SIST EN ISO 9856:2017
(Main)Conveyor belts - Determination of elastic and permanent elongation and calculation of elastic modulus (ISO 9856:2016)
Conveyor belts - Determination of elastic and permanent elongation and calculation of elastic modulus (ISO 9856:2016)
This International Standard specifies a method for determining the elastic and permanent elongation
of a conveyor belt and the calculation of the elastic modulus.
It is not applicable or valid for light conveyor belts as described in ISO 21183-1.
Fördergurte - Bestimmung der elastischen und dauerhaften Dehnung und Berechnung des Elastizitätsmoduls (ISO 9856:2016)
Courroies transporteuses - Détermination de l'allongement élastique et permanent et calcul du module d'élasticité (ISO 9856:2016)
ISO 9856:2016 spécifie une méthode pour la détermination de l'allongement élastique et rémanent d'une courroie transporteuse et le calcul du module d'élasticité.
Elle n'est ni applicable ni appropriée pour les courroies transporteuses légères telles que décrites dans l'ISO 21183‑1.
Naprave za kontinuirni transport - Trakovi tračnih transporterjev - Določitev elastičnega in trajnega raztezka ter izračun modula elastičnosti (ISO 9856:2016)
Ta mednarodni standard določa metodo za določanje elastičnega in trajnega raztezka traka tračnega transporterja ter izračun modula elastičnosti.
Ne uporablja se oziroma ni veljaven za lahke trakove tračnih transporterjev, kot so opisani v standardu ISO 21183-1.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 9856:2017
01-marec-2017
1DGRPHãþD
SIST EN ISO 9856:2004
SIST EN ISO 9856:2004/A1:2012
1DSUDYH]DNRQWLQXLUQLWUDQVSRUW7UDNRYLWUDþQLKWUDQVSRUWHUMHY'RORþLWHY
HODVWLþQHJDLQWUDMQHJDUD]WH]NDWHUL]UDþXQPRGXODHODVWLþQRVWL ,62
Conveyor belts - Determination of elastic and permanent elongation and calculation of
elastic modulus (ISO 9856:2016)
Fördergurte - Bestimmung der elastischen und dauerhaften Dehnung und Berechnung
des Elastizitätsmoduls (ISO 9856:2016)
Courroies transporteuses - Détermination de l'allongement élastique et permanent et
calcul du module d'élasticité (ISO 9856:2016)
Ta slovenski standard je istoveten z: EN ISO 9856:2016
ICS:
53.040.20 Deli za transporterje Components for conveyors
SIST EN ISO 9856:2017 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 9856:2017
---------------------- Page: 2 ----------------------
SIST EN ISO 9856:2017
EN ISO 9856
EUROPEAN STANDARD
NORME EUROPÉENNE
October 2016
EUROPÄISCHE NORM
ICS 53.040.20 Supersedes EN ISO 9856:2003
English Version
Conveyor belts - Determination of elastic and permanent
elongation and calculation of elastic modulus (ISO
9856:2016)
Courroies transporteuses - Détermination de Fördergurte - Bestimmung der elastischen und
l'allongement élastique et rémanent et calcul du dauerhaften Dehnung und Berechnung des
module d'élasticité (ISO 9856:2016) Elastizitätsmoduls (ISO 9856:2016)
This European Standard was approved by CEN on 5 October 2016.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2016 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 9856:2016 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 9856:2017
EN ISO 9856:2016 (E)
Contents Page
European foreword . 3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 9856:2017
EN ISO 9856:2016 (E)
European foreword
This document (EN ISO 9856:2016) has been prepared by Technical Committee ISO/TC 41 “Pulleys and
belts (including veebelts)” in collaboration with Technical CEN/TC 188 “Conveyor belts” the secretariat
of which is held by SNV.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by April 2017, and conflicting national standards shall be
withdrawn at the latest by April 2017.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent
rights.
This document supersedes EN ISO 9856:2003.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 9856:2016 has been approved by CEN as EN ISO 9856:2016 without any modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 9856:2017
---------------------- Page: 6 ----------------------
SIST EN ISO 9856:2017
INTERNATIONAL ISO
STANDARD 9856
Third edition
2016-10-15
Conveyor belts — Determination of
elastic and permanent elongation and
calculation of elastic modulus
Courroies transporteuses — Détermination de l’allongement élastique
et rémanent et calcul du module d’élasticité
Reference number
ISO 9856:2016(E)
©
ISO 2016
---------------------- Page: 7 ----------------------
SIST EN ISO 9856:2017
ISO 9856:2016(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2016, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2016 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 9856:2017
ISO 9856:2016(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Principle . 3
5 Apparatus . 3
6 Sampling . 3
7 Test pieces . 3
8 Conditioning . 3
9 Procedure. 3
10 Calculation and expression of results . 5
11 Test report . 5
Bibliography . 6
© ISO 2016 – All rights reserved iii
---------------------- Page: 9 ----------------------
SIST EN ISO 9856:2017
ISO 9856:2016(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any paten
...
SLOVENSKI STANDARD
kSIST FprEN ISO 9856:2016
01-julij-2016
1DSUDYH]DNRQWLQXLUQLWUDQVSRUW7UDNRYLWUDþQLKWUDQVSRUWHUMHY'RORþLWHY
HODVWLþQHJDLQWUDMQHJDUD]WH]NDWHUL]UDþXQPRGXODHODVWLþQRVWL ,62)',6
Conveyor belts - Determination of elastic and permanent elongation and calculation of
elastic modulus (ISO/FDIS 9856:2016)
Fördergurte - Bestimmung der elastischen und dauerhaften Dehnung und Berechnung
des Elastizitätsmoduls (ISO/FDIS 9856:2016)
Courroies transporteuses - Détermination de l'allongement élastique et permanent et
calcul du module d'élasticité (ISO/FDIS 9856:2016)
Ta slovenski standard je istoveten z: FprEN ISO 9856
ICS:
53.040.20 Deli za transporterje Components for conveyors
kSIST FprEN ISO 9856:2016 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
kSIST FprEN ISO 9856:2016
---------------------- Page: 2 ----------------------
kSIST FprEN ISO 9856:2016
FINAL
INTERNATIONAL ISO/FDIS
DRAFT
STANDARD 9856
ISO/TC 41/SC 3
Conveyor belts — Determination of
Secretariat: JISC
elastic and permanent elongation and
Voting begins
on: 20160610 calculation of elastic modulus
Voting terminates
Courroies transporteuses — Détermination de l’allongement élastique
on: 201609-02
et permanent et calcul du module d’élasticité
Please see the administrative notes on page ii
RECIPIENTS OF THIS DRAFT ARE INVITED TO
SUBMIT, WITH THEIR COMMENTS, NOTIFICATION
OF ANY RELEVANT PATENT RIGHTS OF WHICH
THEY ARE AWARE AND TO PROVIDE SUPPOR TING
DOCUMENTATION.
IN ADDITION TO THEIR EVALUATION AS
Reference number
BEING ACCEPTABLE FOR INDUSTRIAL, TECHNO
ISO/FDIS 9856:2016(E)
LOGICAL, COMMERCIAL AND USER PURPOSES,
DRAFT INTERNATIONAL STANDARDS MAY ON
OCCASION HAVE TO BE CONSIDERED IN THE
LIGHT OF THEIR POTENTIAL TO BECOME STAN
DARDS TO WHICH REFERENCE MAY BE MADE IN
©
NATIONAL REGULATIONS. ISO 2016
---------------------- Page: 3 ----------------------
kSIST FprEN ISO 9856:2016
ISO/FDIS 9856:2016(E)
ISO/CEN PARALLEL PROCESSING
This final draft has been developed within the International Organization for Standardization (ISO), and pro
cessed under the ISO-lead mode of collaboration as defined in the Vienna Agreement. The final draft was
established on the basis of comments received during a parallel enquiry on the draft.
This final draft is hereby submitted to the ISO member bodies and to the CEN member bodies for a
parallel twelve-week approval vote in ISO and formal vote in CEN.
Positive votes shall not be accompanied by comments.
Negative votes shall be accompanied by the relevant technical reasons.
COPYRIGHT PROTECTED DOCUMENT
© ISO 2016, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2016 – All rights reserved
---------------------- Page: 4 ----------------------
kSIST FprEN ISO 9856:2016
ISO/FDIS 9856:2016(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Principle . 2
5 Apparatus . 3
6 Sampling . 3
7 Test pieces . 3
8 Conditioning . 3
9 Procedure. 3
10 Calculation and expression of results . 4
11 Test report . 5
Bibliography . 6
© ISO 2016 – All rights reserved iii
---------------------- Page: 5 ----------------------
kSIST FprEN ISO 9856:2016
ISO/FDIS 9856:2016(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment,
as well as information about ISO’s adherence to the World Trade Organization (WTO) principles in the
Technical Barriers to Trade (TBT) see the following URL: www.iso.org/iso/foreword.html.
The committee responsible for this document is ISO/TC 41 Pulleys and belts (including veebelts),
Subcommittee SC 3, Conveyor belts.
This third edition cancels and replaces the second edition (ISO 9856:2003), of which it constitutes a
minor revision. It also incorporates the Amendment ISO 9856:2003/Amd 1:2012.
The normative references have been updated.
iv © ISO 2016 – All rights reserved
---------------------- Page: 6 ----------------------
kSIST FprEN ISO 9856:2016
ISO/FDIS 9856:2016(E)
Introduction
This International Standard is used in a number of situations where the permanent elongation of the
conveyor belt after mechanical conditioning is of some practical relevance and in particular in the
implementation of ISO 3870 and the application of ISO 5293.
© ISO 2016 – All rights reserved
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.