oSIST prEN 13880-4:2022

Hot applied joint sealants - Part 4: Test method for the characterization of heat resistance - Change in penetration value

This document describes a method to characterize the resistance against elevated temperature on samples of hot applied joint sealants according to EN 14188-1 by comparing the cone penetration and resilience values before and after exposure.

Heiß verarbeitbare Fugenmassen - Teil 4: Prüfverfahren zur Bestimmung der Wärmebeständigkeit - Änderung der Konus-Penetration

Dieses Dokument beschreibt ein Verfahren zur Charakterisierung der Beständigkeit gegenüber erhöhter Temperatur an Proben von heiß verarbeitbaren Fugenmassen nach EN 14188-1 durch Vergleich der Werte von Konus-Penetration und elastischem Rückstellvermögen vor und nach der Exposition.

Produits de scellement de joints appliqués à chaud - Partie 4 : Méthode d'essai pour la détermination de la résistance à la chaleur - Variation de la pénétrabilité

Ce document décrit une méthode pour caractériser la résistance à une température élevée sur des échantillons de mastics de joints appliqués à chaud selon la norme EN 14188-1 en comparant les valeurs de pénétration du cône et de résilience avant et après exposition.

Tesnilne mase za stike, ki se vgrajujejo po vročem postopku - 4. del: Preskusna metoda za karakterizacijo odpornosti proti toploti - Sprememba penetracije

General Information

• Status: Not Published
• Public Enquiry End Date: 30-Dec-2022
• ICS: 91.100.50 - Binders. Sealing materials
• ICS: 93.080.20 - Road construction materials
• Technical Committee: CES - Roads
• Current Stage: 4020 - Public enquire (PE) (Adopted Project)
• Start Date: 03-Nov-2022
• Due Date: 23-Mar-2023
• Completion Date: 21-Dec-2022
• Directive: 305/2011 - Regulation (eu) No 305/2011 of the European Parliament and of the Council of 9 march 2011 laying down harmonised conditions for the marketing of construction products and repealing council directive 89/106/eec
• Mandate: M/124 - Mandate to CEN/CENELEC concerning the execution of standardization work for harmonized standards on road construction products
• Ref Project: prEN 13880-4 - Hot applied joint sealants - Part 4: Test method for the characterization of heat resistance - Change in penetration value

Relations

• Revised: SIST EN 13880-4:2004 - Hot applied joint sealants - Part 4: Test method for the determination of heat resistance - Change in penetration value
• Effective Date: 13-Apr-2022
• Revised: SIST EN 13880-4:2004 - Hot applied joint sealants - Part 4: Test method for the determination of heat resistance - Change in penetration value
• Effective Date: 18-Jan-2023
• Revised: SIST EN 13880-4:2004 - Hot applied joint sealants - Part 4: Test method for the determination of heat resistance - Change in penetration value
• Effective Date: 19-Jan-2023

Standards Content (Sample)

SLOVENSKI STANDARD
oSIST prEN 13880-4:2022
01-december-2022
Tesnilne mase za stike, ki se vgrajujejo po vročem postopku - 4. del: Preskusna
metoda za karakterizacijo odpornosti proti toploti - Sprememba penetracije
Hot applied joint sealants - Part 4: Test method for the characterization of heat resistance
- Change in penetration value
Heiß verarbeitbare Fugenmassen - Teil 4: Prüfverfahren zur Bestimmung der
Wärmebeständigkeit - Änderung der Konus-Penetration
Produits de scellement de joints appliqués à chaud - Partie 4 : Méthode d'essai pour la
détermination de la résistance à la chaleur - Variation de la pénétrabilité
Ta slovenski standard je istoveten z: prEN 13880-4
ICS:
91.100.50 Veziva. Tesnilni materiali Binders. Sealing materials
93.080.20 Materiali za gradnjo cest Road construction materials
oSIST prEN 13880-4:2022 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN 13880-4:2022

---------------------- Page: 2 ----------------------
oSIST prEN 13880-4:2022


DRAFT
EUROPEAN STANDARD
prEN 13880-4
NORME EUROPÉENNE

EUROPÄISCHE NORM

October 2022
ICS 93.080.20 Will supersede EN 13880-4:2003
English Version

Hot applied joint sealants - Part 4: Test method for the
characterization of heat resistance - Change in penetration
value
Produits de scellement de joints appliqués à chaud - Heiß verarbeitbare Fugenmassen - Teil 4:
Partie 4 : Méthode d'essai pour la détermination de la Prüfverfahren zur Bestimmung der
résistance à la chaleur - Variation de la pénétrabilité Wärmebeständigkeit - Änderung der Konus-
Penetration
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 227.

If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.

Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.


EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 13880-4:2022 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
oSIST prEN 13880-4:2022
prEN 13880-4:2022 (E)
Contents Page
European foreword . 3
1 Scope . 4
2 Normative references . 4
3 Terms and definitions . 4
4 Principle . 4
5 Apparatus . 5
6 Procedure. 5
6.1 General . 5
6.2 Exposure at elevated temperature . 5
6.3 Cone penetration . 5
6.4 Penetration and recovery (resilience) . 5
6.5 Test conditions for storage at elevated temperature . 5
6.6 Conditioning after storage at elevated temperature . 5
7 Expression of results . 5
8 Precision . 6
9 Test report . 6
Bibliography . 7

2

---------------------- Page: 4 ----------------------
oSIST prEN 13880-4:2022
prEN 13880-4:2022 (E)
European foreword
This document (prEN 13880-4:2022) has been prepared by Technical Committee CEN/TC 227 “Road
materials”, the secretariat of which is held by BSI.
This document is currently submitted to the CEN Enquiry.
This document will supersede EN 13880-4:2003.
This document is one part of the EN 13880 series of standards, Hot applied joint sealants, which consists
of the following parts:
— Part 1: Test method for the determination of density at 25 °C
— Part 2: Test metho
...