SIST EN 4180:2004
(Main)Aerospace series - Circular tubes, for fluids in titanium and titanium alloys - Wide tolerances - Diameter 4 mm < D < 40 mm - Dimensions
Aerospace series - Circular tubes, for fluids in titanium and titanium alloys - Wide tolerances - Diameter 4 mm < D < 40 mm - Dimensions
This standard specifies the dimensions and tolerances of:
Circular tubes, for fluids
in titanium and titanium alloys
Wide tolerances
Diameter 4 mm * D * 40 mm
for aerospace applications.
Luft- und Raumfahrt - Runde Leitungsrohre aus Titan und Titanlegierungen - Weite Toleranzen - Durchmesser 4 mm L D L 40 mm - Maße
Diese Norm legt die Maße und Toleranzen von
runden Leitungsrohren
aus Titan und Titanlegierungen
Weite Toleranzen
Durchmesser 4 mm * D * 40 mm
für die Luft- und Raumfahrt fest.
Série aérospatiale - Tubes circulaires, pour canalisations en titane et alliages de titane - Tolérances larges - Diametres 4 mm < D < 40 mm - Dimensions
La présente norme spécifie les dimensions et les tolérances des :
Tubes circulaires, pour canalisations
en titane et alliages de titane
Tolérances larges
Diametres 4 mm L D L 40 mm
pour applications aérospatiales.
Aerospace series - Circular tubes, for fluids in titanium and titanium alloys - Wide tolerances - Diameter 4 mm < D < 40 mm - Dimensions
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 4180:2004
01-maj-2004
Aerospace series - Circular tubes, for fluids in titanium and titanium alloys - Wide
tolerances - Diameter 4 mm < D < 40 mm - Dimensions
Aerospace series - Circular tubes, for fluids in titanium and titanium alloys - Wide
tolerances - Diameter 4 mm < D < 40 mm - Dimensions
Luft- und Raumfahrt - Runde Leitungsrohre aus Titan und Titanlegierungen - Weite
Toleranzen - Durchmesser 4 mm L D L 40 mm - Maße
Série aérospatiale - Tubes circulaires, pour canalisations en titane et alliages de titane -
Tolérances larges - Diametres 4 mm < D < 40 mm - Dimensions
Ta slovenski standard je istoveten z: EN 4180:2001
ICS:
49.080 /HWDOVNLLQYHVROMVNL Aerospace fluid systems and
KLGUDYOLþQLVLVWHPLLQGHOL components
SIST EN 4180:2004 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 4180:2004
---------------------- Page: 2 ----------------------
SIST EN 4180:2004
EUROPEAN STANDARD
EN 4180
NORME EUROPÉENNE
EUROPÄISCHE NORM
December 2001
ICS 49.080
English version
Aerospace series - Circular tubes, for fluids in titanium and
titanium alloys - Wide tolerances - Diameter 4 mm D 40 mm
- Dimensions
Série aérospatiale - Tubes circulaires, pour canalisations Luft- und Raumfahrt - Runde Leitungsrohre aus Titan und
en titane et alliages de titane - Tolérances larges - Titanlegierungen - Weite Toleranzen - Durchmesser 4 mm
Diamètres 4 mm D 40 mm - Dimensions D 40 mm - Maße
This European Standard was approved by CEN on 2 May 2001.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,
Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2001 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 4180:2001 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 4180:2004
EN 4180:2001 (E)
Foreword
This European Standard has been prepared by the European Association of Aerospace Manufacturers
(AECMA).
After inquiries and votes carried out in accordance with the rules of this Association, this Standard has
received the approval of the National Associations and the Official Services of the member countries of
AECMA, prior to its presentation to CEN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by June 2002, and conflicting national standards shall be withdrawn at
the latest by June 2002.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark,
Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal,
Spain, Sweden, Switzerland and the United Kingdom.
2
---------------------- Page: 4 ----------------------
SIST EN 4180:2004
EN 4180:2001 (E)
0 Introduction
This standard is part of the series of EN metallic material standards for aerospace applications. The general
organization o
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.