SIST EN ISO 5182:2011
(Main)Resistance welding - Materials for electrodes and ancillary equipment (ISO 5182:2008)
Resistance welding - Materials for electrodes and ancillary equipment (ISO 5182:2008)
ISO 5182:2008 specifies the characteristics of materials for resistance welding electrodes and ancillary equipment which are used for carrying current and transmitting force to the work.
Widerstandsschweißen - Werkstoffe für Elektroden und Hilfseinrichtungen (ISO 5182:2008)
Diese Internationale Norm legt die Eigenschaften von Werkstoffen für Widerstands-Schweißelektroden und Hilfseinrichtungen, die zur Strom- und Kraftzuführung für den Betrieb verwendet werden, fest.
Soudage par résistance - Matériaux pour électrodes et équipements annexes (ISO 5182:2008)
L'ISO 5182:2008 spécifie les caractéristiques des matériaux pour électrodes de soudage par résistance et équipements annexes utilisés pour le transport du courant et la transmission de l'effort de soudage.
Uporovno varjenje - Materiali za elektrode in pomožno opremo (ISO 5182:2008)
Ta mednarodni standard določa karakteristike materialov za elektrode za uporovno varjenje in pomožno opremo, ki se uporabljajo za prevajanje toka in prenos sile na proizvod.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 5182:2011
01-december-2011
Uporovno varjenje - Materiali za elektrode in pomožno opremo (ISO 5182:2008)
Resistance welding - Materials for electrodes and ancillary equipment (ISO 5182:2008)
Widerstandsschweißen - Werkstoffe für Elektroden und Hilfseinrichtungen (ISO
5182:2008)
Soudage par résistance - Matériaux pour électrodes et équipements annexes (ISO
5182:2008)
Ta slovenski standard je istoveten z: EN ISO 5182:2009
ICS:
25.160.20 Potrošni material pri varjenju Welding consumables
SIST EN ISO 5182:2011 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 5182:2011
---------------------- Page: 2 ----------------------
SIST EN ISO 5182:2011
EUROPEAN STANDARD
EN ISO 5182
NORME EUROPÉENNE
EUROPÄISCHE NORM
April 2009
ICS 25.160.20
English Version
Resistance welding - Materials for electrodes and ancillary
equipment (ISO 5182:2008)
Soudage par résistance - Matériaux pour électrodes et Widerstandsschweißen - Werkstoffe für Elektroden und
équipements annexes (ISO 5182:2008) Hilfseinrichtungen (ISO 5182:2008)
This European Standard was approved by CEN on 10 April 2009.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2009 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 5182:2009: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 5182:2011
EN ISO 5182:2009 (E)
Contents Page
Foreword .3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 5182:2011
EN ISO 5182:2009 (E)
Foreword
The text of ISO 5182:2008 has been prepared by Technical Committee ISO/TC 44 “Welding and allied
processes” of the International Organization for Standardization (ISO) and has been taken over as EN ISO
5182:2009 by Technical Committee CEN/TC 121 “Welding” the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by October 2009, and conflicting national standards shall be withdrawn at
the latest by October 2009.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 5182:2008 has been approved by CEN as a EN ISO 5182:2009 without any modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 5182:2011
---------------------- Page: 6 ----------------------
SIST EN ISO 5182:2011
INTERNATIONAL ISO
STANDARD 5182
Third edition
2008-01-15
Resistance welding — Materials for
electrodes and ancillary equipment
Soudage par résistance — Matériaux pour électrodes et équipements
annexes
Reference number
ISO 5182:2008(E)
©
ISO 2008
---------------------- Page: 7 ----------------------
SIST EN ISO 5182:2011
ISO 5182:2008(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
COPYRIGHT PROTECTED DOCUMENT
© ISO 2008
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2008 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 5182:2011
ISO 5182:2008(E)
Contents Page
Foreword. iv
1 Scope. 1
2 Normative references. 1
3 Terms and definitions. 1
4 Classification. 1
4.1 Group A — Copper and copper alloys. 1
4.2 Group B — Sintered materials. 2
4.3 Group C — Dispersion-strengthened copper (DSC) alloys. 2
5 Specifications. 2
5.1 Requirements. 2
5.2 Chemical composition. 2
5.3 Mechanical properties. 2
5.4 Electrical properties. 2
6 Methods of test . 2
6.1 Vickers hardness test. 2
6.2 Electrical properties. 2
6.3 Softening temperature test . 3
7 Designation. 3
8 Application. 3
9 Hardness conversions . 3
Annex A (informative) Typical applications. 6
Annex B (informative) Hardness conversion. 8
Annex C (informative) Different alloy designations. 9
Bibliography . 10
© ISO 2008 – All rights reserved iii
---------------------- Page: 9 ----------------------
SIST EN ISO 5182:2011
ISO 5182:2008(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 5182 was prepared by Technical Committee ISO/TC 44, Welding and allied processes, Subcommittee
SC 6, Resistance welding.
This third edition cancels and replaces the second edition (ISO 5182:1991), which has been technically
revised.
Requests for official interpretations of any aspect of this International Standard should be directed to the
Secretariat of ISO/TC 44/SC 6 via your national standards body, a complete listing of which can be found at
www.iso.org.
iv © ISO 2008 – All rights reserved
---------------------- Page: 10 ----------------------
SIST EN ISO 5182:2011
INTERNATIONAL STANDARD ISO 5182:2008(E)
Resistance welding — Materials for electrodes and ancillary
equipment
1 Scope
This International Standard specifies the characteristics of materials for resistance welding electrodes and
ancillary equipment which are used for carrying current and transmitting force to the work.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 6507-1, Metallic materials — Vickers hardness test — Part 1: Test method
ASTM E1004, Standard practice for determining electrical conductivity using the electromagnetic (eddy-
current) method
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
3.1
softening temperature
maximum temperature that, if maintained for 2 h, will result in a reduction in ambient temperature hardness of
a maximum of 15 % of the “as received” value
4 Classification
4.1 Group A — Copper and copper alloys
This group defines four types of material:
Type 1: Non-heat-treatable alloys of high conductivity and medium hardness, the wrought forms of which are
given their strengths by cold working during manufacture.
Type 2: Alloys which are harder than type 1 and in which the mechanical properties have been developed by
heat treatment during manufacture or by a combination of heat treatment and cold working.
Type 3: Heat-treated alloys which have superior mechanical properties to type 2 but a lower electrical
conductivity than either type 1 or type 2.
Type 4: Alloys having certain specialised properties which may, in some cases, be obtained either by cold
working or by heat treatment. Alloys of this type are not necessarily interchangeable with each other.
© ISO 2008 – All r
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.