SIST EN ISO 9856:2004
(Main)Conveyor belts - Determination of elastic and permanent elongation and calculation of elastic modulus (ISO 9856:2003)
Conveyor belts - Determination of elastic and permanent elongation and calculation of elastic modulus (ISO 9856:2003)
This International Standard specifies a method for determining the elastic and permanent elongation and the calculation of the elastic modulus of a conveyor belt. It is not applicable or valid for light conveyor belts as described in EN 873.
Fördergurte - Bestimmung der elastischen und dauerhaften Dehnung und Berechnung des Elastizitätsmoduls (ISO 9856:2003)
Courroies transporteuses - Détermination de l'allongement élastique et permanent et calcul du module d'élasticité (ISO 9856:2003)
L'ISO 9856:2003 spécifie une méthode de détermination de l'allongement élastique et permanent d'une courroie transporteuse et de calcul du module d'élasticité. Elle n'est ni applicable ni appropriée pour les courroies transporteuses légères telles que décrites dans l'EN 873.
Trakovi tračnih transporterjev – Določitev elastičnega in trajnega raztezka ter izračun modula elastičnosti (ISO 9856:2003)
Ta mednarodni standard opisuje metodo za določanje elastičnega in trajnega raztezka traka tračnega transporterja ter izračun modula elastičnosti. Standard se ne uporablja oziroma ni veljaven za lahke trakove tračnih transporterjev iz standarda EN 873.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 9856:2004
01-junij-2004
1DGRPHãþD
SIST EN ISO 9856:1997
7UDNRYLWUDþQLKWUDQVSRUWHUMHY±'RORþLWHYHODVWLþQHJDLQWUDMQHJDUD]WH]NDWHU
L]UDþXQPRGXODHODVWLþQRVWL ,62
Conveyor belts - Determination of elastic and permanent elongation and calculation of
elastic modulus (ISO 9856:2003)
Fördergurte - Bestimmung der elastischen und dauerhaften Dehnung und Berechnung
des Elastizitätsmoduls (ISO 9856:2003)
Courroies transporteuses - Détermination de l'allongement élastique et permanent et
calcul du module d'élasticité (ISO 9856:2003)
Ta slovenski standard je istoveten z: EN ISO 9856:2003
ICS:
53.040.20 Deli za transporterje Components for conveyors
SIST EN ISO 9856:2004 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 9856:2004
---------------------- Page: 2 ----------------------
SIST EN ISO 9856:2004
EUROPEAN STANDARD
EN ISO 9856
NORME EUROPÉENNE
EUROPÄISCHE NORM
December 2003
ICS 53.040.20 Supersedes EN ISO 9856:1995
English version
Conveyor belts - Determination of elastic and permanent
elongation and calculation of elastic modulus (ISO 9856:2003)
Courroies transporteuses - Détermination de l'allongement Fördergurte - Bestimmung der elastischen und dauerhaften
élastique et permanent et calcul du module d'élasticité Dehnung und Berechnung des Elastizitätsmoduls (ISO
(ISO 9856:2003) 9856:2003)
This European Standard was approved by CEN on 2 December 2003.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and United
Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2003 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 9856:2003 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 9856:2004
EN ISO 9856:2003 (E)
Foreword
This document (EN ISO 9856:2003) has been prepared by Technical Committee ISO/TC 41
"Pulleys and belts (including veebelts)" in collaboration with Technical Committee CEN/TC 188
"Conveyor belts", the secretariat of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of
an identical text or by endorsement, at the latest by June 2004, and conflicting national
standards shall be withdrawn at the latest by June 2004.
This document supersedes EN ISO 9856:1995.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of
the following countries are bound to implement this European Standard: Austria, Belgium, Czech
Republic, Denmark, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy,
Luxembourg, Malta, Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and
the United Kingdom.
NOTE FROM CMC The foreword is susceptible to be amended on reception of the German
language version. The confirmed or amended foreword, and when appropriate, the normative
annex ZA for the references to international publications with their relevant European
publications will be circulated with the German version.
Endorsement notice
The text of ISO 9856:2003 has been approved by CEN as EN ISO 9856:2003 without any
modifications.
2
---------------------- Page: 4 ----------------------
SIST EN ISO 9856:2004
INTERNATIONAL ISO
STANDARD 9856
Second edition
2003-12-15
Conveyor belts — Determination of elastic
and permanent elongation and calculation
of elastic modulus
Courroies transporteuses — Détermination de l'allongement élastique et
permanent et calcul du module d'élasticité
Reference number
ISO 9856:2003(E)
©
ISO 2003
---------------------- Page: 5 ----------------------
SIST EN ISO 9856:2004
ISO 9856:2003(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall
not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the
unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2003
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
©
ii ISO 2003 – All rights reserved
---------------------- Page: 6 ----------------------
SIST EN ISO 9856:2004
ISO 9856:2003(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International
Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO9856 was prepared by Technical Committee ISO/TC41, Pulleys and belts (including veebelts),
Subcommittee SC 3, Conveyor belts.
This second edition cancels and replaces the first edition (ISO 9856:1989), which has been technically revised.
©
ISO 2003 – All rights reserved iii
---------------------- Page: 7 ----------------------
SIST EN ISO 9856:2004
ISO 9856:2003(E)
Introduction
This International Standard is used in a number of situations where the permanent elongation of the conveyor
belt after mechanical conditioning is of some practical relevance and in particular in the implementation of
ISO 3870 and the application of ISO 5293.
The equation for the calculation of the elastic modulus in the 1989 edition contained an error and omitted to
calculate the permanent elongation of the conveyor belt. In addition the figure illustrating the hysteresis loop of
the conveyor belt during mechanical conditioning was misleading and ambiguous.
These omissions and anomalies have been corrected in the present edition.
©
iv ISO 2003 – All rights reserved
---------------------- Page: 8 ----
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.