Specification for masonry units - Part 5: Manufactured stone masonry units

Festlegungen für Mauersteine - Teil 5: Betonwerksteine

Spécifications pour éléments de maçonnerie - Partie 5 : Éléments de maçonnerie en pierre reconstituée en béton

Specifikacija za zidake – 5. del: Zidaki iz umetnega kamna

General Information

Status
Withdrawn
Publication Date
31-Mar-2005
Withdrawal Date
16-Jun-2011
Current Stage
9900 - Withdrawal (Adopted Project)
Start Date
17-Jun-2011
Due Date
10-Jul-2011
Completion Date
17-Jun-2011

Relations

Buy Standard

Amendment
EN 771-5:2004/A1:2005
English language
7 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 771-5:2004/A1:2005
01-april-2005
Specifikacija za zidake – 5. del: Zidaki iz umetnega kamna
Specification for masonry units - Part 5: Manufactured stone masonry units
Festlegungen für Mauersteine - Teil 5: Betonwerksteine
Spécifications pour éléments de maçonnerie - Partie 5 : Éléments de maçonnerie en
pierre reconstituée en béton
Ta slovenski standard je istoveten z: EN 771-5:2003/A1:2005
ICS:
91.100.15 Mineralni materiali in izdelki Mineral materials and
products
SIST EN 771-5:2004/A1:2005 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 771-5:2004/A1:2005

---------------------- Page: 2 ----------------------

SIST EN 771-5:2004/A1:2005
EUROPEAN STANDARD
EN 771-5:2003/A1
NORME EUROPÉENNE
EUROPÄISCHE NORM
February 2005
ICS 91.100.30
English version
Specification for masonry units - Part 5: Manufactured stone
masonry units
Spécifications pour éléments de maçonnerie - Partie 5 : Festlegungen für Mauersteine - Teil 5: Betonwerksteine
Éléments de maçonnerie en pierre reconstituée en béton
This amendment A1 modifies the European Standard EN 771-5:2003; it was approved by CEN on 29 December 2004.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this
amendment into the relevant national standard without any alteration. Up-to-date lists and bibliographical references concerning such
national standards may be obtained on application to the Central Secretariat or to any CEN member.
This amendment exists in three official versions (English, French, German). A version in any other language made by translation under the
responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2005 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 771-5:2003/A1:2005: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN 771-5:2004/A1:2005
EN 771-5:2003/A1:2005 (E)
Contents
Page
Foreword.3
1 Modification in Contents.4
2 Modification in Normative references .4
3 Modification in 5.2 Dimensions and tolerances .4
4 Modification in 5.2.2 Tolerances .4
5 New 5.2.2.2 Flatness of bed faces.4
6 New 5.2.2.3 Plane parallelism of bed faces.5
7 Modification in 5.3 Configuration.5
8 Modification in 5.3.1 General .5
9 New 5.3.2 Configuration.5
10 Modification in 5.3.3 Flatness of surfacess .5
11 Modification in 5.8.1 Declared value.6
12 Modification in 6.1 Description and designation.6
13 Modification in Table A.1 — Number of units required for a test .6
14 Modification in Table ZA.1 — Scope and relevant clauses .6
15 Modification in Figure ZA.1 — Examples of CE marking information.6
16 Modification in Figure ZA.2 — Examples of CE marking information.7

2

---------------------- Page: 4 ----------------------

SIST EN 771-5:2004/A1:2005
EN 771-5:2003/A1:2005 (E)
Foreword
This document (EN 771-5:2003/A1:2005) has been prepared by Technical Committee CEN/TC 125 "Masonry",
the Secretariat of which is held by BSI.
This Amendment to the European Standard EN 771-5:2003 shall be given the status of a national standard,
either by publication of an identical text or by endorsement, at the latest by August 2005, and conflicting
national standards shall be withdrawn at the latest by August 2005.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive(s).
For relationship with EU Directive(s), see modifications to informative Annex ZA, which is an integral part of
this document.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland
and United Kingdom.

3

---------------------- Page: 5 ----------------------

SIST EN 771-5:2004/A1:2005
EN 771-5:2003/A1:2005 (E)

1 Modification in Contents
Delete “5.3 Configuration” and substitute “5.3 Configuration and appearance”.
2 Modification in Normative references
Make the reference to EN 772-1 undated by deleting the date "2000" and the reference to EN 998-2 undated
by deleting the date "2003".

Amend the following refe
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.