Plastics piping systems for non-pressure underground drainage and sewerage - Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) - Part 2: Specifications for pipes and fittings with smooth internal and external surface and the system, Type A

This part of EN 13476, together with EN 13476-1, specifies the definitions and requirements for pipes, fittings and the system based on unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) structured-wall piping systems that are intended to be used for non-pressure underground drainage and sewerage systems.
This part is applicable to pipes and fittings with smooth internal and external surfaces, designated as Type A.
It specifies test methods and test parameters as well as requirements.
This part is applicable to:
a)   structured-wall pipes and fittings, which are intended to be used buried underground outside the building structure; reflected in the marking of products by “U”;
b)   structured-wall pipes and fittings, which are intended to be used buried underground both outside (application area code “U”) and within the building structure (application area code “D”); reflected in the marking of products by “UD”.
This part is applicable to structured-wall pipes and fittings with or without an integral socket with elastomeric ring seal joints as well as welded and fused joints.
This part covers a range of pipe and fitting sizes, materials, pipe constructions, stiffness classes, application classes, and tolerance classes and gives recommendations concerning colours.
NOTE   It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes.

Kunststoff-Rohrleitungssysteme für erdverlegte drucklose Abwasserkanäle und -leitungen - Rohrleitungssysteme mit profilierter Wandung aus weichmacherfreiem Polyvinylchlorid (PVC-U), Polypropylen (PP) und Polyethylen (PE) - Teil 2: Anforderungen an Rohre und Formstücke mit glatter Innen- und Außenfläche und an das Rohrleitungssystem, Typ A

Dieser Teil von prEN 13476 legt gemeinsam mit prEN 13476-1 die Definitionen und Anforderungen für Rohre, Formstücke und das Rohrleitungssystem aus weichmacherfreiem Polyvinylchlorid (PVC-U), Polypropylen (PP) und Polyethylen (PE) mit profilierter Wandung fest, die für erdverlegte, drucklos betriebene Abwasserkanäle und -leitungen verwendet werden.
Dieser Teil gilt für Rohre und Formstücke mit glatten Innen- und Außenflächen, bezeichnet als Typ A.
Es werden sowohl Prüfverfahren und Prüfparameter als auch Anforderungen festgelegt.
Dieser Teil gilt für:
a)   Rohre und Formstücke mit profilierter Wandung, die ausschließlich für erdverlegte Anwendungen außer¬halb einer Gebäudestruktur vorgesehen sind; gekennzeichnet mit Anwendungs¬kennzeichen „U“;
b)   Rohre und Formstücke mit profilierter Wandung, die sowohl für erdverlegte Anwendungen außerhalb der Gebäudestruktur (Anwendungskennzeichen „U“) als auch innerhalb einer Gebäudestruktur (Anwen¬dungs¬kennzeichen „D“) vorgesehen sind; gekennzeichnet mit Anwendungs¬kennzeichen „UD“.
Dieser Teil gilt für Rohre und Formstücke mit profilierter Wandung sowohl mit glatten Enden als auch mit geformter Muffe, die mittels elastomerer Dichtringverbindungen bzw. durch Heizelement-Stumpf-, Extrusions- oder Heizwendelschweißen miteinander verbunden sind.
Diese Norm enthält Festlegungen für Maße von Rohren und Formstücken, für Werkstoffe, Rohrkonstruktionen, für Steifigkeitsklassen, Anwendungs- und Toleranzklassen und gibt Empfehlungen für die Einfärbung.
ANMERKUNG   Der Anwender bzw. Auftraggeber ist unter Berücksichtigung der eigenen Anforderungen sowie der geltenden nationalen Festlegungen und Verlegepraktiken oder -vorschriften für die entsprechende Auswahl dieser Kriterien verantwortlich.

Systèmes de canalisations en plastique pour les branchements et les collecteurs d'assainissement sans pression enterrés - Systèmes de canalisations à parois structurées en poly(chlorure de vinyle) non plastifié (PVC-U), polypropylène (PP) et polyéthylène (PE) - Partie 2: Spécifications pour les tubes et raccords avec une surface interne et externe lisse et le système, de Type A

La présente partie de l’EN 13476, conjointement avec le prEN 13476 1, spécifie les définitions et les exigences pour les tubes, les raccords et le système de canalisations fabriqués à partir de poly(chlorure de vinyle) non plastifié (PVC U), polypropylène (PP) et polyéthylène (PE), destinés à être utilisés en tant que systèmes de canalisations à parois structurées dans le domaine des branchements et des collecteurs d'assainissement enterrés sans pression.
La présente partie s'applique aux tubes et raccords avec une surface interne et externe lisse, désignés de Type A.
Elle spécifie les méthodes d'essai et les paramètres d'essai ainsi que les exigences.
La présente partie s'applique aux :
a)   tubes et raccords à parois structurées, destinés à être utilisés enterrés à l'extérieur du bâtiment ; ce qui est reflété par le marquage des produits par « U » ;
b)   tubes et raccords à parois structurées, destinés à être utilisés enterrés, aussi bien à l'extérieur (code de la zone d’application « U ») de la structure des bâtiments, qu’à l'intérieur (code de la zone d’application « D ») ; ce qui est reflété par le marquage des produits par « UD ».
La présente partie s'applique aux tubes et raccords à parois structurées qui comprennent des assemblages à bague d'étanchéité en élastomère avec ou sans emboîture intégrée ainsi que des assemblages soudés et les assemblages obtenus par fusion.
La présente partie couvre une gamme de dimensions de tubes et de raccords, de matières, de constructions de tube, de classes de rigidité, de classes d'application et de classes de tolérance et donne des recommandations concernant les couleurs.
NOTE   Il est de la responsabilité de l'acheteur ou du prescripteur de faire les sélections appropriées à partir de ces aspects, en tenant compte des exigences particulières et des règles nationales concernées et des pratiques ou codes de pose.

Cevni sistemi iz polimernih materialov za odvodnjavanje in kanalizacijo, ki delujejo po težnostnem principu in so položeni v zemljo - Cevni sistemi s strukturirano steno iz nemehčanega polivinilklorida (PVC-U), polipropilena (PP) in polietilena (PE) - 2. del: Specifikacije za cevi in fitinge z gladko notranjo in zunanjo površino in sistem, tip A

Ta del standarda EN 13476 skupaj s standardom EN 13476-1 določa definicije in zahteve za cevi, fitinge in sistem, ki temelji na nemehčanih cevnih sistemih iz polivinilklorida (PVC-U), polipropilena (PP) ter polietilena (PE) v strukturiranih stenah, ki so namenjeni za uporabo v sistemih za odvodnjavanje in kanalizacijo ter delujejo brez tlaka.
Ta del se uporablja za cevi in fitinge z gladkimi notranjimi in zunanjimi površinami, označene kot tip A.
Določa preskusne metode in preskusne parametre ter zahteve.
Ta del se uporablja za:
a) cevi in fitinge v strukturiranih stenah, ki so namenjeni za uporabo tako, da bodo zakopani v tla zunaj zgradbe; na proizvodu je oznaka »U«;
b) cevi in fitinge v strukturiranih stenah, ki so namenjeni za uporabo tako, da bodo zakopani v tla tako zunaj (koda območja uporabe »U«) kot znotraj zgradbe (koda območja uporabe »D«); na proizvodu je oznaka »UD«.
Ta del se uporablja za cevi in fitinge v strukturiranih stenah z oglavkom ali brez njega s spoji elastomernih tesnilnih obročev ter varjenimi in fuzijskimi spoji.
Ta del zajema razpon velikosti cevi in fitingov, materiale, cevne konstrukcije, razrede togosti, načina uporabe in tolerance ter ponuja priporočila v zvezi z barvami.
OPOMBA: Za ustrezno izbiro teh vidikov je odgovoren kupec ali projektant, pri čemer mora upoštevati posebne zahteve ter vse pomembne nacionalne predpise in prakse ali kodekse vgradnje.

General Information

Status
Withdrawn
Public Enquiry End Date
29-Dec-2015
Publication Date
16-May-2018
Withdrawal Date
09-Aug-2020
Current Stage
9900 - Withdrawal (Adopted Project)
Start Date
03-Aug-2020
Due Date
26-Aug-2020
Completion Date
10-Aug-2020

Relations

Buy Standard

Standard
EN 13476-2:2018
English language
54 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Kunststoff-Rohrleitungssysteme für erdverlegte drucklose Abwasserkanäle und -leitungen - Rohrleitungssysteme mit profilierter Wandung aus weichmacherfreiem Polyvinylchlorid (PVC-U), Polypropylen (PP) und Polyethylen (PE) - Teil 2: Anforderungen an Rohre und Formstücke mit glatter Innen- und Außenfläche und an das Rohrleitungssystem, Typ APlastics piping systems for non-pressure underground drainage and sewerage - Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) - Part 2: Specifications for pipes and fittings with smooth internal and external surface and the system, Type A01-junij-2018SIST EN 13476-2:2018SLOVENSKI
STANDARDSIST EN 13476-2:20071DGRPHãþD



2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Systèmes de canalisations en plastique pour les branchements et les collecteurs d'assainissement sans pression enterrés - Systèmes de canalisations à parois structurées en poly(chlorure de vinyle) non plastifié (PVC-U), polypropylène (PP) et polyéthylène (PE) - Partie 2: Spécifications pour les tubes et raccords avec une surface interne et externe lisse et le système, de Type A93.030Zunanji sistemi za odpadno vodoExternal sewage systems23.040.05Cevovodi
za zunanje sisteme za odpadno vodo in njihovi deliPipeline and its parts for external sewage systemsICS:SIST EN 13476-2:2018en,fr,deTa slovenski standard je istoveten z:EN 13476-2:2018SIST EN 13476-2:2018



SIST EN 13476-2:2018



EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 13476-2
April
t r s z ICS
t uä r v rä r sâ
{ uä r u r Supersedes EN
s u v y xæ tã t r r yEnglish Version
Plastics piping systems for nonæpressure underground drainage and sewerage æ Structuredæwall piping systems of pipes and fittings with smooth internal and external surface and the systemá Type A Systèmes de canalisations en plastique pour les branchements et les collecteurs d 5assainissements sans pression enterrés æ Systèmes de canalisations à parois Partie
tã Spécifications pour les tubes et raccords avec une surface interne et externe lisses et le systèmeá de Type A
KunststoffæRohrleitungssysteme für erdverlegte drucklose Abwasserkanäle und æleitungen æ Rohrleitungssysteme mit profilierter Wandung aus Anforderungen an Rohre und Formstücke mit glatter Innenæ und Außenfläche und an das Rohrleitungssystemá Typ A This European Standard was approved by CEN on
z February
t r s zä
egulations which stipulate the conditions for giving this European Standard the status of a national standard without any alterationä Upætoædate lists and bibliographical references concerning such national standards may be obtained on application to the CENæCENELEC Management Centre or to any CEN memberä
translation under the responsibility of a CEN member into its own language and notified to the CENæCENELEC Management Centre has the same status as the official versionsä
CEN members are the national standards bodies of Austriaá Belgiumá Bulgariaá Croatiaá Cyprusá Czech Republicá Denmarká Estoniaá Finlandá Former Yugoslav Republic of Macedoniaá Franceá Germanyá Greeceá Hungaryá Icelandá Irelandá Italyá Latviaá Lithuaniaá Luxembourgá Maltaá Netherlandsá Norwayá Polandá Portugalá Romaniaá Serbiaá Slovakiaá Sloveniaá Spainá Swedená Switzerlandá Turkey and United Kingdomä
EUROPEAN COMMITTEE FOR STANDARDIZATION COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Rue de la Science 23,
B-1040 Brussels
9
t r s z CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Membersä Refä Noä EN
s u v y xæ tã t r s z ESIST EN 13476-2:2018



EN 13476-2:2018 (E) 2 Contents Page European foreword . 4 Introduction . 6 1 Scope . 7 2 Normative references . 7 3 Terms, definitions, symbols and abbreviations . 10 3.1 Terms and definitions . 10 3.2 Symbols . 10 3.3 Abbreviations . 10 4 Material . 11 4.1 General . 11 4.2 Unplasticized poly(vinyl chloride) (PVC-U) . 11 4.3 Polypropylene (PP) . 12 4.4 Polyethylene (PE) . 14 4.5 Sealing rings . 16 4.6 Fused or welded joints . 17 4.7 Adhesives for PVC-U . 17 5 Designation of wall constructions and examples of typical jointing methods . 17 5.1 General . 17 5.2 Wall constructions designated as Type A . 17 5.3 Designation and design of joints . 18 6 Appearance and colour . 19 7 Geometrical characteristics . 19 7.1 General . 19 7.2 Dimensions . 19 7.3 Types of fittings . 25 7.4 Design length of fittings . 25 8 Physical characteristics . 25 8.1 Unplasticized poly(vinyl chloride) (PVC-U) . 25 8.2 Polypropylene (PP) . 27 8.3 Polyethylene (PE) . 28 9 Mechanical characteristics . 29 9.1 Mechanical characteristics of pipes. 29 9.2 Mechanical characteristics of fittings . 31 10 Performance requirements . 32 11 Marking . 34 11.1 General . 34 11.2 Minimum required marking . 34 11.3 Additional marking . 36 Annex A (normative)
Compound / formulation PVC-U material . 37 Annex B (normative)
Utilization of non-virgin PVC-U material . 38 B.1 Own reprocessed and recycled material from pipes and fittings . 38 SIST EN 13476-2:2018



EN 13476-2:2018 (E) 3 B.2 External reprocessed and recycled materials with agreed specifications . 38 Annex C (normative)
Compound / formulation PP material . 40 Annex D (normative)
Utilization of non-virgin PP material . 41 D.1 Own reprocessed material from pipes and fittings . 41 D.2 External reprocessed and recycled materials with an agreed specification . 41 Annex E (normative)
Compound / formulation for PE material . 43 Annex F (normative)
Utilization of non-virgin PE material . 44 F.1 Own reprocessed material from pipes and fittings . 44 F.2 External reprocessed and recycled materials with an agreed specification . 44 F.3 External reprocessed and recycled material from PE rotational-moulded fittings and other components . 44 Annex G (normative)
Impact test at 23 °C . 46 Annex
°C . 47 Annex I (normative)
Ring flexibility test at 20 % diametric deflection . 48 Annex J (informative)
Survey of possible use of reprocessed and recycled material . 49 Annex K (normative)
Impact test for large diameter pipes with structured wall . 50 K.1 Principle . 50 K.2 Apparatus . 50 K.3 Test samples . 51 K.4 Conditioning . 51 K.5 Procedure . 51 K.6 Test result . 52 Bibliography . 53
SIST EN 13476-2:2018



EN 13476-2:2018 (E) 4 European foreword This document (EN 13476-2:2018) has been prepared by Technical Committee CEN/TC 155 “Plastics piping systems and ducting systems”, the secretariat of which is held by NEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by October 2018, and conflicting national standards shall be withdrawn at the latest by October 2018. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN not be held responsible for identifying any or all such patent rights. This document supersedes EN 13476-2:2007. The main changes with respect to the previous edition are listed below: a) updating of references in Clause 2, Tables 2, 8, 9, 10, 12, 14, 16 and 17; b) deletion of Note 2 in scope; c) changed denomination ‘material’ to ‘compound / formulation’ (entire document); d) clarification requirement ‘sealing rings’ (4.5); e) correction position e3 dimension (Figure 3); f) range nominal sizes extended (Table 5, Table 6); g) references to socket dimensions added (7.2.4); h) deletion of Table 7; i) short sockets added (7.2.4, 11.2.1, 11.2.2) j) alternative test method for DCM test added in Table 8; k) changed dem to dim (Table 14); l) changed dem min to dim max (Table G.1; Table H.1); m) impact strength at 0 °C added (Table 14, Table G.1); n) deletion of long term performance of TPE seals (Table 17); o) redrafted Annexes A and B, Table B.1, Table B.2, Annex F, Table F.1, Table F.2, Annex J; p) impact test for large diameter added (Annex K); q) deleted application of recyclate without agreed specification (Annexes B, D, E, F and J); r) updated with new CEN template (entire document). SIST EN 13476-2:2018



EN 13476-2:2018 (E) 5 This standard is a part of a System Standard for plastics piping systems of particular materials for a specified application. There are a number of such System Standards. System Standards are based on the results of the work being undertaken in ISO/TC 138 “Plastics pipes, fittings and valves for the transport of fluids”, which is a Technical Committee of the International Organization for Standardization (ISO). They are supported by separate standards on test methods to which references are made throughout the System Standard. The System Standards are consistent with general standards on functional requirements and on recommended practice for installation. EN 13476 consists of the following parts under the general title “Plastics piping systems for non-pressure underground drainage and sewerage — Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE)”: — Part 1: General requirements and performance characteristics; — Part 2: Specifications for pipes and fittings with smooth internal and external surface and the system, Type A (this standard); — Part 3: Specifications for pipes and fittings with a smooth internal surface and profiled external surface and the system, Type B; — Part 4: Assessment of conformity (CEN/TS). (CEN/TS 13476-4:2013; valid for pipes up to and incl.to DN 1200). For guidance for installation, see CEN/TR 1046. National standards specifically for pipes and fittings for the transport of surface water are not considered to be conflicting with this standard and may thus be allowed to coexist. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. SIST EN 13476-2:2018



EN 13476-2:2018 (E) 6 Introduction This standard provides optional choices for impact resistance (see Annex G, Annex H and Annex K) and ring flexibility, see Annex I. As appropriate, the individual countries may select between those options in their national forewords. SIST EN 13476-2:2018



EN 13476-2:2018 (E) 7 1 Scope This part of EN 13476, together with EN 13476-1, specifies the definitions and requirements for pipes, fittings and the system based on unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) structured-wall piping systems that are intended to be used for non-pressure underground drainage and sewerage systems. This part is applicable to pipes and fittings with smooth internal and external surfaces, designated as Type A. It specifies test methods and test parameters as well as requirements. This part is applicable to: a) structured-wall pipes and fittings, which are intended to be used buried underground outside the building structure; reflected in the marking of products by “U”; b) structured-wall pipes and fittings, which are intended to be used buried underground both outside (application area code “U”) and within the building structure (application area code “D”); reflected in the marking of products by “UD”. This part is applicable to structured-wall pipes and fittings with or without an integral socket with elastomeric ring seal joints as well as welded and fused joints. This part covers a range of pipe and fitting sizes, materials, pipe constructions, stiffness classes, application classes, and tolerance classes and gives recommendations concerning colours. NOTE It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 476, General requirements for components used in drains and sewers EN 681-1, Elastomeric seals — Materials requirements for pipe joint seals used in water and drainage applications — Part 1: Vulcanized rubber EN 681-2, Elastomeric Seals — Materials requirements for pipe joint seals used in water and drainage applications — Part 2: Thermoplastic elastomers EN 681-4, Elastomeric seals — Materials requirements for pipe joint seals used in water and drainage applications — Part 4: Cast polyurethane sealing elements EN 1401-1, Plastics piping systems for non-pressure underground drainage and sewerage — Unplasticized poly(vinyl chloride) (PVC-U) — Part 1: Specifications for pipes, fittings and the system EN 1852-1, Plastics piping systems for non-pressure underground drainage and sewerage — Polypropylene (PP) — Part 1: Specifications for pipes, fittings and the system EN 12099, Plastics piping systems — Polyethylene piping materials and components — Determination of volatile content SIST EN 13476-2:2018



EN 13476-2:2018 (E) 8 EN 12666-1, Plastics piping systems for non-pressure underground drainage and sewerage — Polyethylene (PE) — Part 1: Specifications for pipes, fittings and the system EN 13476-1:2018, Plastics piping systems for non-pressure underground drainage and sewerage — Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) — Part 1: General requirements and performance characteristics EN 13476-3, Plastics piping systems for non-pressure underground drainage and sewerage — Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) — Part 3: Specifications for pipes and fittings with smooth internal and profiled external surface and the system, Type B EN 14680, Adhesives for non-pressure thermoplastics piping systems — Specifications EN 14758-1, Plastics piping systems for non-pressure underground drainage and sewerage — Polypropylene with mineral modifiers (PP-MD) — Part 1: Specifications for pipes, fittings and the system CEN/TS 15223:2017, Plastics piping systems — Validated design parameters of buried thermoplastics piping systems EN 15346:2014, Plastics — Recycled plastics — Characterization of poly(vinyl chloride) (PVC) recyclates EN ISO 580, Plastics piping and ducting systems — Injection-moulded thermoplastics fittings — Methods for visually assessing the effects of heating (ISO 580) EN ISO 1133-1:2011, Plastics — Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics — Part 1: Standard method (ISO 1133-1:2011) EN ISO 1158, Plastics — Vinyl chloride homopolymers and copolymers — Determination of chlorine content (ISO 1158) EN ISO 1167-1, Thermoplastics pipes, fittings and assemblies for the conveyance of fluids — Determination of the resistance to internal pressure — Part 1: General method (ISO 1167-1) EN ISO 1167-2, Thermoplastics pipes, fittings and assemblies for the conveyance of fluids — Determination of the resistance to internal pressure — Part 2: Preparation of pipe test pieces (ISO 1167-2) EN ISO 1183-1, Plastics — Methods for determining the density of non-cellular plastics — Part 1: Immersion method, liquid pyknometer method and titration method (ISO 1183-1) EN ISO 2505, Thermoplastics pipes — Longitudinal reversion — Test method and parameters (ISO 2505) EN ISO 2507-1, Thermoplastics pipes and fittings — Vicat softening temperature — Part 1: General test method (ISO 2507-1) EN ISO 3126, Plastics piping systems — Plastics components — Determination of dimensions (ISO 3126) EN ISO 3127, Thermoplastics pipes — Determination of resistance to external blows — Round-the-clock method (ISO 3127) EN ISO 3451-1:2008, Plastics — Determination of ash — Part 1: General methods (ISO 3451-1:2008) EN ISO 3451-5, Plastics — Determination of ash — Part 5: Poly(vinyl chloride) (ISO 3451-5) SIST EN 13476-2:2018



EN 13476-2:2018 (E) 9 EN ISO 6259-1, Thermoplastics pipes — Determination of tensile properties — Part 1: General test method (ISO 6259-1) EN ISO 9852, Unplasticized poly(vinyl chloride) (PVC-U) pipes — Dichloromethane resistance at specified temperature (DCMT) — Test method (ISO 9852) EN ISO 9967, Thermoplastics pipes — Determination of creep ratio (ISO 9967) EN ISO 9969, Thermoplastics pipes — Determination of ring stiffness (ISO 9969) EN ISO 11173, Thermoplastics pipes — Determination of resistance to external blows — Staircase method (ISO 11173) EN ISO 11357-6, Plastics — Differential scanning calorimetry (DSC) — Part 6: Determination of oxidation induction time (isothermal OIT) and oxidation induction temperature (dynamic OIT) (ISO 11357-6) EN ISO 13229, Thermoplastics piping systems for non-pressure applications — Unplasticized poly(vinyl chloride) (PVC-U) pipes and fittings — Determination of the viscosity number and K-value (ISO 13229) EN ISO 13254, Thermoplastics piping systems for non-pressure applications — Test method for watertightness (ISO 13254) EN ISO 13257:2017, Thermoplastics piping systems for non-pressure applications — Test method for resistance to elevated temperature cycling (ISO 13257:2010) EN ISO 13260, Thermoplastics piping systems for non-pressure underground drainage and sewerage — Test method for resistance to combined temperature cycling and external loading (ISO 13260) EN ISO 13262, Thermoplastics piping systems for non-pressure underground drainage and sewerage — Thermoplastics spirally-formed structured-wall pipes — Determination of the tensile strength of a seam (ISO 13262) EN ISO 13263, Thermoplastics piping systems for non-pressure underground drainage and sewerage — Thermoplastics fittings — Test method for impact strength (ISO 13263) EN ISO 13264, Thermoplastics piping systems for non-pressure underground drainage and sewerage — Thermoplastics fittings — Test method for mechanical strength or flexibility of fabricated fittings (ISO 13264) EN ISO 13967, Thermoplastics fittings — Determination of ring stiffness (ISO 13967) EN ISO 13968, Plastics piping and ducting systems — Thermoplastics pipes — Determination of ring flexibility (ISO 13968) ISO 6259-2, Thermoplastics pipes — Determination of tensile properties — Part 2: Pipes made of unplasticized poly(vinyl chloride) (PVC-U), chlorinated poly (vinyl chloride) (PVC-C) and high-impact poly (vinyl chloride) (PVC-HI) ISO 13259, Thermoplastics piping systems for underground non-pressure applications — Test method for leaktightness of elastomeric sealing ring type joints ISO 18373-1, Rigid PVC pipes — Differential scanning calorimetry (DSC) method — Part 1: Measurement of the processing temperature SIST EN 13476-2:2018



EN 13476-2:2018 (E) 10 3 Terms, definitions, symbols and abbreviations 3.1 Terms and definitions For the purposes of this document, the terms and definitions given in EN 13476-1:2018 apply. ISO and IEC maintain terminological databases for use in standardization at the following addresses: http://www.electropedia.org/ http://www.iso.org/obp 3.2 Symbols A length of engagement, or maximum pull-out whilst maintaining tightness C length of the sealing zone de outside diameter dem mean outside diameter dim mean inside diameter dn nominal diameter dsm,min minimum mean inside diameter of socket e wall thickness (at any point) ec construction height emin minimum wall thickness of pipe or spigot e2 wall thickness at any point of the cylindrical part of a socket e3 wall thickness at any point of a sealing ring groove of a socket e4 wall thickness of the inside layer (waterway wall thickness) e5 wall thickness of the inside layer under a hollow section l effective length of a pipe L1,min minimum length of a spigot IMP 23C impact resistance determined at +23 °C f impact resistance determined at
« s r °C 3.3 Abbreviations CaCO3 calcium carbonate CT close tolerance DN nominal size DN/ID nominal size related to inside diameter DN/OD nominal size related to outside diameter H50 value for impact resistance of a pipe MgCO3 magnesium carbonate Mg3Si4O10(OH)2 magnesium silicate, talcum SIST EN 13476-2:2018



EN 13476-2:2018 (E) 11 MFR melt mass-flow rate OIT oxidation induction time PE polyethylene PP polypropylene PP-MD mineral modified PP PVC-U unplasticized poly(vinyl chloride) RF ring flexibility performance S pipe series S SDR standard dimension ratio SN ring stiffness class TIR true impact rate TPE thermo plastic elastomer VST vicat softening temperature 4 Material 4.1 General The material shall be one of the following: unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) or polyethylene (PE), to which are added additives needed to facilitate the manufacture of components conforming to this document, including the relevant annexes. 4.2 Unplasticized poly(vinyl chloride) (PVC-U) 4.2.1 General The compound / formulation shall be PVC-U to which are added additives needed to facilitate the manufacture of components conforming to the requirements of this document (see also Annex A). NOTE Additional information on the characteristics of PVC-U compound and components is given in EN 13476-1:2018, Annex A. 4.2.2 Pipe and fitting compound / formulation characteristics When tested in accordance with the test method as specified in Table 1 using the indicated parameters, the compound / formulation shall have characteristics conforming to the requirements given in Table 1. SIST EN 13476-2:2018



EN 13476-2:2018 (E) 12 Table 1 — Compound / formulation of PVC-U pipes and injection-moulded fittings Characteristic Requirements Test parameters Test method Resistance to internal pressure a b c No failure during the test period End caps Type A or Type B EN ISO 1167-1 and EN ISO 1167-2 Orientation Free Number of test pieces 3 Test temperature 60 °C Circumferential stress for pipe compound / formulation 10 MPa Circumferential stress
for fitting compound / formulation 6,3 MPa Conditioning period Shall conform to
EN ISO 1167-1 Type of test Water-in-water Test period 1 000 h a This requirement does not apply to the specified intermediate layer of a Type A1 pipe. b For the extrusion compounds for the internal and external layers of a multilayer pipe, this test shall be carried out in the form of a solid wall pipe made from the relevant compound / formulation. c For injection-moulding compounds, this test shall be carried out i
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.