replace the text of the 31 line by:
Flexing resistance B Yes 6.5 3 items of footwear in dif- 1 test piece
ferent sizes
th
Replace the text of the 37 line by:
Abrasion resistance B No 6.12 footwear or materials 2 test piece
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.