kSIST FprEN ISO 25649-6:2024
(Main)Floating leisure articles for use on and in the water - Part 6: Additional specific safety requirements and test methods for Class D devices (ISO/FDIS 25649-6:2021)
Floating leisure articles for use on and in the water - Part 6: Additional specific safety requirements and test methods for Class D devices (ISO/FDIS 25649-6:2021)
This document specifies safety requirements and test methods related to materials, safety, performance and consumer information for classified floating leisure articles for use on and in the water according to ISO 25649-1:2024.
This document is applicable to Class D floating leisure articles for use on and in water according to ISO 25649-1:2024 regardless whether the buoyancy is achieved by inflation or inherent buoyant material.
NOTE 1 Typical products forming Class D (see Figure A.1 and Figure A.2):
— inflatable climbing structures on the water;
— bouncing platforms;
— inflatable slides;
— water trampolines;
— teeter totters;
— obstacle courses.
NOTE 2 Typical places for application:
— pools;
— lakes, ponds;
— open sea;
— sea shore (no offshore winds, no currents).
Schwimmende Freizeitartikel zum Gebrauch auf und im Wasser - Teil 6: Zusätzliche besondere sicherheitstechnische Anforderungen und Prüfverfahren für Artikel der Klasse D (ISO/FDIS 25649-6:2021)
Dieses Dokument gilt für schwimmende Freizeitartikel für den Gebrauch auf und im Wasser der Klasse D nach ISO 25649-1:20xx, unabhängig davon, ob der Auftrieb durch Aufblasen oder selbstschwimmende Materialien erzielt wird.
Dieses Dokument gilt im Zusammenhang mit ISO 25649-1:20xx und ISO 25649-2:20xx.
ANMERKUNG 1 Typische Produkte der Klasse D (siehe Anhang A):
- aufblasbare Kletterstrukturen auf dem Wasser;
- Hüpfplattformen;
- aufblasbare Rutschen;
- Wassertrampoline;
- Wasserschaukeln;
- Hindernislaufbahnen.
ANMERKUNG 2 Typische Orte der Verwendung:
- Schwimmbecken;
- Seen; Teiche;
- offenes Meer;
- Küstenstrand (kein ablandiger Wind, keine Strömung).
Die folgenden Geräte liegen außerhalb des Anwendungsbereiches dieses Dokuments:
- Geräte, deren Höhe 4,5 m übersteigt, im Hinblick auf diejenigen Risiken, die sich aus sehr großen Höhen ergeben (siehe Anhang B).
Articles des loisirs flottants à utiliser sur ou dans l'eau - Partie 6: Exigences de sécurité et méthodes d'essai complémentaires propres aux dispositifs de Classe D (ISO/FDIS 25649-6:2021)
Le présent document spécifie les exigences de sécurité et les méthodes d’essai applicables aux matériaux, à la sécurité, aux performances et aux informations aux consommateurs pour les articles de loisirs flottants à utiliser sur ou dans l’eau classés conformément à l’ISO 25649-1:2024.
Le présent document est applicable aux articles de loisirs flottants de Classe D à utiliser sur ou dans l’eau conformément à l’ISO 25649-1:2024, dont la flottabilité est assurée par gonflage ou par un matériau ayant une flottabilité propre.
NOTE 1 Produits types appartenant à la Classe D (voir la Figure A.1 et la Figure A.2):
— structures gonflables d’escalade à utiliser sur l’eau;
— plateformes à rebond;
— toboggans gonflables;
— trampolines aquatiques;
— balançoires à bascule;
— courses d’obstacles.
NOTE 2 Lieux d’utilisation types:
— piscines;
— lacs, étangs;
— pleine mer;
— bord de mer (pas de vent de terre ni de courant).
Plavajoči pripomočki za prosti čas, ki se uporabljajo na vodi in v njej - 6. del: Dodatne posebne varnostne zahteve in preskusne metode za pripomočke razreda D (ISO/FDIS 25649-6:2021)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
oSIST prEN ISO 25649-6:2021
01-december-2021
Plavajoči pripomočki za prosti čas, ki se uporabljajo na vodi in v njej - 6. del:
Dodatne posebne varnostne zahteve in preskusne metode za pripomočke razreda
D (ISO/DIS 25649-6:2021)
Floating leisure articles for use on and in the water - Part 6: Additional specific safety
requirements and test methods for Class D devices (ISO/DIS 25649-6:2021)
Schwimmende Freizeitartikel zum Gebrauch auf und im Wasser - Teil 6: Zusätzliche
besondere sicherheitstechnische Anforderungen und Prüfverfahren für Artikel der Klasse
D (ISO/DIS 25649-6:2021)
Articles des loisirs flottants à utiliser sur ou dans l'eau - Partie 6: Exigences de sécurité
et méthodes d'essai complémentaires propres aux dispositifs de Classe D (ISO/DIS
25649-6:2021)
Ta slovenski standard je istoveten z: prEN ISO 25649-6
ICS:
97.220.40 Oprema za športe na Outdoor and water sports
prostem in vodne športe equipment
oSIST prEN ISO 25649-6:2021 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
oSIST prEN ISO 25649-6:2021
oSIST prEN ISO 25649-6:2021
DRAFT INTERNATIONAL STANDARD
ISO/DIS 25649-6
ISO/TC 83 Secretariat: DIN
Voting begins on: Voting terminates on:
2021-10-01 2021-12-24
Floating leisure articles for use on and in the water —
Part 6:
Additional specific safety requirements and test methods
for Class D devices
Articles des loisirs flottants à utiliser sur ou dans l'eau —
Partie 6: Exigences de sécurité et méthodes d'essai complémentaires propres aux dispositifs de Classe D
ICS: 97.220.40
THIS DOCUMENT IS A DRAFT CIRCULATED
This document is circulated as received from the committee secretariat.
FOR COMMENT AND APPROVAL. IT IS
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
ISO/CEN PARALLEL PROCESSING
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/DIS 25649-6:2021(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
©
PROVIDE SUPPORTING DOCUMENTATION. ISO 2021
oSIST prEN ISO 25649-6:2021
ISO/DIS 25649-6:2021(E)
© ISO 2021
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2021 – All rights reserved
oSIST prEN ISO 25649-6:2021
ISO/DIS 25649-6:2021(E)
Contents Page
Foreword .iv
Introduction .vi
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
4 Safety requirements and test methods . 3
4.1 General . 3
4.2 Design of buckles and other fixings . 3
4.2.1 Requirements . 3
4.2.2 Test method . 4
4.3 Sizing and admissible number of users, maximum load capacity . 4
4.3.1 Product sizing . 4
4.3.2 User sizing . 4
4.3.3 Space per person per trampoline . 4
4.4 Components . 5
4.4.1 Valves and stoppers (special requirements for Class D) . 5
4.4.2 Test method . 5
4.5 In water performance . 5
4.5.1 Class D devices, floating stability . 5
4.5.2 Floating devices not claiming to provide floating stability . 6
4.5.3 Buoyancy and amount of residual buoyancy . 6
4.5.4 Nominative buoyancy for floating leisure articles claiming floating
stability when fully inflated . 6
4.5.5 Carrying handles and climbing facilities . 7
4.5.6 Re-embarkation from the water . 9
4.5.7 Anchorage .10
4.5.8 Water depth . .11
4.5.9 Horizontal safety distance with surrounding area .13
4.5.10 Visibility.14
4.5.11 Repair kit .15
4.5.12 Springs, protection against corrosion, durability .15
4.5.13 Safety pad for trampolines and bouncy platforms .15
4.5.14 Connection of inflatable components .16
4.5.15 Swimming in close approximation under extra-large floating leisure articles .17
4.5.16 Specific requirements for swing devices as end-module or used as stand-
alone module .18
5 Instruction manual .19
6 Exclusion .20
Annex A (informative) Examples of typical products forming Class D .21
Annex B (informative) Specific information for devices exceeding 4.5m height .23
Annex ZA (informative) Relationship between this European Standard and the safety
requirements of Directive 2001/95/EC aimed to be covered .24
Bibliography .26
oSIST prEN ISO 25649-6:2021
ISO/DIS 25649-6:2021(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www .iso .org/
iso/ foreword .html.
This document was prepared by Technical Committee TC 83, Sports and other recreational facilities and
equipment, in collaboration with the European Committee Standardization (CEN) Technical Committee
CEN/TC 136, Sports, playground and other recreational facilities and equipment, in accordance with the
agreement on technical cooperation between ISO and CEN (Vienna Agreement).
This second edition cancels and replaces the first edition (ISO 25649-6:2017), which has been
technically revised.
The main changes compared to the previous edition are as follows:
— Scope : exclusion from this document of devices exceeding 4,5 m height due to risks;
— The normative references in Clause 2 and in the entire document are updated;
— Terms and definitions Clause 3 is updated, with addition of new elements;
— Sub-clause 4.2.1, update of the requirements regarding the force to apply for the test method;
— Sub-clause 4.5.3.1, integration of new requirements regarding the residual buoyancy for structure
> 1,5 m height;
— Creation of the new sub-clause 4.5.5.6 regarding products with climbing functions;
— Creation of a new sub-clause 4.5.8.1 regarding water depth information;
— Creation of a new sub-clause 4.5.8.2 providing water depth calculation for specific products;
— New requirements in the sub-clause 4.5.11.1 regarding the repair kit;
— Modification of the Clause 5 :
— Modification of requirements regarding the provision of instruction manual in case of module/
modular arrangement (system);
iv © ISO 2021 – All rights reserved
oSIST prEN ISO 25649-6:2021
ISO/DIS 25649-6:2021(E)
— New recommendation in alinea s) for the use of buoyancy vest;
— Update of Annex A (A.1 & A.2) with Figures of new products existing on the market,
— Addition of Annex B, regarding specific information for devices exceeding 4,5 m height;
— Addition of an Informative Annex ZA regarding the correspondence between this European
Standard and Commission Decision No 2005/323/EC of 21/04/2005.
A list of all parts in the ISO 25649 series can be found on the ISO website.
Any feedback or questions on this document should be directed to the user’s nation
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.